Gebruiksaanwijzing /service van het product 9 van de fabrikant Ford
Ga naar pagina of 29
9 FORD.
CONTENTS APPLICA TIONS 9 FORD MANUAL GENERAL OPERA TION SPECIAL FUNCTIONS TIPS & HINTS REMOTE CONTROL PROGRAMMING CODED ACCESS SYSTEMS.
9 APPLICA TIONS VEHICLE TYPE KEYS YEAR SYSTEM CABLE KA PETROL 3 KEYS & 2 KEYS 96/97 97/98 99> 2002 > PATS 2 ISO PATS 3 ISO PATS 3 SCP PATS 3 CAN ADC110-B ADC110-B ADC110-B ADC110-B FIESTA/ C.
APPLICA TIONS VEHICLE TYPE KEYS YEAR SYSTEM GALAXY PETROL V6 TYPE 1 TYPE 2 3 KEYS 2 KEYS 2 KEYS > 97 97 > 00 00 > PATS 2 PATS 3 GALAXY DIESEL 2 KEYS 2 KEYS 2 KEYS > 97 97 > 00 00 > P.
GENERAL OPERA TION INTRODUCTION The FORD PATS systems were introd uced on Ford vehicles on 94.5 M.Y. vehicles , and was available from March 1994. There have been many variations on the original system fitted. This system has a separate PATS Amp lifier, however on subsequent systems the PATS module was incorp orated into the Engine Management ECU.
GENERAL OPERA TION KEY OPERATION - 98¼ MY ONWARDS The newer systems are only supplie d with 2 keys. Both keys are required to program furt her slave keys. Up to a maximum of 8 keys can be programmed to this PAT S system. KEY PROGRAMMING - UP TO 98 ¼ MY NOTE : Clear ALL Fault codes before prog ramming.
GENERAL OPERA TION KEY PROGRAMMING - 98¼ MY ONWARDS NOTE : Clear ALL Fault codes before prog ramming. Master keys can only be prog ramm ed using the 2 PATS keys (A and B) the FDS2000 or the AD PROGRAMMING SYST EM system. NOTE : In some cases the vehi cle doors must be closed to perform the re-programming seque nce.
GENERAL OPERA TION PATS SYSTEM - PROBE ONLY The PATS system fitted to the Prob e is unlike the other systems. The main difference is the system ca nnot be diagnosed with the FDS2000 or the AD PROGRAMMING SYSTEM. Addit ional keys and re- programming of new keys are perfor med in a different procedure as well.
SPECIAL FUNCTIONS CLEARING/PROGRAMMING PATS 1 & 2 SYSTEM (PETROL) ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS DIAGNOSTIC MENU PRESS ENTER KEY > CLEAR PATS 1 SYSTEM KEYS PROGRAMMED DIAGNOST.
SPECIAL FUNCTIONS CLEARING/PROGRAMMING PATS 1 & 2 SYSTEM (PETROL) PROGRAM KEYS 3 KEYS REQUIRED PRESS ENTER KEY The key in the igni tion is now pro- grammed as the master key.
SPECIAL FUNCTIONS CLEARING/PROGRAMMING PATS 1 & 2 SYSTEM (DIESEL) ECU IDENTIFICATION FAULT CODES SPECIAL FUNCTIONS DIAGNOSTIC MENU PRESS ENTER KEY > CLEAR PATS 2 SYSTEM KEYS PROGRAMMED DIAGNOST.
SPECIAL FUNCTIONS CLEARING/PROGRAMMING PATS 1 & 2 SYSTEM (DIESEL) CLEAR PATS 2 SYSTEM ALL KEYS CLEARED KEYS PROGRAMMED : 1 PRESS ENTER KEY PROGRAM KEYS 3 KEYS REQUIRED PRESS ENTER KEY NOTE : If CONDITIO NS INCORRECT is displayed th en check th e connectio n to the diesel pump, an d clean the connec- tions.
SPECIAL FUNCTIONS CLEARING PATS 3 SYSTEM (PETROL & DIESEL ENG INES) CLEAR PATS 3 KEY GAINING ACCESS TIME ELAPSED 0:50 TIME REQUIRED 10:00 ACCESS STATUS IN PROGRESS BACK TO ABORT CLEAR PATS 3 SYSTEM MIN KEYS REQUIRED : 2 TIMED ACCESS CLEAR TIME 10:00 KEYS PROGRAMMED : 2 PRESS ENTER KEY Follow the screen instructions to clear the PATS system.
SPECIAL FUNCTIONS CLEARING PATS SYSTEM (FALCON) NOTE : Minimum 2 keys required. NOTE : Ensure all ve hicle doors remain closed at all times. Connect TESTER to vehicle diagnostic connector, select Ford Falcon. Select BEM first and press ENTER . DO NOT TURN IGNITION ON when screen requests to.
SPECIAL FUNCTIONS CLEARING PATS SYSTEM (FALCON) FALCON P.C.M. PATS PRESS ENTER KEY Wait for door locks to cycle and then press ENTER key. Disconnect TESTER from vehicle. Wait 30 seconds after disconnecti ng TESTER Insert one of the keys into the ignitio n and turn IGNITION ON.
SPECIAL FUNCTIONS CHECKING KEYS PROGRAMMED PATS SYSTEM CLEARING TIMES CLEAR PATS 1 SYSTEM > KEYS PROGRAMMED DIAGNOSTIC MENU PRESS ENTER KEY KEYS PROGRAMMED 3 PRESS ENTER KEY Using the UP and DOWN keys select the KEYS PROGRAMMED. The number of keys stored in the Immobiliser ECU will be displayed.
SPECIAL FUNCTIONS ADD KEY FUNCTION CLEAR PATS 1 SYSTEM KEYS PROGRAMMED > ADD KEY DIAGNOSTIC MENU PRESS ENTER KEY CLEAR PATS 3 KEY GAINING ACCESS TIME ELAPSED 0:50 TIME REQUIRED 10:00 ACCESS STATUS IN PROGRESS BACK TO ABORT NOTE : On some vehi cles a function is available to add a key without deleting the old keys.
TIPS & HINTS SYSTEM TYPES 3 KEY SYSTEM—RED CHIP MASTER KEY SYSTEM (4 C GLAS S TRANSPONDERS) For this system, con nect TESTER be fore switching ignition ON.
TIPS & HINTS GENERAL If communication is made with the ve hicle, and then no communication is experienced later or the communication is random, check battery voltage and ensure it is at least 12.2 volts. This is particularly important on the SCP vehicles, and all Transit models.
TIPS & HINTS Example Code : 31 The PATS system has it’s own self di agnosis test proced ure which flashes codes. The PATS LED will flash quickl y for 1 minute, and then start flash- ing the faul.
REMOTE CONTROL PROGRAMMING Fiesta 96> & Escort 98> (Radio 3 Button) Procedure 1. Insert Key and turn to II, then Turn Key from II to I and back to II four times within 3 sec- onds 2. The PATS LED should light. Turn Key to Position 0. 3. Press the Unlock button and keep it pre ssed until the PATS LED flashes 4 times.
REMOTE CONTROL PROGRAMMING Fiesta 96, Puma (Infrared 2 Button) Procedure 1. Turn Ignition switch to Position I and back to 0 as soon as the PATS LED in the clock lights (The system is now ready for programming, to a maximum time limit of 30 seconds) 2.
REMOTE CONTROL PROGRAMMING Scorpio 95> (Radio 3 Button) 1. Turn Ignition 4 times from 0 to I, e nding at position I. An audible tone should be heard 2. Press the Remote Unlock button – there should be another audible tone 3. If more than one Remote then Step 2 should be repeated for each remote in turn, within ten seconds of each other.
REMOTE CONTROL PROGRAMMING Focus Built from 12.2000 Onwards Note:The ignition must be turned off befor e attempting to reprogram the key fob. 11. The unlocking mode can be changed by pre ssing the locking and unlocking buttons on the remote transmitter simultaneously for a minimum of four seconds.
FORD CODED ACCESS INTRODUCTION The Ford coded access system was introduced in the year 2002, and the first vehicle that had this system was the FORD KA.
FORD CODED ACCESS 9 PLEASE FOLLO W THESE INSTRU CTIONS CAREFU LLY .... 1. PLEASE FIRST ENSURE YOU HAVE YOUR FORUM USERNAME AND PA SSWORD BEFORE YOU START. 2. PLEASE ENSURE YOU HAVE FORD/MAZDA CODED SOFTWARE ENABLED AND LOADED ON YOUR TESTER. 3. PLEASE SELECT ‘FOR D CODED’ FROM THE MAIN MENU 4.
FORD CODED ACCESS 9 5. INSERT FORUM USER NAME 6. INSERT FORUM PASSWORD 7. INSERT TESTER SERIAL NUMBER 8. INSERT TESTER PASSCODE 9. INSERT VEHICLE VIN NUMBER 10. SELECT VEHICLE MODEL 11. USING THE AD100, MVP, TCODE, DM100 OR CODESEEKER CONN ECT TO THE VEHICLE AS DESCRIBED IN THE MANUAL.
FORD CODED ACCESS 9 15. INSERT THE DETAILS FROM THE TEST ER INT O THE WEB PAGE AS FOLLO WS ... 16. ONCE ALL DETAILS HAVE BEEN ENTERE D CORR ECTLY PRESS THE SUBMIT BUTTO N. 17. THE SYSTEM WILL TH EN TR Y AND CALCULATE THE I NCODE. NOTE : THIS WILL TAKE 5 MINUTES TO CALCU LATE.
FORD CODED ACCESS 9 19. AFTER 5 MINUTES THE FOLLOWING SCREEN WILL BE DISPLAYED ... 20. INSERT THE CODE FROM OPTION 1 INTO TH E TESTER. 21. THE TESTER SHOULD EITHER ACCEPT THE CODE AND SAY ‘ACCESS GRANTED’ OR ‘INCORRECT INVALID’ 22. IF THE CODE FAIL’S, DISCONNECT THE TESTER.
Een belangrijk punt na aankoop van elk apparaat Ford 9 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Ford 9 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Ford 9 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Ford 9 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Ford 9 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Ford 9 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Ford 9 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Ford 9 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.