Gebruiksaanwijzing /service van het product Speaker van de fabrikant Fresco
Ga naar pagina of 20
F RESCO ™ i user ’s manual M A RTIN L OGA N the loudspeaker technology company ®.
2 Contents & Introduction C ONTENTS AND I NTRODUCTION Contents and Introduction . . . . . . . . . . . . . . . . . . . 2 Contents Introduction Installation in Brief . . . . . . . . . . . . . . . . . . . . . . . . 3 Operation . . . . . . . . . . . .
Installation in Brief 3 I NST ALLA TION IN B RIEF W e know you are eager to hear your new F resco i loudspeaker , so this section is provided to allow fast and easy set up. Once you have it operational, please take the time to read, in depth, the rest of the information in this manual.
Use the best speaker cables you can. The length and type of speaker cable used in your system will have an audible effect. Under no circumstance should a wire of gauge higher (thinner) than #16 be used. In general, the longer the length used, the greater the necessity of a lower gauge, and the lower the gauge, the better the sound.
NOTE: MartinLogan recommends using 5 wall anchors to secure each F resco i to a wall. During the installation, if any of the screw/wall anchor positions are over a stud, it is recommended to screw directly into the stud. NOTE: T o assure that your F resco i is safely wall mounted, these instructions must be carefully followed.
6 Mounting the Fresco i On A Wall or Ceiling NOTE: F resco i’s bracket assembly consists of two main parts: the wall bracket (attaches to the wall) and the cabinet bracket (attaches to the F resco i).
Mounting the Fresco i On A Wall or Ceiling 7 Changing the Direction of R otation Figure 7. Remove the 2 cap nuts and washers from the hinges. Figure 8. Remove the wall bracket from the cabinet bracket. Figure 9. Remove the 2 set screws. Figure 10. Change hinge pin locations.
8 Mounting the Fresco i On A Wall or Ceiling Required hardware (included): (6) M4 screws Required tools (included): 2.5mm Allen tool 1 P repare a flat surface with padding and sheets to protect the speaker as you work on it. R emove the F resco i's grill cloth and carefully place the F resco i face down on the work surface.
Required hardware (included): (5) wall anchors (5) 1" Phillips head wood screws Required tools (included): 6mm Allen tool Required tools (not included): Lev el Electric drill and 1 / 4 " and 1 / 8 " drill bits Phillips screwdriver 1 Hold the F resco i at the mounting location.
10 Mounting the Fresco i On A Wall or Ceiling NOTE: F igures 19–24 illustrate the F resco i mounted in 4 different configurations. 3 Mark your wall with the center point for the wall bracket (see figure 19).
Mounting the Fresco i On A Wall or Ceiling 11 5 Set the wall bracket aside. Using a 1 / 8 " bit, drill a pilot hole at all five points marked in the previous steps. If a pilot hole hits a stud during this step, DO NO T WIDEN that pilot hole or install a wall anchor at that location.
9 Place the F resco i onto the wall bracket and carefully slide the F resco i into place (see figure 23). 10 Using a 6mm Allen tool, attach a washer and cap nut onto each pin. Do not f ully tighten the cap nuts (see figure 23). 11 Make the signal connections from the amplifier (see ‘ Operation ’, pages 4).
H OME T HEA TER Home Theater 13 Figure 26. F resco i loudspeakers as front, center and surround (effects) channels. Abyss subwoofers as 0.1 (effects) channel. It had long been the practice of stereo buffs to connect their television to a stereo system.
14 ATF (Advanced Thin Film) AT F ( A D V ANCED T HIN F ILM ) A TF Operation The MartinLogan A TF transducer (based on RADIA planar technology) consists of a micro-thin, low -mass Kaladex diaphragm with an ultra-light, etched conductive aluminum surface suspended between two high f ield strength neodymium super magnet arrays (see figure 27).
ATF (Advanced Thin Film) 15 How do I clean my speakers? Just use a dust free cloth or a soft brush to remove the dust from your speakers. W e recommend a specialty cloth (available at the Xtat ic shop at www .martinlogan. com) that cleans your speakers better than anything else we have tried.
16 Dimensional Drawings D IMENSIONAL D RA WINGS.
System Frequency R esponse 75–20,000 Hz ± 3 dB Sensitivity 90 dB/2.83 volts/meter Impedance 5 ohms Crossover Frequency 500, 3200 Hz Components Air core coils, metal film and low dissipation electrolytic capacitors W oofer T ype T wo 4” (10.
18 Glossary of Audio Terms G LOSSARY OF A UDIO T ERMS AC. Abbreviation for alternating current. Active crossover . Uses active devices (transistors, ICs, tubes) and some form of power supply to operate. Amplitude. The extreme range of a signal. Usually measured from the average to the extreme.
Glossary of Audio Terms 19 Inductance. The property of an electrical circuit by which a varying current in it produces a varying magnetic field that introduces voltages in the same circuit or in a nearby circuit. It is measured in henrys. Inductor . A device designed primarily to introduce inductance into an electrical circuit.
Lawrence, K ansas, USA tel 785.749.0133 fax 785.749.5320 www .martinlogan.com M A RTIN L OGA N the loudspeaker technology company ©2006 MartinLogan. All rights reserved.
Een belangrijk punt na aankoop van elk apparaat Fresco Speaker (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Fresco Speaker heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Fresco Speaker vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Fresco Speaker leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Fresco Speaker krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Fresco Speaker bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Fresco Speaker kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Fresco Speaker . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
