Gebruiksaanwijzing /service van het product SPX-F17M van de fabrikant Alpine
Ga naar pagina of 20
SPX- F17M Component 2-way Single Channel Speaker System/ Paire de haut-parleurs à canal unique OWNER’S MANUAL Please read before using this equipment MANUEL DE L'UTILISA TEUR V euillez lire le présent manuel avant la mise en service du matériel ALPINE ELECTRONICS, INC.
2 Attention UTILISER LES ACCESSOIRES SPECIFIES ET LES INS T ALLER CORRECTEMENT . L ’utilisation d’autres pièces non désignées risque de provoquer des dommages à l’intérieur de l’appareil ou son installa- tion risque de ne pas être faite correctement, et les pièces desserrées peuvent provoquer des dangers.
3 19. Screw st4.2x9.5mm / Vis st4.2x9.5 mm …………….......………. x1 20. Screw st4.2x19mm / V is st4.2x19 mm ...………………...……… x2 21. Screw st4.2x19mm / V is st4.2x19 mm .........……………………… x1 22. Wing nut M4 / Écrou à oreilles M4 .
4 T abel of Contents Installation W oofer .......................................................................................... 5 T weeter ........................................................................................ 7 Crossover Network.
5 Installation W oofer: Surface mount Notes: l Attach gasket tape as shown, then lock speaker into grille ring. l If spacer ring is used with grille, snap-fit tabs on spacer ring must be removed for proper fit. st4.2x25mm W oofer: Flush mount Notes: l Attach gasket tape as shown.
6 Installation W oofer: Factory/OEM custom fit Notes: l Attach gasket tape as shown. l Use appropriate adapter pattern for OEM fit, then break away any unused tabs. st4.2x25mm W oofer: Factory/stealth Notes: l Attach gasket tape as shown. st4.2x25mm Hardware: l Use st4.
7 Installation W oofer: Factory/Size-down Notes: l Attach gasket tape as shown. l Use appropriate adapter pattern for OEM fit, then break away any unused tabs.
8 T weeter: Flush mount Notes: l Pass wires through terminal cover and connect to terminals. l Press terminal cover snuggly over tweeter housing, making sure connections are not exposed. l Attach mounting spring, adjusting screw depth and spring tension as needed.
9 Notes: l Remove network cover , and secure base as shown. l Connect wires to terminal blocks accordingly . (see System Connection Diagrams section) l Make appropriate jumper settings using jumper puller tool. (see Crossover Network Settings section) l Re-secure network cover .
10 Crossover Network Settings Introduction Configuration du filtre de voies Introduction Phase relationships are critical to driver interaction and the perception of realism. Crossovers must be designed around actual speaker placement to avoid cancellation and response aberrations.
11 Crossover Network Settings Configuration du filtre de voies Jumper Group Function Please read the following pages carefully to determine which network configuration is most appropriate for your particular installation.
12 Crossover Network Settings System T ype 1 Speaker Placement Description: In this system type, woofer and tweeter are mounted close together at an equal distance from the listener . Configuration A is the default setting of the network, but assumes essentially on axis positioning.
13 Crossover Network Settings System T ype 1 Filter Description: In this system type, both woofer and tweeter are equidistant from the listening position and mounted close together . While the kick-panel is one of the more common locations to achieve this, it is certainly not the only one.
14 Crossover Network Settings System T ype 2 Speaker Placement Description: In this system type , w oofer and tweeter are mounted at diff erent locations and at diff erent distances from the listener .
15 Crossover Network Settings System T ype 2 Filter Description: In this system type, both woofer and tweeter are mounted apart at dif ferent distances and angles relative to the listening position, with the tweeter as the closest driver .
16 Crossover Network Settings System T ype 3 Speaker Placement Description: In this system type, woofer and tweeter are mounted close together on the dashboard, rear deck, or other surface that presents an oblique angle to the listener .
17 Crossover Network Settings System T ype 3 Filter Description: Despite the fact that both drivers are mounted in the same plane and in close proximity in this system type, their orientation results in the acoustic center of the tweeter being farther away .
18 Crossover Network Settings System T ype 4 (Fully/Partially Active) Speaker Placement Description: In this system type , some le vel of e xter nal signal processing is a vailable , allo wing use of the network in a par tially or ev en fully active mode.
19 Crossover Network Settings System T ype 4 Filter Description: Fully active systems have often been considered to be the most flexible, but they are certainly not the most effective in all cases.
System T ype Component 2-wa y speaker P ower Handling (peak/RMS) 300/75W Impedance 4 W F requency Response 30-35 kHz Net W eight 2.5 kg Drivers General Speaker siz e 6,5” 28 mm Speaker T ype Woofer/Midrange T w eeter P ower Handling (RMS) 75 W 150 W V oice Coil Impedance (nom) 4 W 4 W F requency Response (-10dB) 10 kHz >40 kHz Sensitivity (@2.
Een belangrijk punt na aankoop van elk apparaat Alpine SPX-F17M (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Alpine SPX-F17M heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Alpine SPX-F17M vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Alpine SPX-F17M leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Alpine SPX-F17M krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Alpine SPX-F17M bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Alpine SPX-F17M kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Alpine SPX-F17M . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
