Gebruiksaanwijzing /service van het product B17-3 van de fabrikant Fujitsu
Ga naar pagina of 37
Monitor Operating Manual English SCENICVIEW B17-3/B19-3/P19-3.
Are there… ... any technical problems or other questions which y ou would like to be clarified? Please contact our help desk (see Warranty Booklet). The latest information on our products, tips, updates, etc., can be found on the internet under: http://www.
.
This manual was produced by Xerox Global Serv ices Published by Fujitsu Siemens Computers GmbH Order No.: A 26361-K1143-Z120-1-7619 Edition 3 AG 08/07.
SCENICVIEW B17-3/B19-3/P19-3 LCD monitor Operating Manual august 2007 edition.
VESA, DDC and DPMS are registered tradem arks of Video Electronics Standards Association. Copyright © Fujitsu Siemens Computers GmbH 2007 All rights, including rights of translation, reproduc tion by printing, copying or similar methods, in part or in whole, are reserved.
Contents Introduction ........................................................................................................................................... 1 Notational conventions ................................................................
Contents A26361-K1143-Z120-1-7619, edition 3.
Introduction Your new LCD (Liquid Cry stal Display) monitor SCENICVIEW B17-3/B19-3/P19-3 offers numerous features and functions, for example: ● TFT display (Thin Film Transistor; ac tive matrix) ●.
SCENICVIEW B17-3/B19-3/P19-3 Notational conventions The meanings of the symbols and fonts used in this manual are as follows: Pay particular attention to text marked with th is symbol. Failure to observe this w arning endangers your life, destroys the device, or may lead to loss of data.
SCENICVIEW B17-3/B19-3/P19-3 ● To ensure sufficient ventilation, the intake and exhaust air openings of the monitor must never be blocked. ● The monitor automatically sets itself to a mains voltage in the range of 100 V to 240 V. Ensure that the local mains voltage lies within these limits.
SCENICVIEW B17-3/B19-3/P19-3 Power cable To guarantee safe operation, use the cable supplied. Us e the following guidelines if it is necessary to replace the original cable set. ● The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements.
SCENICVIEW B17-3/B19-3/P19-3 FCC Class B Compliance Statement The following statement applies to the products covered in this manual, unless otherwise specified herein.
SCENICVIEW B17-3/B19-3/P19-3 Energy Star Guidelines The Fujitsu Siemens LCD monitor SC ENICVIEW B17-3/B19-3/P19-3 is designed to conserve electricity by dropping to less than 1 W when it goes into standby, suspend and OFF mode. With this new power management the LCD monitor SCENICVIEW B17-3/B19-3/P19-3 qualifies for the U.
SCENICVIEW B17-3/B19-3/P19-3 Checking the contents of the consignment The display surface of the LCD monitor is sensitive to pressure and scratches. Always hold the device by the casing! ! ► Unpack all the individual parts. ► Check the delivery for damage incurred during transportation.
SCENICVIEW B17-3/B19-3/P19-3 Installing an ergonomic video workstation 1 1 2 1 = Windows Avoid direct and re flected glare. Avoid glare from electric lighting. 1 = Edge of desk 2 = Permissible reaching sector Position the keyboard where it is easiest to reach.
SCENICVIEW B17-3/B19-3/P19-3 Mounting and removing the monitor base The display surface is susceptible to scrat ching! Therefore, lay the monitor on a soft surface when mounting or re moving the monitor base. ! Folding out monitor base When delivered the lower part of the monitor base is folded up and secured to the monitor by a collar.
SCENICVIEW B17-3/B19-3/P19-3 ► Proceed according to the four steps in the illustrations to fold out the monitor base. 10 A26361-K1143-Z120-1-7619, edition 3.
SCENICVIEW B17-3/B19-3/P19-3 Removing monitor base Before you can use a swivel arm or a w all bracket, you must remove the monitor base: ! The display surface is susceptible to scratching! ► Switch off the monitor and pull the power plug out of the pow er socket.
SCENICVIEW B17-3/B19-3/P19-3 Connecting the monitor ! Please take note of the safety information in the " Important notes " chapter. CE conformance and optimum picture qualit y are guaranteed only if y ou use the data cables supplied. Do not cover the ventilati on openings of the monitor.
SCENICVIEW B17-3/B19-3/P19-3 Connecting cables to the monitor The monitor ports are protected by a cover. ► Remove the cover. 1 5 3 2 4 6 7 7 1 = Power connector 2 = DVI-D connection socket (DIGITAL.
SCENICVIEW B17-3/B19-3/P19-3 Connecting cables to the computer Information on the computer connec tions and interfaces is contained in the operating manual for your computer. If your computer has two monitor por ts ("onboard" screen controller and separate graphics card), the monitor port for the s eparate graphics card is usually active.
SCENICVIEW B17-3/B19-3/P19-3 Adjusting portrait format The monitor can be turned from the "wide format" (landscape mode) into the "high format" position (portrait mode).
SCENICVIEW B17-3/B19-3/P19-3 Switching the monitor on and off (P19-3) The main switch on the underside and the On/Off swit ch on the front of the monitor are used to switch it on and off. ► Switch on the monitor via the main switch (4) on the underside.
SCENICVIEW B17-3/B19-3/P19-3 Notes on power management If your computer is equipped with power managemen t, the monitor can support this function fully .
SCENICVIEW B17-3/B19-3/P19-3 Changing the monitor settings When putting the monitor into operation for the fi rst time, the screen display should be optimally adapted to the screen controller used and adjus ted in accordance with your needs.
SCENICVIEW B17-3/B19-3/P19-3 Locking the OSD menu The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings. ► Press and hold the SELECT/MENU button for a few seconds while y ou switch on the monitor with the ON/OFF switch.
SCENICVIEW B17-3/B19-3/P19-3 The corresponding setting window (here: Image Adjust ) is display ed (on the right-hand side). The first function ( H-Position ) is highlighted. ► If necessary, press the 6 or 5 button to mark another function. ► Press the SELECT/MENU button to select the highlighted function.
SCENICVIEW B17-3/B19-3/P19-3 Adjusting size and position Calling the Image adjust setting window H-Position Adjusting the horizontal position With this function you move the pi cture to the left or to the right. V-Position Adjusting the vertical position With this function you move the picture up or down.
SCENICVIEW B17-3/B19-3/P19-3 Setting display of the OSD menu Calling the OSD Setup setting window Language Setting language for the OSD menu With this function you choose between E nglish (default setting), French, German, Italian and Spanish as the language for the OSD menu.
SCENICVIEW B17-3/B19-3/P19-3 Displaying information Calling the Information setting window With this function the model designation, serial number , resolution, H/V frequency, input signal and polarity of the sync hronisation signal are display ed.
SCENICVIEW B17-3/B19-3/P19-3 Troubleshooting Should an error occur, first check the following point s. If the distortion is still not eliminated, the monitor should, if possible, be checked on another computer. If you are unable to solve the probl em, please inform our help desk.
SCENICVIEW B17-3/B19-3/P19-3 Having this problem? Check the following points: Picture is wrongly adjusted ► Press the SELECT/MENU button to activate the function Factory Recall . The Auto Processing message is displayed. Picture disturbances (vertical lines) ► Press the EXIT/AUTO button to perform the auto- adjustment of the screen.
SCENICVIEW B17-3/B19-3/P19-3 Notes regarding the DIN EN ISO 13406-2 standard Permanently unlit or lit pixels The standard of production tec hniques today cannot guarantee an absolutely fault-free screen display. A few isolated constant lit or unlit pixe ls (picture elements) may be present.
SCENICVIEW B17-3/B19-3/P19-3 Technical data B17-3 B19-3 / P19-3 Dimensions and weight Visible diagonals: 43 cm 48 cm Dot pitch: 0.264 mm 0.294 mm Screen size: Width: Height: 337.9 mm 270.3 mm 376.3 mm 301 mm Maximal resolution: 1280 x 1024 1280 x 1024 Dimensions incl.
SCENICVIEW B17-3/B19-3/P19-3 Environmental conditions Environment class 3K2, IEC 721 Rated range of operation: Humidity: 15 °C .... 35 °C 20 % .... 85 % Limit range of operation: Humidity: 5 °C .... 35 °C 20 % .... 85 % Condensation must be avoided.
SCENICVIEW B17-3/B19-3/P19-3 Pin assignment D-SUB 1 5 6 10 11 15 Pin Meaning Pin Meaning 1 Video input red 9 +5 V (DDC) 2 Video input green 10 Sync. earth 3 Video input blue 11 Earth 4 Earth 12 DDC-Data 5 Earth 13 H.
Een belangrijk punt na aankoop van elk apparaat Fujitsu B17-3 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Fujitsu B17-3 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Fujitsu B17-3 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Fujitsu B17-3 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Fujitsu B17-3 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Fujitsu B17-3 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Fujitsu B17-3 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Fujitsu B17-3 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
