Gebruiksaanwijzing /service van het product ESPRIMO C5730 van de fabrikant Fujitsu
Ga naar pagina of 58
ESPRIMO C Operating Manual.
Are there ... ... any technical questions or problems? Please contact: • our Hotline/Help Desk (refer to the enclosed Help Desk List or go to: " http://ts. fujitsu.c om/sup port/hel pdesk . html" ) • your sales partner • your sales of fi ce Further information can be found in the "Safety" and "Warranty" manuals.
.
Published by Fujitsu T echnology Solutions GmbH A26361-K1002-Z220-1-7619, Edition 2 2009/08 Produced by XEROX Global Services.
ESPRIMO C Y our ESPRIMO C 1 Important notes 3 Getting started 6 Operation 16 T roubleshooting and tips 22 System ex pan sions 27 T echnical data 47 Index 48 Operating Manual.
ESPRIMO is a registered trademark of Fujitsu T echnology Solutions GmbH. Windows XP , Windows V ista and Windows 7 are regist ered trademarks of Microsoft Corporation. PS/2 is a registered trademark of International Business Machines, Inc. Pentium is a registered trademark of Intel Corporation, USA.
Content s Contents Y o u r E S P R I M O C ................... ................... ............... ................. 1 Notational conven tions .... ................... .................. ............... .......... 2 I m p o r t a n t n o t e s .......
Contents I n s t a l l i n g n e w s o f t w a r e ......................... ................... ................... ... 2 6 H a r d d i s k c o n t e n t s , r e s t o r i n g ........................ .................. ................... 2 6 T i p s .
Y our ESPRIMO C Y our ESPRIMO C Overview ... is availa b le with various con fi guration levels which differ in terms o f hardw are and software. Y ou can install accessible drives (for example a DVD drive) and other modu les. This manual tells you how to start u sing you r device and how to operate it in daily use.
Yo u r E S P R I M O C Notational conventions Pay particu lar attention to text marked with this symbol. Failure to observe these warnings could pose a risk to health, damage the device or lead to loss of data. The w arra nty will be i nvalidated if the device becomes defective through failure to observe these warnings.
Important notes Important notes Impor tantnotes Notes In this chapter you will fi nd information regarding safety which it is essential to take note of when working with your device . Safety information Safetyinformation Note Pay attention to the information provided in the "Safety" manual and in the fo llowing safety note s.
Important note s Cleaning the device Device, Transpo rtatio n Retransportati on Systemunit, seeDevi ce T urn of f all power and equipment switches and remove the power plug from the mains supply . Do not clean any interior parts yourself, leave this job to a service technician.
Important notes FCC Class B Com pliance Statement The following statement applies to the products covered in this manual, unless otherwise speci fi ed herein.
Getting s tarted Getting started Gettingstarted Please observe the safet y information in the "Impo r tant notes ", Page 3 chapter. Unpacking and checking the delivery It is recommended not to throw away the original packaging material! It may be required for reshipment at some later date.
Getting started S e t t i n gu pt h ed e v i c e Workstation Ergonomic Device When installing your device, please read the recommendations and safety notes in the "Safety" manual. Only install the device in th e operating positions fo r which it is intended.
Getting s tarted V ertical operating position (optional) Proceed as follows to operate the device in the vertical operating position: Vert icalope ratingpo sition Operatingposition, vertical Rubber/plasticf eet Sidecover ► D isconnect the cables if required.
Getting started Horizontal operating posit ion w ith rubber/plastic f eet Horizontaloperatingposition Operatingposition, horizontal Rubber/plasticfeet The horizontal operating position is only p ermitted with the rubber/plastic feet (due to the heat generated on the underside).
Getting s tarted Connecting external devices Read the documen tation on the external device before connecting it. With th e exception of USB de vices, always remove all power plugs before connecting externa l devices! Do not connect or disconnect cables during a thunderstorm.
Getting started Ports on the device Ports Externa ldevices Device The ports are located on the front and back of the device. Not all ports are necessarily present on your device. The standard ports are marked with t he symbols shown below (or sim ilar).
Getting s tarted Connecting the mouse Depending on the equipment level selected, your device will be supplied with a USB mouse or a PS/2 mouse. Mouse, Connecting, Connecting a USB mouse ► C onnect the USB mouse to one of the USB ports on the device.
Getting started Device drivers Devicedrive rs Devicedrive rs, The devices connecte d to the parallel or ser ial port r equire drivers. Y our operating system already includes many drivers. If the re quired drive is missing, insta ll it. Current drivers are usually available on the Internet or will be supplied on a data carrier.
Getting s tarted Connecting the device to the mains voltage Device Connecting Devi ce ► C heck the voltage setting. 2 1 ► C onnect the power ca ble to the device. ► Plug the power plug into a properly grounded mains outlet. T h ed e v i c ei s fi tted with a wide voltage range power supply .
Getting started Switch on the monitor and the machine ► Switch on the monitor (see operating instructions for the monitor). ► Press the on/off button on the front of the machine. The o perational display will light up and the machine will start.
Operation Operation Switch the device on ► If necessary , switch the monitor on (see the operating manual for the monitor). Device Monitor ► Press the ON/OFF switch on the fron t of the device. The power-on indicator lights green and the device is started.
Operation Power indicator Powerindicator Power-onindicator Powerindicator Powerindicator Powerindicator In power-saving m ode the device mus t not be disconnected from the m ains supply , as this could othe rwise result in a loss of data. • The indicator lights up green:The device is switched on.
Operation Keyboard Keyboard Keyb oard, Keyboard, Keyb oard, Keyboard, Keyboar d, Alphanumerickey pad Cursorkeys Keys, Func tionkeys Numerickeypad Numerickey pad The illustrated keyboard is an example and may differ f rom the model you use.
Operation Start key Keys, calls up the Windows Start menu. Keys, Menu key calls up the menu for the marked ite m (Windows). Keys, Keys, Shift key enables upper-case letters and the upper key symbols to be displayed. Keys, Alt Gr key produces a character shown on t he bottom right of a key (e.
Operation Anti-theft protec tion Anti-theftprotect ion KensingtonLock MicroSavers 1 2 1 = Kensington Lock 2 = Holes for padlock Y ou can protect your device against theft • with the Kensington Lock device (1) and a K ensington MicroSaver .
Operation Access protection w ith SystemLock (optional) Securityfunctions, Securityfunctions With SystemLock , you can protect your system from unauthorized booting. Then a system ca n only be booted when the user inserts a valid SmartCard in the SmartC ard reader and enters his/her personal identi fi ca tion number (PIN).
T rou bleshooti ng and tips T roubleshooting and tips Refer to the safety notes in the "Safety" manual a nd in the " Getting started", Page 6 cha pter whe n connecting or disconnecting cab les.
T roubleshooting and tips The device cannot be switched off with the ON/OFF switch Cause Remedy The device has not bee n switched on with the ON/OFF switch. ► Press the ON/OFF switch again. System crash ► Ke ep the on/off switch pressed for at least 4 seconds until the machine switche s off.
T rou bleshooti ng and tips Cause Remedy Wrong monitor has been set under Window XP ► Re start the device. ► Press F8 while the system is booting. Either the W indows Advanced Start Options menu or the menu for selecting the operating system appears.
T roubleshooting and tips No mouse pointer displayed on the screen Cause T rou bleshoot ing The mouse is not correctly connected. ► Sh ut down the operating system properly . ► S witch the dev ice off. ► C heck that the mouse cable is properly connected to the system unit.
T rou bleshooti ng and tips Installing new software When installing programs or drivers, import ant fi les may be overwritten and modi fi ed. T o be able to access the original data in th e event of any problems following installation, you should backup y our hard disk prior to installation.
System expansions System expansions Upgrades, Device, Systemexpansi on Components Servicing Repairs to the device must only be carried out by quali fi ed technicians. Unauthorised o pening or incorrect repair m ay greatly e ndanger the user (electric shock, fi re risk) and will invalidate your warranty .
System expansions Information about boards T ake care with the locking mechanisms (ca tche s and centring pins) when you are replacing boards or components on boards. T o prevent damage to the board or th e compo nent s and co nductors on it, please take care when you insert or remove board s.
System expansions Opening the casing Please rea d the relevant safety notes in "Important notes". Disconnect the power plug from of the mains outlet. ► Switch the device off. The device must not be in power-saving mode. ► Remove all cables from the ca sing.
System expansions Closing the casing 2 1 ► Position the upper part of the casing from above in the direction of the arrow (1) onto the lower part of the casing so that the distance to the re ar edge of the casing is approximately 20 mm. ► Push the upper part of the casing in the direction of the arrow (2) until it eng ages.
System expansions Installing a board Do not throw the slot cover away . If you r emove the board aga in, you will need to install the slot cover again (cooling, fi re protection or EMC regulations which need to be complied with). 1 2 ► O pen the casing (see "O pening the casing" , Page 29 ).
System expansions Removing boards ► O pen the casing (see "Ope ning the casing", Page 29 ). 2 1 ► If necessary , unplug any cables which are connected to the b oard. ► Open the retaining clip (1). ► Remove the board out of the casing (2).
System expansions Installing and removing drives The casing can accommodate a total of two drives: • one accessible slim drive (one 5 1/4 inch drive) • one 3 ½-inch hard disk "Accessible drives" are e.g. DVD or CD ROM drives, into which a data medium can be inserted from the outside.
System expansions Installi ng the plastic drive cover Depending on the drive, e.g. if you wish to remove the accessible drive, you may n e e dt or e fi t the plastic drive cover again afterwards. ► Insert the drive cover in t he direction of the arrow into the front panel and press the latches lightly into the corresponding brackets.
System expansions Installing the drive cage Drivecage ► Open the casing (see "Ope ning the c a sing", Pa ge 29 ). 1 2 ► Push the drive cage at an angle into the casing mounts (1). ► If a drive is present, con nect the connector of th e data and power supply cables (2).
System expansions Installi ng an accessible 5 1/4-inch slim drive ► O pen the casing (see "Ope ning the casing", Page 29 ). Do not throw away the covers. If you remove the drive again, you must reinstall the covers (cooling, fi re protection or EMC regulations to be complied with).
System expansions Installing and removing the hard disk drive Removing the hard disk drive ► Open the casing (see "Ope ning the c a sing", Pa ge 29 ). 2 3 3 1 ► Fold up the drive cage (1). ► If there is a drive in the drive cage, disconnect the data and power s upply cables from the drive.
System expansions ► Release the die EasyChange rails from the hard disk. If you do not wa nt to install a new hard disk, keep the EasyChange rails for a future installation. ► C lose the casing (see " Closing t h e casing ", Page 30 ). Installing the hard disk drive ► O pen the casing (see "Ope ning the casing", Page 29 ).
System expansions 1 ► Slide the hard disk together with the EasyChange rails into the bay until you feel the hard disk engage(1). 2 1 1 3 ► Attach the data and the power supply connectors at the hard disk drive (1). ► If necessary also at tach the data cable at the main boa rd.
System expansions Installing and removing a Compact Flash module (optional) Installing the Compact Flash module CompactFlashmodule ► O pen the casing (see "Ope ning the casing", Page 29 ). ► Sw ing up the drive cage. ► If there is a drive in the drive c age, disconnect the data and power supply cables from the drive.
System expansions Removing the Compact Flash module CompactFlashmodule ► Open the casing (see "Ope ning the c a sing", Pa ge 29 ). ► Fold up the drive cage. ► Disconnect the Compact Flash cable connector from the m a inboard. Refer to the manual for the mainboard.
System expansions Installing/removi ng a SmartCard reader (optional) In systems equipped with a SmartCard reader , access can be restricted to those users who have a corresponding SmartCard. Installing th e SmartCard read er SmartCardread er ► O pen the casing (see "Ope ning the casing", Page 29 ).
System expansions Installing and rem oving a WLAN module (optional) WLANmod ule Y ou can also install a WLAN module for wireless LAN (Local Area Network) in the bay of the folded-open drive cage. Installing the WLAN module ► Open the casing (see "Ope ning the c a sing", Pa ge 29 ).
System expansions Removing the WLAN module ► O pen the casing (see "Ope ning the casing", Page 29 ). ► Remove the drive cage (see " Remov ing t he driv e ca ge", Page 34 ). ► D isconnect th e USB cable of the WLAN module from the connector on the mainboard.
System expansions Mainboard expansions More information on how to upgrade the ma in me m ory or the processor of your device are provide d in the manual for the mainboard. Upgrades Lithium batte ry Proces sor Mainmemory Mainboa rd ► Open the casing (see "Ope ning the c a sing", Pa ge 29 ).
System expansions Replacing the lithium battery In order to permanently save the system i nforma tion, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message noti fi es the user when the charge is too low or the battery is empty .
T echnical data T echnical data Electrical data Safety standards complied w ith: IEC 60950, EN 60950, UL 1950, CSA 22.2 No.950 EN55022/B, EN 55024, EN 61000-3-2/3 Protection class: I Rated voltage range 100 V – 240 V Frequency 50 Hz – 60 Hz Max. rated current 2.
Index Index A Access permission, SmartCard 20 Alphanumeric keypa d 18 Anti-theft protection 20 Audio input 1 1 Audio output 1 1 B Battery 46 BIOS Setup 19 BIOS Setup, con fi guration 19 security func.
Index I Important notes 3 Indicators, device 16 Installing, software 14–15 switching on for the fi rs t tim e 14 K Kensington Lock 20 Keyboard 1 8 Keyboard port 1 1 keyboard shortcuts 19 Keyboard s.
Index R Recycling 4 Replacing, lithium battery 46 Replacing, lithium battery 46 Retransportation 3–4 Rubber/plastic feet 8–9 S Safety information 3 Security functions SystemLock 21 Security functi.
Een belangrijk punt na aankoop van elk apparaat Fujitsu ESPRIMO C5730 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Fujitsu ESPRIMO C5730 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Fujitsu ESPRIMO C5730 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Fujitsu ESPRIMO C5730 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Fujitsu ESPRIMO C5730 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Fujitsu ESPRIMO C5730 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Fujitsu ESPRIMO C5730 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Fujitsu ESPRIMO C5730 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
