Gebruiksaanwijzing /service van het product FI-5015C van de fabrikant Fujitsu
Ga naar pagina of 90
P3PC-1592-05ENZ0 Operator's Guide fi-5015C Image Scanner.
fi-5015C Image Scanner Operator’s Guide i CONTENTS ■ Regulatory Information ........................................................ iii ■ Note, Liability ............ ............................................................. v ■ Safety Precautions .
ii Chapter 4 TROUBLES HOOTING ......... .................................. 53 4.1 Error Indications in the Fu nction Number Display ........ 54 4.2 Troubleshooting .... .................................... ....................... 56 APPENDIX A SCANNER SPECI FICATIONS .
fi-5015C Image Scanner Operator’s Guide iii INTRODUCTION Thank you for purcha sing th e fi-5015C Color Scanner. This document describ es how to han dle fi-5015C and basic operation methods. Before you start using fi- 5015C be sure to thoro ughly read this manual to en sure correct use.
iv Canadian DOC Regulations This digital apparatus does not exceed the Class B limit for radi o noise emissions from digital apparatus set out in the Radio interference Re gulations of the Canadian Dep artment of Communications. This Class B digital apparatus complies with Canadian ICES-003.
fi-5015C Image Scanner Operator’s Guide v ■ Note, Liability READ ALL OF THIS MANUAL CAREFULL Y BEFORE USING THIS PRODUCT . IF THIS PRODUCT IS NOT USED CORRECTL Y , UNEXPECTED INJUR Y MA Y BE CAUSED TO USERS OR BYST ANDERS. Also, keep this manual in a safe place so that it can be easily refe rred to during use of this product.
vi How T rademarks Are Indicated In This Manu al References to operating systems (OS) are indicated as follows: Where there is no distinction betw een the dif ferent ve rsions of the abov e operating s ystem, the gen eral term "W indows" is used.
fi-5015C Image Scanner Operator’s Guide vii W arning Indications Used In This Manual Symbols Used In This Manual Screen Examples In This Manual The screen examples in this manual are subject to change without notice in th e interest of product improvement.
viii ■ Safety Precautions In the following warnings, "power cable" may refe r to the AC cable connected to the AC adapter collectively . Do not damage the A C cable . Use only specified A C ca bles and connector cables Use this scanner only at the in dicated po wer v oltage .
fi-5015C Image Scanner Operator’s Guide ix Do not install the de vice in loca tions that has oil smoke, steam, humidity , and dust. T urn the scanner OFF if it is damaged. Do not put liquids inside the sc anner . Do not touch the inside of the scanner unless necessary .
x Do not install the scanne r on unstable surfaces. Do not bloc k the ventilation por ts. Do not place heavy objects or stand on top of the scanner . Firmly i nser t the power plug. A v oid an y contact when scanner is in use. Do not use the scanner immediatel y after mo ving it from a cold place into a warm r oom.
fi-5015C Image Scanner Operator’s Guide xi Bef ore mo ving the scanner , disconnect the power plug fr om the power out let. Pr otect the scanner from static electricity . Disconnect the power plug fr om th e power outl et when the scanner is not used f or a long period of time .
xii.
1 fi-5015C Image Scanner Operator’s Guide 1 Chapter 1 NAME OF P ARTS This chapter shows the exterior view and the name of each part to descrive its fu nction. 1.1 Units .......................................................................... .....
2 1.1 Units 1. Front side Part Function 1. Automatic docu- ment feeder (ADF) Automatically feeds docume nts one by one to the reading position in th e scanner. 2. Side guides Holds the docume nts straight. 3. ADF paper chute Holds the documents to be fed by th e automatic docume nt feeder (ADF).
1.1 Units fi-5015C Image Scanner Operator’s Guide 3 NAME OF P AR TS 1 2. Flatbed 3. Backside Part Function 1. Document holding pad Holds the docume nt on Flatbed. 2. Document bed On which the document is set face down. Part Function 1. USB conn ector Connects USB cable to PC.
4 4. Side (ADF side) Part Function 1. Shipping lock Locks the scanning head to prevent the scanner damaged when movi ng or transporting. 1 Unlocked Locked.
1.2 Operator Panel fi-5015C Image Scanner Operator’s Guide 5 NAME OF P AR TS 1 1.2 Operator Panel Part Function 1. Function button Changes the function activated by [Send to] button. 2. Function number display Indicates the function number or erro r status.
6.
2 fi-5015C Image Scanner Operator’s Guide 7 Chapter 2 BASIC SCANNER OPERA TIONS This chapter describes how to turn On/Off the scanner, and ho w to load/scan the documents. In this chapter Windows XP screenshots are illustrated. The screens and operations may differ slightly if the OS you are using is not Windows XP.
8 2.1 Turning ON/OFF the Scanner 1. Turning the Power On Switch on the Main Power switch located on th e side. Then press [Power] button on the operator Panel.
2.1 Turning ON/OFF the Scanner fi-5015C Image Scanner Operator’s Guide 9 BASIC SCANNER OPERA TIONS 2 2) Double click the "Printer and Other Hardwa re" icon on the Control panel of your PC. ⇒ The [Printer and Other Hardware] window appears.
10 ⇒ The [fi-5015C P roperties] dialog bo x appears. 5) Click the "Device Set" tab. ⇒ The following panel appears. 2. Click [Power Control] button ⇒ The following scre en is displayed.
2.1 Turning ON/OFF the Scanner fi-5015C Image Scanner Operator’s Guide 11 BASIC SCANNER OPERA TIONS 2 3. In this screen, • To power on/off the scanner by p ressing the Power button: ⇒ select "Enable power switch".
12 2.2 Loading Documents on ADF This section explains how to ch eck the document cond ition and load them on ADF. These opera- tions are very importa nt to avoid paper jam or sc anning error. 2.2.1 Checking document condition Check that the document m eets the following condition.
2.2 Loading Do cuments on ADF fi-5015C Image Scanner Operator’s Guide 13 BASIC SCANNER OPERA TIONS 2 • Documents that are not square or rectangular • Very thin documents • Photographs Do not u.
14 HINT When using the ADF, the leadin g edge of all document sheets mu st be evenly aligned. Make sure that curling at the lea ding edge is within the following tolerances: More than 30 m m F eed d i.
2.2 Loading Do cuments on ADF fi-5015C Image Scanner Operator’s Guide 15 BASIC SCANNER OPERA TIONS 2 2.2.2 Loading documents on ADF This section explains how to load documents on ADF . 1. Align the edges of the docu ments. 1) Grasp no more than 50 sheets in a stack.
16 4. Load the documents on the ADF paper chute. 5. Adjust the side guides to the width of t he documents. Move the side guides so that they touch both sid es of the docu ments. If there is any clearance between the side gu ides and the edges of documents, the scanned image may be ske wed.
2.3 Loading Document on Flatbed fi-5015C Image Scanner Operator’s Guide 17 BASIC SCANNER OPERA TIONS 2 2.3 Loading Document on Flatbed 1. Open the docu ment cover.
18 ■ Document Size Orientation of the docume nt an d how to set Paper size shall be as follows for Portrait scan- ning or Landscape scanning . For Flatbed: Minimum 26 (Width ) x 26 (Length) mm (1 x 1 in.) Maximum 216 (Width ) x 297 (Length) mm (8.5 x 11.
2.4 Scanning Documents fi-5015C Image Scanner Operator’s Guide 19 BASIC SCANNER OPERA TIONS 2 2.4 Scanning Documents This section explains how to scan document s using ScandAll PRO as an example. 1. Load documents on the scanner. For details about loading documents, refer to "2 .
20 6. Set the scan type, paper size (see below), etc., an d click the [OK] button. For details on settings in the [TWAIN Driver] dialog box, re fer to "2.5 How to use the Scan- ner Driver" on page 22 ⇒ You are returned to the [Scan Settings] dialog box.
2.4 Scanning Documents fi-5015C Image Scanner Operator’s Guide 21 BASIC SCANNER OPERA TIONS 2 ⇒ The images of scanned docu ments are displayed on the [ScandAll PRO] window. For details on functions and operations of Sc andAll PRO, refer to the description in the [Help] menu.
22 2.5 How to use the Scanner Driver ■ TWAIN Scanner Driver TWAIN Scanner Driver is designed for scanning documents with FUJI TSU image scanner fi series by using application software that complies with the TWAIN standard. The following describes th e procedure with examples of Scan dAll PRO for ordinary scanning by using this driver.
2.5 How to use the Scanner Driver fi-5015C Image Scanner Operator’s Guide 23 BASIC SCANNER OPERA TIONS 2 6) Configure settings for scanni ng and click the [OK] button. For details about the settings on this wi ndow, refer to "Settin g Window for TWAIN Scanner Driver" on page 25.
24 ⇒ The images of scanned documents are disp layed on the [ScandAll PRO] window. With ScandAll PRO, the scanned image will not be displayed when you clear the [Display scanned imag es immediately after scanning] ch eck box in the [Scan Settings] dialog box.
2.5 How to use the Scanner Driver fi-5015C Image Scanner Operator’s Guide 25 BASIC SCANNER OPERA TIONS 2 2. Setting Window for TWAIN Scanner Driver You can set the TWAIN Scanner Driver on this window.
26 Image Mode Specifies the image type for the scanned documents. [Scan] button Starts scanning documents with the current settings. [Preview] button Documents are scanned preliminar ily before the actual scanning. You can confirm th e image of the documents in the preview window.
2.5 How to use the Scanner Driver fi-5015C Image Scanner Operator’s Guide 27 BASIC SCANNER OPERA TIONS 2 [Option...] button You can set up the deta ils of optio nal functions on the window below. [Rotation] tab Select this tab when setting image rotation.
28 ■ ISIS Scanner Driver ISIS Scanner Driver is designed for scanning documents with FUJITSU image scanner fi series by using application software that complies with the ISIS standard. The following describes the procedure with examples of QuickScan for ordinary scanning by using this driver.
2.5 How to use the Scanner Driver fi-5015C Image Scanner Operator’s Guide 29 BASIC SCANNER OPERA TIONS 2 5) Select the profile for scanning. • When creating a new profile Select one from al ready existing prof iles and click [Add Profile...] button.
30 7) Configure settings for scanni ng and click the [OK] button. For details on this dialog bo x, refer to "Configuration Window of ISIS Scanner Driver" on page 31. 8) The [Profile Editor] window appears. Click the [OK] button to return to [New batch] dialog.
2.5 How to use the Scanner Driver fi-5015C Image Scanner Operator’s Guide 31 BASIC SCANNER OPERA TIONS 2 2. Configuration Wind ow of ISIS Scanner Driver "Main" tab Mode Selects a color mode suitable for the purpose from the menu. Dots per inch Specifies the number of pixels (dots) per inch.
32 Brightness Sets the brightness of the entire image. Spec ify the brightness as a number within the range of 1 (dark) to 128 (bright). To brighten the entire image, inc rease the value of the setting. To darken the enti re image, decrease the value.
2.5 How to use the Scanner Driver fi-5015C Image Scanner Operator’s Guide 33 BASIC SCANNER OPERA TIONS 2 [Scan Area...] button Opens the Scan Area dialog box. Speci fy scan area for the document size. The size can be set by dragging the frame w ith mouse.
34 "More" tab Opens [More Settings] window. Used for setting advanced features. Use Advanced DTC This option scans any kind of documents by binary processing to produce data with good scanning quality.
2.5 How to use the Scanner Driver fi-5015C Image Scanner Operator’s Guide 35 BASIC SCANNER OPERA TIONS 2 "Gamma" tab Download You can download and use any Gamma pattern. Custom You can specify the numeric values of items such as “Gamma”, “Brightness”, “Con- trast”.
36 2.6 Image Scanning Application This section explains about the bundled "Scand All PRO" image scanning application, which is used as an example to explain the procedures in this manual. ScandAll PRO supports both TWAIN and ISIS drivers. By defining scan settings as profiles, you can customize the settings according to your preference.
3 fi-5015C Image Scanner Operator’s Guide 37 Chapter 3 MAINTENANCE This chapter describes how to clear the paper jam, perform daily main tenance and cleaning. Do not use aer osol spra ys near the scanner Do not use any aerosol sprays or alcohol based spra ys to clean the scanner .
38 3.1 How to clear the paper jam When a paper jam occurs while using ADF, follow the procedure below to remove jammed paper. 1) Remove the documents from the ADF paper chute. 2) Open the AD F. . 3) Remove the jam med paper. 4) Close the ADF completely until it clicks.
3.2 Cleaning fi-5015C Image Scanner Operator’s Guide 39 MAINTENANCE 3 3.2 Cleaning To keep scanner performance stable, clean the scanner and re place the consumable if necessary as follows. 3.2.1 Cleaning Materials For details about the cleaning ma terials, contact the FUJITSU scanner dealer where you pur- chased the scanner.
40 3.2.2 Cleaning the Flatbed ■ Cleaning Method 1. Open the docu ment cover. 2. Clean the following locations usin g a so ft, dry cloth moistened with cleaning fluid. • Document holdin g pad - 1 Wipe gently. • Document bed - 2 Wipe lightly. 3. Wait for cleaned parts to dry.
3.2 Cleaning fi-5015C Image Scanner Operator’s Guide 41 MAINTENANCE 3 3.2.3 Cleaning the ADF Clean the ADF every 1,000 scans. Note that this guideline varies accordi ng to the type of documents you are scanning.
42 • Pad ASSY Wipe Pad ASSY with the cloth in the direction from bottom to top. • Pick roller unit Wipe the Pick roller unit by moving the cloth from side to side of rollers. Rotate the rollers forward with your finger and repeat the wipin g procedure until all surface of ro ller are cleaned.
3.2 Cleaning fi-5015C Image Scanner Operator’s Guide 43 MAINTENANCE 3 4. Open the Flatbed cover and clean th e following locations. ATTENTION The glass surface under the ADF become s hot during the oper ation of the scanner.
44 3.3 Replacing Consumable 3.3.1 Part number and Replacement cycle The following table lists the consum able used in the scanner. Be su re to keep some consumables in stock. The customer is required to replace consumable periodic ally. Otherwise, the scanner may not func- tion properly.
3.3 Replacing Consumable fi-5015C Image Scanner Operator’s Guide 45 MAINTENANCE 3 3.3.2 Guidelines for Cons umable Replacement Cycle With this product, you can le arn how many times the consumab les are used so that you can estimate the right timing for the replacement.
46 ⇒ The [fi-5015C Properties] dialog box appears. 5. Click the "Devi ce Set" tab. ⇒ The following panel appears. You can confirm the following information on this panel: • Total number of scans with ADF and Flatbed.
3.3 Replacing Consumable fi-5015C Image Scanner Operator’s Guide 47 MAINTENANCE 3 The following message may appear while using the scanner: Replace consumables when this message is displayed. After clicking the [Ignore] button, this messa ge will disappea r and scanning will continue .
48 3. Remove the snap-in Pad ASSY by pinching the upper part of the pad clamp as shown in the following photo. 4. Install new Pad ASSY by the revers e procedure of removing. 5. Press the center of the ADF to close it until it clicks. 6. Reset the pad cou nter.
3.3 Replacing Consumable fi-5015C Image Scanner Operator’s Guide 49 MAINTENANCE 3 4) Click the "Device Set" tab. 5) After clicking the [Clear] button beside "P ad" in "Page Counter", click the [OK] button. ⇒ The following wind ow appears.
50 3.3.4 Replacing the Pick roller unit 1. Remove all documents from the ADF pape r chute. 2. Open the ADF. 3. Remo ve the Pick ro ller unit from the scanner. 1) Pinch the fixture with your fi ngers with another hand holding the Pick roller unit. Be careful, the ADF may close and pinch your fingers.
3.3 Replacing Consumable fi-5015C Image Scanner Operator’s Guide 51 MAINTENANCE 3 2) Pull the Pick roller unit to the fixture‘s side. ⇒ The Pick roller unit is removed downward s. 4. Attach a new Pick roller unit to the sca nner. Attatch a new Pick roller unit to the scanner in reverse order of removing.
52 5. Press the center of the ADF to close it until it clicks. 6. Reset the Pick roller counter. 1) Check that the scanner is connected to your PC and turn on the scanner. 2) Open the [Scanners and Cameras] from the control panel of your PC. 3) Open the [Properties] of [fi-501 5C] from the [Scanners and Cameras].
4 fi-5015C Image Scanner Operator’s Guide 53 Chapter 4 TROUBLESHOOTING This chapter describes how to remedy tro ubles and items to check before contacting the agent where you bought the scanner. 4.1 Error Indications in the Function Number Display .
54 4.1 Error Indications in the Function Number Display When any error occurs, the operat or panel indicates "U" followed by a number alternately for tem- porary errors, or "E" followed by a numb er for device alarms (permanent error).
4.1 Error Indications in t he Function Number Display fi-5015C Image Scanner Operator’s Guide 55 TR OUBLESHOO TING 4 ■ Device alarms: A number appearing in alternation following the "E" refers to th e follo wing type of device alarms: Indication Meaning Solution E0 Shipping lock error occurred.
56 4.2 Troubleshooting If a problem occurs, check the following items befo re contacting the manufacturer's authorized ser- vice center. Be careful, the inside of ADF (automatic document feeder) may become hot during th e operation. Symptom Check this item Remedy Scanner does not turn on.
4.2 Troubleshooting fi-5015C Image Scanner Operator’s Guide 57 TR OUBLESHOO TING 4 * "Multi feed" means that more than 2 papers are fed at the same time. Multi feed* frequently occurs. Does the document satisfy the "Doc- ument Quality" described in Section 2.
58.
fi-5015C Image Scanner Operator’s Guide AP-1 A APPENDIX A SCANNER SPECIFICA TIONS ■ Basic Specifications Item Specifications Dimension (mm) Width Depth Height 328 (12.
AP-2 ■ Dimensions Unit: millimeters 175 447 (17.6 in.) (6.88 in.) 175 328 (12.9 in .) (6.88 in.).
fi-5015C Image Scanner Operator’s Guide AP-3 B APPENDIX B Using [Scan] or [Send to] button ■ Settings on the Personal Computer By setting the link of the application software to t h e [Scan] or [Send to] button, yo u can launch the linked application b y si mply pushing the button.
AP-4 5. Select the application with its process, excuted by th e event. For the case of Windows XP, click [Start this program] under [Acti ons] and select the application and process from the menu. 6. Click the [OK] button. If you are using ScandAll PRO, refer to "ScandAll PRO V2.
fi-5015C Image Scanner Operator’s Guide AP-5 B ■ Settings on the Scanner • To use the [SCAN] button : You can use this button as is; no special settings are required.
AP-6.
fi-5015C Image Scanner Operator’s Guide AP-7 C APPENDIX C GLOSSARY OF TERMS A4 size A standard p aper size. Paper size is 210 x 297 mm. A5 size A standard p aper size. Paper size is 148 x 210 mm. A6 size A standard p aper size. Paper size is 105 x 148 mm.
AP-8 A utomatic siz e/skew detection A function that automatically detect s the doc ument s' pag e size and adjust s output dat a to the detected page size.
fi-5015C Image Scanner Operator’s Guide AP-9 C Default settings Pre-set values for optional menus. Density In this manual, refers to a me asurement of the depth of the display . Dither The process by which a group o f dots is ar ranged to represent a sha de of gray .
AP-10 Equipment Erro r An error that cannot be fixed by the op erator . The operator should call the manufa cturer for service. Err or diffusion High-quality half tone (pseudo-g rayscale) image production based on black-and-wh ite pixel binarization.
fi-5015C Image Scanner Operator’s Guide AP-11 C Flatbed An input device of the scanner , where documents are placed and scan ned. Generally used for scanning pages out of a book, or p aper th at is out of the feeding specification of the ADF . Also used to scan a small volume of document s by manual operation.
AP-12 IPC preset mode While reading binary images, it is necessary to set th e scanner according to the quality of the sheet to be read. In this mode, these settings can be performed in advance by cor- responding each setting to a p attern number .
fi-5015C Image Scanner Operator’s Guide AP-13 C Mirr or image The read image is symmetrica lly flipped to produce a mirror image o f the original detected in the main scanning d irection. Moire P atterns Recurrent pattern s on scanned images caused by incorrect settings of angle s.
AP-14 Photograph mode (White level f o llower OFF) Selecting photograph mode makes brightness and contrast settings e ffective but pre- vents the threshold from bein g set. With photograph mode, the darkness of image corre- sponds to the black-pixel density , making it suitable in scanning ima ges such as photographs having gradations.
fi-5015C Image Scanner Operator’s Guide AP-15 C Separation r oller A roller that separa tes the sheet s of pap er from each other . Simplex reading mode A mode for scanning only the front side o f the document. Smoothing A process that eliminates "jaggies" from sl anted lines and curves.
AP-16 TW AIN (T echnology Without An y Interesting Name) A standard for API (App lication Program Interf ace) or proto col fo r imaging devices (scan- ners, digital camera s, etc.) developed by TW AIN Working Group. In order to use devices that comply with this st andard, it is necessary to inst all driver software based on the same standard.
fi-5015C Image Scanner Operator’s Guide IN-1 INDEX A ADF (automatic document feeder) ............ 2 C Checking document condition ................. 12 Cleaning Materials .................................. 39 Cleaner F1 ..............................
IN-2 U USB connector .............................. ............ 3 Using the (Scan) or (Send to) button ....... . 3.
z The contents of this manual are subject to change without notice. z PFU LIMITED is not liable whatso ever for any damages resulting from the use of this scanner a nd procedures described in this manual, profit loss due to defects, and any claims by a third party.
Een belangrijk punt na aankoop van elk apparaat Fujitsu FI-5015C (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Fujitsu FI-5015C heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Fujitsu FI-5015C vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Fujitsu FI-5015C leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Fujitsu FI-5015C krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Fujitsu FI-5015C bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Fujitsu FI-5015C kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Fujitsu FI-5015C . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
