Gebruiksaanwijzing /service van het product ZBD6880K van de fabrikant GE Monogram
Ga naar pagina of 16
If you have questions , call 800.626.2000 or visit our website at: www .monogram.com Monogram. ® Installation Instructions Built-In Dishwashers ZBD6800K ZBD6880K ZBD6890K* Design Guide with Installation Instructions * For ZBD6890 Series also refer to the instructions provided on the template packed with that model.
Safety Information 2 CONTENTS Installation Preparation Parts Supplied ..............................................................................3 Materials Y ou Will Need ............................................................3 T ools Y ou Will Need .
TOOLS YOU WILL NEED: Phillips head screwdriver 5/16" and 1/4" nutdriver 6" Adjustable wrench Level Carpenters square Measuring tape Safety glasses Flashl.
PREP ARE DISHW ASHER ENCLOSURE • The rough cabinet opening must be at least 24" deep, 24" wide and approximately 34-1/2" high from floor to underside of the countertop.
DRAIN REQUIREMENTS • Follow local codes and ordinances. • Do not exceed 10 feet distance to drain. • Do not connect drain lines from other devices to the dishwasher drain hose. NOTE: This dishwasher is equipped with a high drain loop. There is no minimum height required for drain hose routing.
6 Installation Preparation PREP ARE ELECTRICAL WIRING W ARNING FOR PERSONAL SAFETY : Remove house fuse or open circuit breaker before beginning installation.
PREP ARE HOT W A TER LINE • The line may enter from either side, rear or floor within the shaded area shown in Figure F . • The line may pass through the same hole as the electrical cable and drain hose. Or , cut an additional 1-1/2" dia. hole to accommodate the water line.
REMOVE WOOD BASE, INST ALL LEVELING LEGS IMPOR T ANT — Do not kick off wood base! Damage will occur . • Move the dishwasher close to the installation location and lay it on its back. • Remove the four leveling legs on the underside of the wood base with an adjustable wrench or 15/16" socket.
Drain Outlet Hose Clamp Shoulder Stop INST ALL TRIM PIECES Skip this step if trim is not supplied with the dishwasher . • Locate trim strips inside dishwasher . • Press trim onto the tub flange on each side. Start with the top edge, pressing on as you move towards the bottom.
POSITION DISHW ASHER UNDER COUNTERTOP STEP 10 10 • Push the dishwasher into the cabinet. • Push at the sides with your hands. Do not use your knee against the door since door damage will occur . • Check that the tub insulation blanket does not get “ bunched-up ” or interfere with the springs as you slide it into the cabinet.
LEVEL DISHW ASHER IMPOR T ANT — Dishwasher must be level for proper dish rack operation and wash performance. • Place level on door and rack track inside the tub as shown to check that the dishwasher is level. • Level the dishwasher by adjusting the four leveling legs individually .
CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES AND ORDINANCES. The drain hose molded end will fit 5/8" or 1" diameter connections on the air gap, waste tee or disposer . Cut on the marked line as required for your installation. • If a longer drain hose is required, add up to 42" of length for a total of 10 ft.
13 Installation Instructions PRE-TEST CHECK LIST Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your warranty . Check to be sure power is OFF . Open door and remove all foam and paper packaging.
REPLACE TOEKICK • Place toekick against the legs of the dishwasher . • Align the toekick with the bottom edge and make sure it is against the floor . • Insert and tighten the two toekick attachment screws. The toekick should stay in contact with the floor .
Custom Panel Dimensions 15 CUSTOM P ANEL FOR MODEL ZBD6890 This dishwasher requires a field installed 3/4" thick custom panel and custom handle. An installation template is packed with these models and may be obtained in advance. Order Pub. No. 31-30569.
Pub. No. 31-30568 Part No. 206C1559P108 12-03 JR NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local ser vice in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric.
Een belangrijk punt na aankoop van elk apparaat GE Monogram ZBD6880K (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen GE Monogram ZBD6880K heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens GE Monogram ZBD6880K vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding GE Monogram ZBD6880K leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over GE Monogram ZBD6880K krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van GE Monogram ZBD6880K bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de GE Monogram ZBD6880K kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met GE Monogram ZBD6880K . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
