Gebruiksaanwijzing /service van het product ZISB42D van de fabrikant GE Monogram
Ga naar pagina of 48
GE Monogram ® 42" Built-In Refrigerators Custom Options Guide and Installation Instr uctions With Custom Panel Dimensions and Trim Kit Installation Instructions Models: ZIS42N ZISW42D ZISB42D These Monogram built-in refrigerators are designed to be customized with decorator door and grille panels.
WARNING WARNING • Il ne faut utiliser cet appareil que pour l’usage pour lequel il a été construit. • Il faut réparer ou remplacer immédiatement tout cordon d’alimentation électrique effiloché ou endommagé. • Débrancher le réfrigérateur avant le nettoyage ou toute intervention.
3 DESIGN INFORMATION Design Infor mation 42" Built-In Refrigerator Flush or Semi-Flush Enclosure Installations Side Panel Requirements: • Side panels are not required whenever the refrigerator is installed into an enclosure or between pantry and oven cabinets.
4 DESIGN INFORMATION Design Infor mation 42" Built-In Refrigerators Installation At End-of-Run Frameless Cabinets Note: 1/2" thick side panels shown. Side panels can be any thickness. Add side panel thickness to outside trim width (42") to calculate the rough-in dimension.
5 DESIGN INFORMATION Design Infor mation 42" Built-In Refrigerator 1/4" and 3/4" panels with standard handles. No trim kits required. 3/4" Custom panels with Tubular Stainless Steel handles and custom dispenser collar. Trim Kits ZKHTSS1, ZKT42 & ZWCD1.
6 Custom Panel Dimensions 42" Built-In Refrigerator ZIS42N (Non-dispenser) Design Information Cutout dimensions, clearances and side panel sizes are determined by the many installation options available. Side panels must be used whenever the sides of the refrigerator will be exposed.
7 Custom Panel Dimensions 42" Built-In Refrigerator ZIS42N (non-dispenser) Standard T rim with 1/4" Panels • 1/4" Panels: Cut panels to size. • Custom handles with 1/4" door panels require T rim Kit ZKH1 (or ZKHSS1 for tubular -stainless steel handles).
8 Custom Panel Dimensions 42" Built-In Refrigerator Custom Door Panel Dimensions Using T rim Kit ZKT42 3/4" thick panel with standard handle Grille Panel height can vary to fill installation height.
9 Custom Panel Dimensions 42" Built-In Refrigerator ZIS42N (non-dispenser) • ZKT42 and ZKHT1 installed together provides for the installation of 3/4" custom door and grille panels, using a custom handle, of your choice. Order ZKHTSS1 for tubular stainless-steel handles.
10 Custom Panel Dimensions 42" Built-In Refrigerator *42" Min. for a flush installation into an enclosure. *41-1/2" Min. for a semi-flush installation into an enclosure. Note: Additional cutout width may be required when side panels are used.
11 Custom Panel Dimensions 42" Built-In Refrigerator ZISW42D (white dispenser) ZISB42D (black dispenser) Standard T rim with 1/4" Panels • 1/4" Panels: Cut panels to size. • Custom handles with 1/4" door panels require T rim Kit ZKH1.
12 Custom Panel Dimensions 42" Built-In Refrigerator ZISW42D (white dispenser) ZISB42D (black dispenser) • The ZKT42 trim kit provides for the installation of 3/4" custom door and grille panels, using the standard full- length handle. Cut panels to size and install.
13 Custom Panel Dimensions 42" Built-In Refrigerator Custom Door Panel Dimensions Using T rim Kit ZKT42 3/4" thick panel with custom handle and/or ZWCD1 custom collar trim Detail B Rout panels to specification below on the handle side of each panel Important: Maintain 1-1/2" min.
14 Custom Panel Dimensions 42" Built-In Refrigerator For All Monogram Built-In Refrigerators Side Panel or Filler Options (not to scale) Side panels must be used whenever the sides of the refrigerator will be exposed. 1/4" Side Panels Insert end of side panel into trim.
15 Installation 42" Built-In Refrigerator Tools Required • T insnips to cut banding • Stepladder • 1-1/2" open-end wrench • Bucket • Level • Appliance Hand T ruck • T ubing cut.
16 Installation 42" Built-In Refrigerator Step 1 Remove Packaging Step 2 Install Water Line PRODUCT INSTALLATION • Remove outer carton. – Carefully cut banding at the top and bottom. • Slide out back corner posts (2). • Slide carton off top of cabinet.
17 Installation 42" Built-In Refrigerator PRODUCT INSTALLATION Step 3 Install Side Panels • Side panels are not required when the refrigerator is installed into an enclosure.
Installation 42" Built-In Refrigerator 18 PRODUCT INSTALLATION Step 4 Roll Refrigerator Into Opening Step 5 Level Refrigerator • Gently push refrigerator into opening with hands against front corners. The cardboard protective pad should be beneath the refrigerator .
19 Installation 42" Built-In Refrigerator Step 7 OPTION 1 Secure refrigerator at the top T o prevent the refrigerator from tipping over , you must: • Install a wood block, the full width of the refrigerator . Secure the block with wood screws penetrating at least 3/4" into wall studs.
Installation 42" Built-In Refrigerator 20 Step 9 Connect power • Connect refrigerator power cord plug to properly grounded receptacle, accessible through the top right side of the grille opening. • Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on.
21 ZKH1 T rim Kit (For 1/4" Panels) Support for Custom Handles OPTION 1 For non-dispenser model or dispenser model using custom collar trim Step 1 Remove handles Kit contents Parts List: A. Fresh food door extrusion B. Freezer door extrusion for non- dispenser model and dispenser model using custom collar .
• Again, with both doors closed, check the location of the centerlines to be sure they are parallel to the edge of the door , and level with opposite door . • Drill 1 /16" pilot hole through the panel until it starts into the aluminum extrusion.
Step 3 Assemble panel, extrusion and handle Extrusion 3/4" Min. 1-1/2" Max. Handle Decorator Door Panel ZKH1 T rim Kit (For 1/4" Panels) Support for Custom Handles Option 1 Installation • Remove the door extrusions and door panels. • Drill 1/16" pilot hole through extrusion.
24 ZKH1 T rim Kit (For 1/4" Panels) Support for Custom Handles OPTION 2 For dispenser model using full-width trim Step 1 Remove handles • Open door to 90 ° . Remove the screws from the full-length aluminum handle of the freezer door . • Retain screws, discard handle.
ZKH1 T rim Kit (For 1/4" Panels) Support for Custom Handles Handle Bracket Handle Bracket Custom Handle Dispenser Trim Dispenser Trim Option 2 Installation Step 4 Install custom handle Step 5 Mount assembled dispenser trim • Drill clearance holes through the handle bracket and the dispenser trim.
ZG2 T rim Kit Grille Panel Frame Adjustment 26 FOR 83", 83-1/2" AND 84-1/2" INSTALLATION HEIGHTS • This kit provides optional side trim pieces for the original grille frame to fit 83", 83-1/2" or 84-1/2" installation heights.
27 ZKT42 T rim Kit 3/4" Custom Panels G A B E F J I H C D T ools and materials required: • #2 Phillips screwdriver • Stubby Phillips screwdriver • Drill and appropriate bits • Safety glasses • Custom panels Parts List: Freezer Door A. T op trim B.
28 Note: If a custom collar is to be used, order ZWCD1 trim kit. If a custom handle is to be used, order ZKHT1 trim kit. Important: When the bottom trim piece is removed, an aluminum shim secured to the bottom of the door can be seen. Do not attempt to remove this piece.
29 ZKT42 T rim Kit 3/4" Custom Panels ZKT42 – Install 17 screws • Secure support brackets to the bottom of the panels with #4 screws provided.
The refrigerator is shipped with the top case trim secured at the 83" refrigerator height. • Loosen 2 screws on both sides and raise the top case trim to meet soffit height, from 83" to 84-1/2". • T ighten all 4 screws. • Secure the new grille panel support to the back side of the 3/4" panel with #6 screws.
31 ZKT42 T rim Kit 3/4" Custom Panels Dimension B ZKT42–6-3/4" Dimension A ZKT42–4-3/8" Dimension C ZKT42–4-3/8 " • Position and mark the location for the support brackets on the back side of the panels. Align all brackets flush with the end of the panels, with tabs protruding over the edge.
32 • Place the upper panel onto the top of the dispenser with tabs inserted into the slots. • Push the panel back against the steel door . • Open door and install screws through the back of the trim and into the panel, at the top and hinge side.
33 ZKHT1 T rim Kit (For 3/4" Panels) Support for Custom Handles These instructions are divided into 2 options: Option 1—For non-dispenser and dispenser models using custom collar trim. Option 2—For dispenser model using the standard full-width trim.
• Secure the panel to the trim temporarily by driving 2 screws through the back side of the trim at the top. • Slide door extrusion in between panel and steel door . T emporarily secure with 2 screws. • Drill 1⁄16" pilot hole through the panel until it starts into the aluminum extrusion.
35 ZKHT1 T rim Kit (For 3/4" Panels) Support for Custom Handles Option 1 Installation Step 3 Assemble panel, extrusion and handle Step 4 Mount assembled panels • Remove the door extrusions and door panels. • Drill 1/16" pilot hole through extrusion.
Note: Optimal final appearance depends on careful routing depth. Do not exceed 1 ⁄ 4" routing depth. • Position the handle bracket onto the steel door by matching existing screw holes on the door and bracket. • Re-install dispenser trim, temporarily .
37 ZKHT1 T rim Kit (For 3/4" Panels) Support for Custom Handles • Drill clearance holes through the handle bracket and the dispenser trim. • Install screw(s) long enough to pass through the handle bracket, dispenser trim and into the custom handle.
38 This kit provides for the installation of Stainless Steel custom handles on 1/4" thick decorator door panels. The door extru- sions allow these custom handles to be secured to the door structure, rather than to the custom panels. This kit contains all the necessary parts for dispenser and non-dispenser models.
39 ZKHSS1 for 1/4" Panels Tubular Stainless Steel Handles Step 2: Match Handle Extrusions to Handle • Cut a piece of corrugated to use as a pad to protect the panel finish. Use 1/2" thick section of plywood to protect flooring when drilling.
40 ZKHSS1 for 1/4" Panels Tubular Stainless Steel Handles Step 3: Install Standoffs onto Handles • Place a handle standoff on each attachment post along the handle. Position the set screw hole on each standoff to point to the floor . • Install set screws into the bottom of each standoff, using the Allen wrench provided.
41 ZKHSS1 for 1/4" Panels Tubular Stainless Steel Handles Raised Panel on 1/4" Thick Backing: A raised panel design secured to a 1/4" thick backing (screwed or glued) can be used with this handle kit. • Cut the 1/4" thick panels to size.
42 ZKHTSS1 for 3/4" Panels Tubulor Stainless Steel Handles This kit provides for the installation of Stainless Steel custom handles on 3/4" thick decorator door panels. The door extrusions allow these custom handles to be secured to the door structure, rather than to the custom panels.
43 ZKHTSS1 for 3/4" Panels Tubulor Stainless Steel Handles Step 2: Match Handle Extrusions to Panels • Cut a piece of corrugated to use as a pad to protect the panel finish. Use 1/2" thick section of plywood to protect flooring when drilling.
44 ZKHTSS1 for 3/4" panels Tubular Stainless Steel Handles Step 3: Install Standoffs onto Handles • Place a handle standoff on each attachment post along the handle. Position the screw hole on the standoff to point to the floor . • Install set screws into the bottom of each standoff, using the Allen wrench provided.
45 ZKHTSS1 for 3/4" Panels Tubular Stainless Steel Handles For models with full width dispenser trim and 2 piece freezer panels: It is best that 2 people perform this step. • Carefully , lift the assembled panel to the case trim. Hold both panels so they do not twist the extrustion.
46 ZWCD1 T rim Kit Custom Dispenser Collar B C D A • 3/4" thick panels using optional custom handles. Select the panel size accordingly . Parts List: A.
47 ZWCD1 T rim Kit Custom Dispenser Collar Note: 1/4" door panels do not require routing. • Secure top and bottom brackets to the dispenser , using the screws previously removed. • Install the custom panels according to the appropriate installation instructions.
Note: While performing installations described in this book, safety glasses or goggles should be worn. To obtain specific information concerning any Monogram product or service, call GE Answer Center ® consumer information service at 800.626.2000–any time, day or night.
Een belangrijk punt na aankoop van elk apparaat GE Monogram ZISB42D (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen GE Monogram ZISB42D heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens GE Monogram ZISB42D vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding GE Monogram ZISB42D leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over GE Monogram ZISB42D krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van GE Monogram ZISB42D bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de GE Monogram ZISB42D kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met GE Monogram ZISB42D . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
