NL
GE logo
Officiële handleiding

GE PBe

34 pagina's·2.2 MB·Switch·PDF·EN
GE PBe
Inhoudsopgave 53 secties Introduction · Conventions used in this document · Safety terms and symbols · Overview · … TonenVerbergen
Introductionp.5Conventions used in this documentp.6Safety terms and symbolsp.6Overviewp.7Compatibilityp.7Disclaimerp.7Product contentsp.8Figure 1. Product contentsp.8Other required equipmentp.8Installation environmentp.9Power specificationsp.9Installationp.11PBe componentsp.11Figure 2. PBe landmarksp.11Typical system layoutp.12Figure 3. Multiple ATM system layoutp.12Installation overviewp.13Required informationp.13Required DIP switch informationp.14Table 1. Important switch assignmentsp.14Table 2. Default switch settingsp.14Installation stepsp.14Programmingp.16HyperTerminal configurationp.16Figure 4. Laptop connected to PBep.17Figure 5. HyperTerminal programming modep.18Figure 6. Main menup.18Figure 7. The PBe Set-up menup.19Figure 8. The terminal IP/camera set-up menup.20Figure 9. The camera/terminal IP tablep.21Manual DIP switch configurationp.22DIP switch settingsp.24SW1 switches 1 to 4p.24Table 3. SW1 switches 1 to 4 - monitor modep.24SW1 switches 5 to 8p.25Table 4. SW1 switches 5 to 8 - Camera number selectionp.25SW3 switches 1 to 8p.26Table 5. SW3 switches 1 to 8 - Device typep.26SW4 switches 7 and 8p.26Table 6. SW4 switches 7 and 8 - communication protocolp.26Accessing the Webserverp.27Figure 10. The PBe home pagep.28Troubleshootingp.29Table 7. Troubleshooting tablep.29Technical specificationsp.30PBep.30Cable Specificationsp.31Figure 11. 4310-0034B cablep.31Figure 12. 4310-0061 cablep.32Figure 13. 4310-0040 PBe Ethernetp.33Contacting technical supportp.34Table 8. Sales and support contact informationp.34Online publication libraryp.34
Page 1 of the GE PBe user manual
Pagina 1 · klik om te vergroten
Pagina 1
GE PBe diagram (page 1)
Afb. 1
Page 2 of the GE PBe user manual
Pagina 2 · klik om te vergroten
Pagina 2

ATM ProBridge User Manual ii

Copyright Copyright © 2006, GE Security Inc. All rights reserved.

This document may not be copied or otherwise reproduced, in whole or in part, except as specifically permitted under US and international copyright law, without the prior written consent from GE.

Document number/ 0150-0315A (March 2006).

Disclaimer THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. GE ASSUMES NO RESPONSIBILITY FOR INACCURACIES OR OMISSIONS AND SPECIFICALLY DISCLAIMS ANY LIABILITIES, LOSSES, OR RISKS, PERSONAL OR OTHERWISE, INCURRED AS A CONSEQUENCE, DIRECTLY OR INDIRECTLY, OF THE USE OR APPLICATION OF ANY OF THE CONTENTS OF THIS DOCUMENT. FOR THE LATEST DOCUMENTATION, CONTACT YOUR LOCAL SUPPLIER OR VISIT US ONLINE AT WWW.GESECURITY.COM

This publication may contain examples of screen captures and reports used in daily operations. Examples may include fictitious names of individuals and companies. Any similarity to names and addresses of actual businesses or persons is entirely coincidental.

GE and the GE monogram are registered trademarks of General Electric. PBe product and logo are trademarks of GE Security.

Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.

Intended use Use this product only for the purpose it was designed for; refer to the data sheet and user documentation. For the latest product information, contact your local supplier or visit us online at www.gesecurity.com

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful inter- ference to radio communications.

You are cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

R Operation of this equipment in a residential area may cause inter- ference, in which case the user is required to take all measures that are necessary, at the user's expense, to correct the interference

Trademarks and patents · FCC compliance · Regulatory

Page 3 of the GE PBe user manual — Table of contents
Pagina 3 · klik om te vergroten
Pagina 3

Table of contents

Introductionp.5Conventions used in this documentp.6Safety terms and symbolsp.6Overviewp.7Compatibilityp.7Disclaimerp.7Product contentsp.8Figure 1. Product contentsp.8Other required equipmentp.8Installation environmentp.9Power specificationsp.9Installationp.11PBe componentsp.11Figure 2. PBe landmarksp.11Typical system layoutp.12Figure 3. Multiple ATM system layoutp.12Installation overviewp.13Required informationp.13Required DIP switch informationp.14Table 1. Important switch assignmentsp.14Table 2. Default switch settingsp.14Installation stepsp.14Programmingp.16HyperTerminal configurationp.16Figure 4. Laptop connected to PBep.17Figure 5. HyperTerminal programming modep.18Figure 6. Main menup.18Figure 7. The PBe Set-up menup.19Figure 8. The terminal IP/camera set-up menup.20Figure 9. The camera/terminal IP tablep.21Manual DIP switch configurationp.22DIP switch settingsp.24SW1 switches 1 to 4p.24Table 3. SW1 switches 1 to 4 - monitor modep.24SW1 switches 5 to 8p.25Table 4. SW1 switches 5 to 8 - Camera number selectionp.25SW3 switches 1 to 8p.26Table 5. SW3 switches 1 to 8 - Device typep.26SW4 switches 7 and 8p.26Table 6. SW4 switches 7 and 8 - communication protocolp.26Accessing the Webserverp.27Figure 10. The PBe home pagep.28Troubleshootingp.29Table 7. Troubleshooting tablep.29Technical specificationsp.30PBep.30Cable Specificationsp.31Figure 11. 4310-0034B cablep.31Figure 12. 4310-0061 cablep.32Figure 13. 4310-0040 PBe Ethernetp.33Contacting technical supportp.34Table 8. Sales and support contact informationp.34Online publication libraryp.34
Page 4 of the GE PBe user manual
Pagina 4 · klik om te vergroten
Pagina 4

ProBridge Ethernet User Manual iv

Page 5 of the GE PBe user manual — Introduction
Pagina 5 · klik om te vergroten
Pagina 5

Introduction

This is the GE ProBridge Ethernet User Manual for model PBe. This document includes detailed instructions explaining:

  • how to setup and install the PBe ProBridge and
  • how to connect to single or multiple ATM sites.

There is also information describing how to contact technical support if you have questions. To use this document effectively, you should meet the following minimum qualifications:

  • a basic knowledge of CCTV systems and components; and
  • a basic knowledge of electrical wiring and low-voltage electrical connections.

Read these instructions and all ancillary documentation entirely before installing or operating this product.

Page 6 of the GE PBe user manual — Safety terms and symbols
Pagina 6 · klik om te vergroten
Pagina 6

Conventions used in this document

The following conventions are used in this document:

BoldMenu items and buttons. ItalicEmphasis of an instruction or point; special terms. File names, path names, windows, panes, tabs, fields, variables, and other GUI elements. Titles of books and various documents. Blue italic(Electronic version.) Hyperlinks to cross-references, related topics, and URL addresses. MonospaceText that displays on the computer screen. Programming or coding sequences.

Safety terms and symbols

These terms may appear in this manual:

Page 7 of the GE PBe user manual — Disclaimer
Pagina 7 · klik om te vergroten
Pagina 7

Overview

The PBe is a specific ProBridge unit for interfacing the DVR family of digital video multiplex/recorders to financial institution automated teller machines (ATMs). The PBe supports Ethernet network communications.

Compatibility

The PBe is compatible with all of the following DVR products:

  • DVMRe, version 3.07 and above.
  • DVMR-eZ, version 3.20 and above.
  • Triplex, version 4.00 and above.
  • Triplex-eZ, version 4.03 and above.
  • WaveReader, version 3.6 and above.

Disclaimer

The PBe components identified within this document provide means of capturing transaction data for use by the DVR family of digital video recording/transmission products. The PBe components translate the data into a usable format by the DVR and permits associating transaction data with specific cameras. GE assumes no responsibility for the amount and type of information available, the operation, non-operation, or erroneous operation of these third-party transaction products.

Page 8 of the GE PBe user manual — Other required equipment
Pagina 8 · klik om te vergroten
Pagina 8

Product contents

The PBe system consists of the ProBridge unit, this manual, an Ethernet cable, a PBe to DVR cable, a PBe to PC cable, and a power supply, as shown in Figure 1.

Figure 1. Product contents

4310-0034B PB3 to DVR cable

GE PBe — Product contents diagram (page 8)
Afb. 2 · Product contents

0150-0315 ProBridge Manual 4310-0061A PBe to PC cable

Inspect the package and contents for visible damage. If any components are damaged or missing, do not use the unit; contact the supplier immediately. If you need to return the unit, you must ship it in the original box.

Other required equipment

You might also need the following:

  • A PC to program the PBe.

PBe ProBridge · 4310-0040 Ethernet cable · Power Supply

Page 9 of the GE PBe user manual — Power specifications
Pagina 9 · klik om te vergroten
Pagina 9

Installation environment

Power. Ensure that the installation site’s AC power is stable

and within the rated voltage of the external power supply. If the site’s AC power is likely to have spikes or DIPs, use power line conditioning or an uninterruptible power supply.

Temperature. Observe the unit’s ambient temperature

specifications when choosing a location for the unit. Extremes of heat or cold beyond the specified operating temperature limits may cause the unit to fail. Do not install this unit on top of other hot equipment.

Moisture. Do not expose the unit to rain or moisture.

Moisture can damage internal components. Do not install this unit near sources of water.

RS-232 limitations. Cable length between the POS device

and the PBe is limited to 50 ft. (15.24 m) Cable length between the PBe unit and the DVR is also limited to 50 ft. (15.24 m). If the supplied cables are replaced by custom made cables to address distances between components, ensure the cable is manufactured to ANSI standards for RS-232 communication.

Power specifications

The PBe is furnished with a power supply (110 or 240 VAC). Do not use any other power supply with this product. The manufacturer accepts no responsibility for damage caused by the use of any other power supply.

Make sure installation is complete and all connections are made before applying power to the unit.

Page 10 of the GE PBe user manual — Power supply output
Pagina 10 · klik om te vergroten
Pagina 10

4310-0007 120 VAC power supply

Power supply input

  • Voltage: 120 VAC
  • Tolerance: ± 10%
  • Frequency: 60 Hz

Power supply output

  • Voltage: 12 VDC
  • Current: 110 mA
  • Power: 1.3 watts
  • Connector: 2.1 mm female barrel. Center positive.

4310-0008 220VAC power supply

Power supply input

  • Voltage: 220 VAC
  • Tolerance: ± 10%
  • Frequency: 50 Hz

Power supply output

  • Voltage: 12 VDC
  • Current: 110 mA
  • Power: 1.3 watts
  • Connector: 2.1 mm female barrel. Center positive.
Page 11 of the GE PBe user manual — PBe components
Pagina 11 · klik om te vergroten
Pagina 11

Installation

Before installation, please familiarize yourself with the PBe and its typical system layout.

PBe components

Figure 2. PBe landmarks

GE PBe — PBe components diagram (page 11)
Afb. 3 · PBe components

Port 2/RS-232 Connects to the PC

Port 0/RS-485 Connects multiple PBes together

Power connection · Ethernet Port · Port 1/RS-232

Page 12 of the GE PBe user manual — Typical system layout
Pagina 12 · klik om te vergroten
Pagina 12

Typical system layout

The following figure shows a typical multiple ATM layout.

Figure 3. Multiple ATM system layout

GE PBe — Typical system layout diagram (page 12)
Afb. 4 · Typical system layout

4310-0034B RJ45 to RJ45 cable

Show 5 more labels / short text on this page
RS232 port · PBe · 4310-0040 Ethernet cable · Ethernet Hub · Existing ATMs
Page 13 of the GE PBe user manual — Ethernet device type
Pagina 13 · klik om te vergroten
Pagina 13

Installation overview

The basic steps required to install the PBe are:

1. Physically connect the PBe interface to the network switch or hub and the DVR using the supplied cables.
2. Program monitor mode to on by setting SW1 switches 1 to 4. See SW1 switches 1 to 4 on page 20 for the switch settings.
3. Program the camera number to be associated with the ATM’s transaction data to the PBe. See SW1 switches 5 to 8 on page 21.
4. Program the DVR to record in the way desired for your specific site.

Required information

The following information is required for a successful PBe installation. This information is used to configure the PBe. You will need to contact the customer’s ATM network administrator for answers to these questions.

Ethernet device type

  • Generic interface
  • Native ATM messages (FC)
  • Verifone POS
  • Ethernet data analyzer
Page 14 of the GE PBe user manual — Installation steps
Pagina 14 · klik om te vergroten
Pagina 14

Required DIP switch information

Important switch assignments

Table 1. Important switch assignments

SW1 1-4 Special functions

SW1 5-8 Camera assignment

SW3 1-8 Device type

Default switch settings

Table 2. Default switch settings

SW1 SW2 SW3 SW4

1 Up 1 Up 1 Up 1 Up

2 Up 2 Up 2 Up 2 Up

3 Up 3 Up 3 Up 3 Up

4 Up 4 Up 4 Up 4 Up

5 Up 5 Up 5 Up 5 Up

6 Up 6 Up 6 Up 6 Up

7 Up 7 Up 7 Up 7 Down

8 Up 8 Up 8 Up 8 Up

Installation steps

1. Select the camera number (1-16) on the DVR on which to associate the ATM transaction text. This is done by
Page 15 of the GE PBe user manual — Required DIP switch information
Pagina 15 · klik om te vergroten
Pagina 15

setting switches 5-8 on SW1. See SW1 switches 5 to 8 on page 21.

2. Connect the PBe to the network switch or hub using the supplied 4310-0040 Ethernet cable.
3. Connect the PBe to the DVR using the supplied 43100034 cable. Plug one end into port 1 of the PBe and the other end into the RS-232/2 port of the DVR.
4. Program the DVR for the desired recording functions based upon the presence of transaction text. In addition, make sure the RS-232/2 port is set for a 57600 baud rate. See the DVR manual for more information.
5. Apply power to the PBe using the supplied power supply.
Page 16 of the GE PBe user manual — HyperTerminal configuration
Pagina 16 · klik om te vergroten
Pagina 16

Programming

After you install the PBe, you need to program the ProBridge for operation. This is accomplished by using HyperTerminal or manually setting the DIP switches.

HyperTerminal configuration

You will need the following equipment to program the PBe using HyperTerminal:

  • A PC or laptop computer with a COM port and Windows 98/NT/200/XP installed and operational.
  • The supplied 4310-0061A PB3 to PC (DB9F to DB9F) cable.

To program the PBe with HyperTerminal, do the following:

1. Remove power and disconnect the PBe from the DVR.
2. Plug the 4310-0061A cable into Port 2 of the PBe and a free COM port on your PC, typically COM1.
3. Launch HyperTerminal, found in Start\Programs\Accessories\Communications\ HyperTerminal .
Page 17 of the GE PBe user manual — Figure 4. Laptop connected to PBe
Pagina 17 · klik om te vergroten
Pagina 17

Figure 4. Laptop connected to PBe

GE PBe — Figure 4. Laptop connected to PBe diagram (page 17)
Afb. 5 · Figure 4. Laptop connected to PBe
4. The Connection Description dialog box will display. Type in a name for this session (PBe) and click OK .
5. The Connect To dialog box display. Select the COM port you are connected to in the Connect Using drop-down list.
6. The COMx Properties dialog box will display. Select the following settings to complete the HyperTerminal setup:
  • Bits per second = 57600
  • Data bits = 8
  • Parity = none
  • Stop bits = 1
  • Flow control = none
7. Click OK .

To program the PBe do the following:

1. Power up the PBe by plugging in the power supply. The window shown in Figure 5 will appear confirming that you are in HyperTerminal programming mode.
Page 18 of the GE PBe user manual — Figure 5. HyperTerminal programming mode
Pagina 18 · klik om te vergroten
Pagina 18

Figure 5. HyperTerminal programming mode

GE PBe — Figure 5. HyperTerminal programming mode diagram (page 18)
Afb. 6 · Figure 5. HyperTerminal programming mode
2. Press the Enter key twice to bring up the Main Menu .

Figure 6. Main menu

GE PBe — Figure 5. HyperTerminal programming mode diagram (page 18)
Afb. 7 · Figure 5. HyperTerminal programming mode
Page 19 of the GE PBe user manual — PBe Set-up menu
Pagina 19 · klik om te vergroten
Pagina 19

Main Menu

There are five menu selections on the Main Menu:

  • Exit - Exits the maim menu and saves any changes.
  • PBe Set-up - provides IP address setup and Ethernet device selection.
  • Terminal IP/Camera Set-up - Enables or disables the IP camera and provides addressing options.
  • Monitor Mode - Toggles Ethernet monitoring On or Off.
  • Toggle Analyzer Mode - Used for Technical support only.

PBe Set-up menu

Selecting option #2 from the main menu launches the PBe Set-up menu.

Figure 7. The PBe Set-up menu

GE PBe — PBe Set-up menu diagram (page 19)
Afb. 8 · PBe Set-up menu

We recommend that you do not change the IP addresses from the defaults shown in Figure 7. The Ethernet Device option is the only option in this menu that you should change. To change the Ethernet device press 5 and then the enter key. The next device on

Page 20 of the GE PBe user manual — Terminal IP/Camera Set-up menu
Pagina 20 · klik om te vergroten
Pagina 20

the list will be selected. The PBe supports the following Ethernet devices:

  • Generic interface
  • Native ATM messages (FC)
  • Verifone POS
  • Ethernet data analyzer

Terminal IP/Camera Set-up menu

Selecting option #3 from the main menu launches the Terminal IP/Camera Set-up menu.

Figure 8. The terminal IP/camera set-up menu

GE PBe — Terminal IP/Camera Set-up menu diagram (page 20)
Afb. 9 · Terminal IP/Camera Set-up menu

Option #2 lets you associate cameras to terminals by the camera number and the terminals IP address. To associate a camera to a specific terminal do the following:

1. Press #2 and the enter key to display the camera/terminal list.
2. Enter the camera number that you want and the enter key.
3. Type in the IP address of the terminal to associate to the camera and press the enter key.
Page 21 of the GE PBe user manual — The Monitor Mode menu
Pagina 21 · klik om te vergroten
Pagina 21
4. The camera/terminal will redisplay with the new information.
5. Pressing the enter key will terminate the camera/terminal IP set-up and return you to the previous menu.

Figure 9. The camera/terminal IP table

GE PBe — Figure 9. The camera/terminal IP table diagram (page 21)
Afb. 10 · Figure 9. The camera/terminal IP table

Option #3 lets you enable/disable the Use IP for Camera command. When set to Enabled the PBe will search the incoming UDP and TCP packets for a match of IP addresses. Depending on the Device setting the PBe will parse the data received in that packet and send it to the associated camera number.

The Monitor Mode menu

The fourth selection on the Main Menu is the Monitor Mode on/ off toggle. This selection will toggle between off and on when 4

Page 22 of the GE PBe user manual — Manual DIP switch configuration
Pagina 22 · klik om te vergroten
Pagina 22

ins entered followed by the enter key. Changing the selection to on allows the PBe to monitor the incoming Ethernet packets.

In some cases whenever SW3 is used to select the Ethernet Device, monitor mode will automatically be turned on.

Analyzer Mode menu

This menu is used for troubleshooting only. Do not use unless requested by a qualified technician.

Exiting HyperTerminal

To exit HyperTerminal do the following:

1. Enter the number 1 and the enter key until the message “Exiting menus Ready!” is displayed.
2. Close the HyperTerminal screen. You do not need to save the session for your changes to take effect.
1. Remove the RS-232 cable and reconnect the PBe to the DVR.

Manual DIP switch configuration

The Ethernet Device and Camera Selection can also be selected manually by changing the DIP switch setting see DIP switch settings on page 20. Follow the steps below to change the DIP switches:

1. Disconnect power from the PBe
2. Disconnect the PBe from the DVR.
Page 23 of the GE PBe user manual — Manual DIP switch configuration
Pagina 23 · klik om te vergroten
Pagina 23
3. Set the DIP switches per the tables in DIP switch settings on page 20 to match the changes desired.
4. Reconnect the PBe to the DVR.
5. Reapply power to the PBe.
Page 24 of the GE PBe user manual — SW1
Pagina 24 · klik om te vergroten
Pagina 24

DIP switch settings

This chapter deals in detail with the DIP switch settings. The PBe must be re initialized before any changes to the switch settings will be recognized.

SW1 switches 1 to 4

Switches 1 to 4 on SW1 are for turning monitor mode on or off.

Table 3. SW1 switches 1 to 4 - monitor mode

SW1

Function 1 2 3 4

Monitor OFF U

Monitor ON D U U U

Page 25 of the GE PBe user manual — 1 U U U U
Pagina 25 · klik om te vergroten
Pagina 25

SW1 switches 5 to 8

Switches 5 to 8 on SW1 are for associating a specific camera on the DVR to the PBe.

Table 4. SW1 switches 5 to 8 - Camera number selection

SW1

Camera number 5 6 7 8

1 U

2 U U U D

3 U U D U

4 U U D D

5 U D U U

6 U D U D

7 U D D U

8 U D D D

9 D U U U

10 D U U D

11 D U D U

12 D U D D

13 D D U U

14 D D U D

15 D D D U

16 D D D D

Page 26 of the GE PBe user manual — RS-232 D U
Pagina 26 · klik om te vergroten
Pagina 26

SW3 switches 1 to 8

The switch positions on SW3 are for selecting the Ethernet device type.

Table 5. SW3 switches 1 to 8 - Device type

SW3

Switch function 1 2 3 4 5 6 7 8

Ethernet Analyzer U

Generic U D

Native ATM U D U

Verifone POS U D D

These switches are reserved for technical support. Do not use.

SW4 switches 7 and 8

Switches 7 and 8 on switch 4 control the communication protocol between the PBe at port 1 and the DVR or PC. Normally this is set at RS-232.

Table 6. SW4 switches 7 and 8 - communication protocol

SW4

Communication protocol 7 8

RS-232 D U

RS-485 U D

Page 27 of the GE PBe user manual — Accessing the Webserver
Pagina 27 · klik om te vergroten
Pagina 27

Accessing the Webserver

The PBe has a built-in webpage for simple configuration changes and remote upgrade. To access the webpage do the following:

1. Obtain the IP addresses for the PBe. The default address are:
  • IP Address: 3.112.55.79
  • Subnet mask: 255.255.254.0
  • Gateway address: 3.112.54.1
2. Connect an Ethernet cable from the Ethernet port on the PBe to a PC or hub.
3. Launch a WebBroswer program like Microsoft Explorer.
4. Enter the IP address of the PBe in the address bar of the browser.
5. The Enter Password dialog box will appear. The default log in and password for the PBe are:
  • admin
  • admin
6. Click the OK button and the Webpage will display.
Page 28 of the GE PBe user manual — Figure 10. The PBe home page
Pagina 28 · klik om te vergroten
Pagina 28

Figure 10. The PBe home page

GE PBe — Figure 10. The PBe home page diagram (page 28)
Afb. 11 · Figure 10. The PBe home page

Click on any of the hyperlinked text to navigate to that feature’s page.

Page 29 of the GE PBe user manual — Troubleshooting
Pagina 29 · klik om te vergroten
Pagina 29

Troubleshooting

Use the table below to solve some of the most common problems

Table 7. Troubleshooting table

Problem Probable cause Solution

No red LEd Fuse is bad

No text on DVR text box

DVR baud rate incorrect

Change DVR baud rate to 57600

Cable not connected on PBe port #1

Not capturing data from switch

SPAN port not configured to echo data

Consult your IS group leader for this network

Show 4 more labels / short text on this page
Replace fuse · No Power · Check Power Supply · Check cable connections
Page 30 of the GE PBe user manual — Voltage range: 110 to 240 VAC ± 10%
Pagina 30 · klik om te vergroten
Pagina 30

Technical specifications

PBe

General

HousingMetal enclosure
Dimensions4 x 7 x 1.5 in. (100 x 175 x 38 mm)
Weight5.2 oz. (161 g)
ColorBlack

Environmental

Operating temperature: 0 to 40º C.

Relative humidity10 to 80%. Storage: 10 to 95%

Electrical

AC powerIncluded external power supply

Voltage range: 110 to 240 VAC ± 10%

Current200 mA
DC powerDC jack, positive center
Power supply voltage12 VDC
Current110 mA

Power consumption: 1.5 watts max.

Page 31 of the GE PBe user manual — PBe to DVR
Pagina 31 · klik om te vergroten
Pagina 31

Cable Specifications

PBe to DVR

Part number4310-0034B
Communication typeRS-232
Connector typeRJ45
Length5 ft. (1.52 m)

Figure 11. 4310-0034B cable

GE PBe — PBe to DVR diagram (page 31)
Afb. 12 · PBe to DVR

Pin 1 · Pin 1

Page 32 of the GE PBe user manual — PBe to PC
Pagina 32 · klik om te vergroten
Pagina 32

PBe to PC

Part number4310-00061
Communication typeRS-232/Null Modem
Connector typeDB9-F, DB9-F
Length6 ft. (1.82 m)

Figure 12. 4310-0061 cable

GE PBe — PBe to PC diagram (page 32)
Afb. 13 · PBe to PC
Page 33 of the GE PBe user manual — PBe Ethernet cable
Pagina 33 · klik om te vergroten
Pagina 33

PBe Ethernet cable

Part number4310-0040
Communication typeEthernet
Connector typeRJ45, RJ45
length6 ft. (1.83 m)

Figure 13. 4310-0040 PBe Ethernet

GE PBe — PBe Ethernet cable diagram (page 33)
Afb. 14 · PBe Ethernet cable
Page 34 of the GE PBe user manual — Online publication library
Pagina 34 · klik om te vergroten
Pagina 34

Contacting technical support

For assistance installing, operating, maintaining, and troubleshooting this product, refer to this document and any other documentation provided. If you still have questions, you may contact technical support during normal business hours (Monday through Friday, excluding holidays, between 6 a.m. and 5 p.m. Pacific Time).

Table 8. Sales and support contact information

Phone Toll-free: 888.GESECURity (888.437.3287 in the US, including Alaska and Hawaii; Puerto Rico; Canada).

Outside the toll-free area: 503.885.5700.

E-mail info@gesecurity.com generaltech@ge.com

Fax 800.483.2495 541.752.9096 (24 hours/day)

Online publication library

Another great resource for assistance with your GE product is our online publication library, available to all of our customers. To access the library, go to our website at the following location:

http://www.gesecurity.com

In the Tools area at the top, click the Publication Library link. After you register and log on, you may search through our online library for the documentation you need.1

1. Many GE documents are provided as PDFs. To read these documents, you will need Adobe Acrobat Reader, which can be downloaded free from Adobe’s website at www.adobe.com.

Sales Technical support

Bronnen

Referenties en links

Pagina's waarnaar wordt verwezen in deze handleiding — fabrikant, ondersteuning en downloads.

Probleemoplossing

Probleemoplossing

Veelvoorkomende problemen, mogelijke oorzaken en oplossingen.

ProbleemMogelijke oorzaakOplossing
No red LEdFuse is bad No PowerReplace fuse Check Power Supply p.29
No text on DVR text boxDVR baud rate incorrect Cable not connected on PBe port #1Change DVR baud rate to 57600 Check cable connections p.29
Not capturing data from switchSPAN port not configured to echo dataConsult your IS group leader for this network p.29

Vraag stellen over de GE PBe

Eigenaren en ons team reageren doorgaans binnen een dag — en uw vraag helpt ook de volgende persoon.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Nog geen vragen over de GE PBe

Stel als eerste een vraag — andere eigenaren of ons team geven antwoord.

Origineel document

GE PBe handleiding-pdf

34 pagina's·2.2 MB·Switch·PDF
Klik op een bovenstaande pagina om deze hier te openen
Pagina 1 / …
100%
Pagina's laden…