Gebruiksaanwijzing /service van het product PMX-IC B van de fabrikant Genie
Ga naar pagina of 32
Au t o mat i c Cha i n D riv e/ Be lt D rive Ga ra ge Door O p er a t or S yst e m Owner ’ s Manual SA VE FOR FUTURE REFERENCE Customer Ser vice CALL: 1-800-354-3643 VISIT : WWW .
Things to consider if you are planning to “ do-it-yourself. ” Whether you are replacing an existing garage door operator or installing an operator in your garage for the first time, there are some pre-installation issues which need to be addressed.
3 TYPICAL SECTIONAL DOOR INST ALLA TION 5 TYPICAL SUPPORT BRACKET EXTENSION SPRING OR T ORSION SPRING SAFE-T -BEAM ® BRACES ADDED HEADER BRACKET MOUNTING BOARD 36 ” POWER CORD TO 120V GROUNDED OUTL.
4 W ARNING : Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual.
NOTE: Accessories vary by model . F ASTENERS - Shown full size. See Parts List for description. 10 5 10 4 103 101 10 6 12 6 12 4 12 5 Lag Screw , 1/4 ” x 2 ” Cotter Pin Clevis Pin Bolt, 3/8 ” -16 x 7/8 ” Phillips Hex Head Screw , No.
Stealth Power Head 2 3 4 5 6 7 8 9 10 1 12 13 14 15 16 17 18 19 20 11 22 23 24 25 26 27 28 29 30 21 32 33 34 35 36 37 38 39 31 40 12 12 12 12 11 19 3 12 26 26 Item Part Name 1 Lens 2F ront Cover 3S id.
7 PA R TS IDENTIFICA TION FOR HELP-1.800.354.3643 OR GENIECOMP ANY .COM Item Part Name 61 Main Drive Worm 62 Screw , #8 x 3-1/8 ” Slot HH, Sf T ap 63 Limit Switch Plate 64 Screw , #6 x 3/8 ” Phill.
Channel Item Part Name 66 Belt & Bullet Assembly - 7 ’ 6 ” Door (Belt Models Only) Belt & Bullet Assembly - 8 ’ Door (Belt Models Only) Belt & Bullet Assembly - 10 ’ Door (Belt Mod.
9 Rail PA R TS IDENTIFICA TION FOR HELP-1.800.354.3643 OR GENIECOMP ANY .COM Item Part Name 102 Boom Support Kit (not shown) 103 Safety & Maintenance Guide 104 Emergency Release T ag (Tri-L) 105 Entrapment W ARNING Label 106 Wire 11 0 R a il (L=1 12.
Fig. 1-3 No. 10-24 x 1/2 ” Hex Head Screws 5/16 ” x 1/2 ” Hex Head Screws “ D ” -Shaft and Hole 3. Place power head and channel on clean, flat surface. 4. Slide drive end of channel down over “ D ” -shaft on top of power head (Fig. 1-2).
Fig. 1-4 Adjusting Bolt WHA T TYPE OF DOOR DO YOU HA VE? Look at the drawings below . They tell you where to find the installation instructions you need T rack Guided Doors SEE SECTION 2A T rackless Doors SEE SECTION 2 B.
W ARNING • Do Not try to remove, repair or adjust springs or anything to which door spring parts are fastened, such as, wood blocks, steel brackets, cables or other like items. Repairs and adjustments must be made by a trained service person using proper tools and instructions.
CAUTION CAUTION Fig. 2-5 Mounting bracket must be fastened to garage framing. Do Not fasten to drywall, particle board, plaster or other such materials. Power Head Channel/Rail Assembly 6. Mount power head (See Section 2 MOUNTING METHODS). • Be sure channel/rail assembly and power head are on door center line (Line “ V ” ).
8. Install door bracket (Fig. 2-6). • Contact door manufacturer . NOTE: Self-drilling screws are intended for use with light-weight door only , while lag screws are meant for wood doors only . Because door designs vary , modifications may be required and additional materials needed.
CAUTION W ARNING Header bracket must be fastened to garage framing. Do Not fasten to drywall, particle board, plaster or other such materials. 1. Establish center line of door and header (Fig. 2-9). • Close door . • Measure door width. Mark center .
CAUTION 6. Install door bracket (Fig. 2-12). • Contact door manufacturer for proper installation. NOTE: Self-drilling screws are intended for use with light-weight door only , while lag screws are meant for wood doors only . Because door designs vary , modifications may be required and additional materials needed.
CAUTION Mounting bracket must be fastened to garage framing. Do Not fasten to drywall, particle board, plaster or other such materials. 9. Mount power head (See Section 2 AL TERNA TE MOUNTING METHODS). • Be sure rail assembly and power head are on door center line (line “ V ” ).
NOTE: Mounting brackets can be attached to the floor using concrete anchors (not provided). 2. Mounting STB source and sensor . • If garage has only one garage door . – Determine which side of garage receives most direct sunlight (Fig. 3-4) . – Red LED should always be on sunny side whenever possible (Fig.
CAUTION FIG. 3-8 (ProMax) Attachments at power head . • Make wire attachments at STB ’ s. – Splitting and stripping wire ends to be connected as shown (Fig. 3-6) . – Loosen terminal screws. – Insert wire under flat plate and tighten screw . It does not matter which wire, white or striped, goes on which terminal (Fig.
CAUTION W ARNING W all console W all button OR Fig. 4-2 #6 x 1 ” pan head screws Fig. 4-3 MORE T MENT OPEN PUSH LIMITS TO SET G4 Y3 B2 W1 1. Run wire from power head to wall control. • Place the wall control: – In sight of door . – At least 5 feet from floor , so small children can not reach it.
1. Disconnect the power cord from the branch circuit mains. 2. Remove bottom cover from power head. • Remove four (4) hex head screws from front and rear covers. • Slide bottom cover off. 3. Remove existing power cord from power head. • Disconnect three power cord wires.
W ARNING Fig. 6-1 MORE MORE LIMIT ADJUSTMENT CLOSE OPEN PUSH LIMITS TO SET 4 3 2 1 CLASS 2 NEC OPEN CLOSE TO SET LIMITS PUSH OR NEC CLASS 2 1 2 3 4 5 6 MORE FORCE PUSH BUTTON SAFETY BEAM LIMIT SET OPE.
NEC CLASS 2 1 2 3 4 5 6 MORE FORCE PUSH BUTTON SAFETY BEAM LIMIT SET OPEN FORCE CLOSE FORCE RADIO SIGNAL LEARN CODE COM DO NOT PUSH LIMIT SET UNLESS DOOR IS ATTACHED NOTE: USE ONLY WITH SERIES II CONTROLS CLOSE MORE OPEN MORE CLOSE OPEN LIMIT ADJUSTMENT U.
W ARNING During the following steps, the motor protector may open. W ait about 20 minutes for protector to reset. 1. Adjusting the “ OPEN ” limit switch (Fig. 8-1). • Run door to open position by pushing wall control. • Locate curved “ OPEN ” limit adjustment slot on back of power head.
1. T urn remote control upside down (Fig. 10-1) 2. Battery replacement (your remote control is battery powered). • Gently push straight IN on tab as shown (Fig. 10-1). – use ball point pen, coin or small screwdriver . – battery cover snaps open.
1. Install light bulb(s) into socket(s). Do Not use short neck bulb(s). • Use bulb(s) rated for: – rough service. – vibration. – appliances. • 1 00 watt maximum. 2. Bend two (2) slotted tabs up. This will activate the ” living hinge ” of the lens (Fig.
MONTHL Y MAINTENANCE DOOR SPRINGS and DOOR HARDW ARE • Do not operate garage door automatically or manually if springs are broken. CONT ACT A PROFESSIONAL FOR SERVICE. • Oil door rollers, bearings, and hinges monthly . Use silicone lubricant or light oil.
CAUTION Door starts for no reason. Check staples on wire from power head to wall control. If they cut into insulation, they can short wires. If wire is cut, replace it. W as a remote control lost or stolen? Erase all remote control codes from receiver memory and reprogram.
CAUTION ( Stealth Motor ) Openin g cover could cause electrical shock. WIRING DIAGRAM FOR HELP-1.800.354.3643 OR GENIECOMP ANY .COM 29 ( ProMax Motor ).
30 No C.O .D . shipments. Please include check or money order , made pay able to The Genie Company . Do not send cash .A llow 3-4 weeks f or delivery . 1-800-354-3643. Please have part number and credit card ready . Mail Order Form to: Genie Company , Alliance, Ohio 44601 .
INST ALLA TION NOTES FOR HELP-1.800.354.3643 OR GENIECOMP ANY .COM CONT ACT NUMBERS NAME COMP ANY NUMBER NAME COMP ANY NUMBER NAME COMP ANY NUMBER NAME COMP ANY NUMBER NAME COMP ANY NUMBER NAME COMP A.
SA VE THESE INSTRUCTIONS Manufactured under one or more of the following U.S. patents: 3,898,582 / 4,041,259 / 4,048,630 / 4,064,487 / 4,103,238 / 5,222,403 Other Patents applied for 22790 Lake Park Blvd. • Alliance, Ohio USA • 44601 Customer Service 1.
Een belangrijk punt na aankoop van elk apparaat Genie PMX-IC B (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Genie PMX-IC B heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Genie PMX-IC B vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Genie PMX-IC B leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Genie PMX-IC B krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Genie PMX-IC B bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Genie PMX-IC B kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Genie PMX-IC B . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
