Gebruiksaanwijzing /service van het product POWERLIFT 900 van de fabrikant Genie
Ga naar pagina of 24
For Answers and Assistance: 1.800.354.3643 or visit www .geniecompany .com SAVE THIS MANUAL FOR FUTURE REFERENCE INST ALLER: LEAVE THIS MANUAL WITH HOMEOWNER GARAGE DOOR OPENER MODELS P owerMax ® 120.
Safety Information Safety Notifications .......................................... 3 Important Safety Instructions ............................ 3 Infrared Protection Function ............................. 3 Features Safety ...........................
SafetyInformation 1 OVERVIEW OF PO TENTIAL HAZARDS READ THIS SAFETY INFORMA TION CONVENTIONS USED IN THESE INSTRUCTIONS Garage doors are large, heavy objects tha t move with the help of springs under high tension and electric motors.
Features 2 SAFETY FEA TURES Safe-T -Beam ® (STB) Non-Contact Reversing System Puts an invisible beam across the door opening. The door stops and reverses to the full open position if anything passes through the beam. LED indicator lights on the powerhead and on the STBs provide a self-diagnostic code if an operational problem exists.
Required Programming 3 NOTE: Before you begin programming, check to make sure there are no objects in the garage door opening. INTRODUCTION Now that your Genie gara ge door opener is installed, you will want to program the opener so that the door opens and closes properly and all remote devices operate correctly .
TRA VEL LIMITS NOTE: If shuttle/bullet has NOT been enga ged to carriage, do so now . See page 17. NOTE: Before setting limits confirm wall console red indicator light (or backlight) is ON. If not illuminated, check for correct wiring or the Sure-Lock switch may be activated.
Required Programming 3 The DOWN (closed) limit is programmed. Opening Garage Door (Up Limits) NOTE: Beginning with garage door c losed is recommended but not necessary . The UP (open) limit is programmed. BOTH DOOR LIMITS ARE NOW PROGRAMMED . PROGRAM SET PROGRAM – + 5 Press and release the Program Set button (both LEDs flash blue and go off).
R quired Pr ramming Required Programming 3 MODEL AC SR3 THE GENIE COMPANY FCC ID: B8Q AC SR3 Residential Door Operator IC: 2 33A-CS 1D 120V. 60HZ. 5A S/N:10XXXX XXXXXXX STB BWC IWC NOT USED NOT USED N.
Required Programming 3 Force and Speed Control These controls are factory programmed and automa tically set themselves when you use the Wall Console to open and c lose the garage door for the rst time. The door MUST complete a full cyc le from open to close and c lose to open before it is fully set.
Required Programming 3 REMOTES / New Intellicode 2 Openers NOTE: The following instructions are for the remote control transmitters (“Remotes”) provided with this opener . This Remote is preset for use with the Intellicode 2 Access Security System.
The Remote button is now programmed. Repeat as necessar y for additional Remotes. T o program the same Remote for other garage door openers, repeat the steps above using one of the other two Remote buttons. Each Remote can be programmed for three door openers.
Optional Programming 4 Setting Up a PIN 1. Press in order 3–5–7. 2. Press the Program key . 3. Enter your new PIN (3-8 characters). 4. Press Program key . Y our keypad is ready for programming. Programming Locate Y our Opener’ s Programming Buttons and LED Synchronizing Keypad to Opener 1.
Optional Programming 4 CLEARING MEMOR Y FOR REMOTES If the memory has been cleared, the Remote will not activate the door opener . NOTE: The garage door opener will operate normally using the Wall Console. NOTE: When the remote is pressed the round LED will flash blue but will not activate the door opener .
INTELLICODE 1 REMOTES Remotes provided with this unit can operate other (Intellicode® 1) models of Genie® garage door openers . The default Intellicode ® 2 setting must be changed to Intellicode® 1. (Follow these same steps to change Intellicode® 1 back to Intellicode® 2.
One-Piece Doors 5 A TT ACHING DOOR BRA CKET TO DOOR NOTE: Center bracket on door as high as possible, preferably top edge . A TT ACHING DOOR ARM T O DOOR BRACKET 1 Using bracket, mark holes on door or frame and drill 5/32" hole completely through door frame.
Maintenance and Adjustments 6 If you have any questions, please do not hesitate to contact customer service a t: 1-800-35-GENIE or visit www .geniecompany .
W ARNING •Useextremecautionwhenworkingfromaladderorstepstool. • Whenreplacinglightcover , makesurewiresarenotpinchedor near moving parts.
Maintenance and Adjustments 6 CAUTION Door closing force is F ACTOR Y set and requires no adjustment for normal operation. • NEVER adjust the force settings to compensate for damage, including an unbalanced door , binding door track, or broken spring.
Maintenance and Adjustments 6 ADJUSTMENT GUIDES (continued) Speed Settings (DC motors only) Speed settings are pre-programmed at the factor y for the maximum speed.
Opener circuit wiring diagram. This wiring diagram is for reference only . WiringDiagram 7 1 2 3 4 5 6 1 2 3 7 6 POWERCORD CONNECTOR WHITE BLACK GREEN WHITE WHITE BLACK RED BLACK STRIPEDWHITE.
Troubleshooting 8 OPERA TION Need help or have questions? DO NOT RETURN to the store. Call us: 800-354-3643 PROBLEM WHA T TO DO Opener does NO T run from wall console. •Checkpowersource. – Plug a lamp into outlet used for powerhead. If lamp works, power source is OK.
Troubleshooting 8 Powerhead LED Possible Problem Solution Round LED Long LED OFF OFF Normal operation. None required. No response from unit. Check power supply. Contact a trained door system technician. ON/RED/ STEADY ON/RED/ STEADY Limits NOT set properly.
PowerMax ® 1200/1500, SC 1200/1500, TriloG ™ 1200/1500, PowerLift ® 900, GPower ™ 900, SilentMax ® 1000/1200, CB 1000/1200, IntelliG ® 1000/1200 LIMITED WARRANTY GMI Holdings, Inc d/b/a The Ge.
Looking for Leading-Edge T echnolog y or the P erfect Update/Replacement? Genie ® Has the Answer! L ea ding- Edge Techn ol og y Closed Conrm™ W ireless Remote (Works with Rev olution Series 1500, 1200 and 1000 Models) • Sleekandcompactdesign • Beepsandashesgreenwhengarage doorcloses.
Een belangrijk punt na aankoop van elk apparaat Genie POWERLIFT 900 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Genie POWERLIFT 900 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Genie POWERLIFT 900 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Genie POWERLIFT 900 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Genie POWERLIFT 900 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Genie POWERLIFT 900 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Genie POWERLIFT 900 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Genie POWERLIFT 900 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
