Gebruiksaanwijzing /service van het product AM1M-S2H van de fabrikant Gigabyte
Ga naar pagina of 32
GA-AM1M-S2H User's Manual Rev . 1001 12ME-AM1MS2H-1001R.
Motherboard GA-AM1M-S2H Jan. 27, 2014 Jan. 27, 2014 Motherboard GA-AM1M-S2H Copyright © 2014 GIGA-BYTE TECHNOLOGY CO., L TD. All rights reserved. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE.
- 3 - T able of Contents GA-AM1M-S2H Motherboard Layout .............................................................................. 4 GA-AM1M-S2H Motherboard Block Diagram .................................................................. 5 Chapter 1 Hardware Installation .
- 4 - GA-AM1M-S2H Motherboard Layout The box contents above are for reference only and the actual items shall depend on the product package you obtain.
- 5 - For detailed product information/limitation(s), refer to "1-2 Product Specications." GA-AM1M-S2H Motherboard Block Diagram APU CLK+/- (100 MHz) Memory PCI Express Bus LPC Bus BIOS PCIe CLK (100 MHz) PS/2 KB/Mouse 8 USB 2.0/1.1 2 USB 3.
- 6 - Chapter 1 Hardware Installation 1-1 Installation Precautions The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD).
- 7 - 1-2 ProductSpecications APU FS1b Socket: - AMD Athlon ™ series processors - AMD Sempron ™ series processors (Go to GIGABYTE's website for the latest CPU support list.
- 8 - Back Panel Connectors 1 x PS/2 keyboard port 1 x PS/2 mouse port 1 x D-Sub port 1 x HDMI port 2 x USB 3.0/2.0 ports 2 x USB 2.
- 9 - 1-3 Installing the APU Read the following guidelines before you begin to install the APU: • Make sure that the motherboard supports the APU. (Go to GIGABYTE's website for the latest APU support list.) • Always turn off the computer and unplug the power cord from the power outlet before installing the APU to prevent hardware damage.
- 10 - 1-6 Back Panel Connectors PS/2 Keyboard and PS/2 Mouse Port Use the upper port (green) to connect a PS/2 mouse and the lower port (purple) to connect a PS/2 keyboard. D-Sub Port The D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of 1920x1200 (the actual resolutions supported depend on the monitor being used).
- 1 1 - • When removing the cable connected to a back panel connector , rst remove the cable from your device and then remove it from the motherboard. • When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector .
- 12 - 1/2) A TX_12V/A TX (2x2 12V Power Connector and 2x12 Main Power Connector) With the use of the power connector , the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector , rst make sure the power supply is turned off and all devices are properly installed.
- 13 - 5) SA T A3 0/1 (SA T A 6Gb/s Connectors) The SA T A connectors conform to SA T A 6Gb/s standard and are compatible with SA T A 3Gb/s and SA T A 1.5Gb/s standard. Each SA T A connector supports a single SA T A device. Pin No. Denition 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND DEBUG PO RT G.
- 14 - 7) SPDIF_O(S/PDIFOutHeader) This header supports digital S/PDIF Out and connects a S/PDIF digital audio cable (provided by expansion cards) for digital audio output from your motherboard to certain expansion cards like graphics cards and sound cards.
- 15 - 12) CLR_CMOS(ClearCMOSJumper) Use this jumper to clear the BIOS conguration and reset the CMOS values to factory defaults. T o clear the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds. • Always turn off your computer before clearing the CMOS values.
- 16 - 14) BA T (Battery) The battery provides power to keep the values (such as BIOS congurations, date, and time information) in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may be lost.
- 17 - 2-1 Startup Screen The following startup Logo screen will appear when the computer boots. (Sample BIOS V ersion: F1) Function Keys • When the system is not stable as usual, select the Load OptimizedDefaults item to set your system to its defaults.
- 18 - ` Advanced Frequency Settings & Processor Graphics Clock Allows you to set the onboard graphics clock. The adjustable range is from 300 MHz to 2000 MHz. & CPU NorthBridge Frequency Allows you to manually set the CPU North Bridge frequency .
- 19 - (Note) This item is present only when you install a CPU and a memory module that support this feature. ` Advanced Memory Settings & ExtremeMemoryProle(X.
- 20 - & CPU/System Fan Fail Warning Allows the system to emit warning sound if the CPU fan or system fan are not connected or fail. Check the fan condition or fan connection when this occurs. (Default: Disabled) & CPU Fan Speed Control Allows you to determine whether to enable the fan speed control function and adjust the fan speed.
- 21 - & System Date Sets the system date. The date format is week (read-only), month, date, and year . Use <Enter> to switch between the Month, Date, and Y ear elds and use the <Page Up> or <Page Down> key to set the desired value.
- 22 - & Bootup NumLock State Enables or disables Numlock feature on the numeric keypad of the keyboard after the POST . (Default: Enabled) & SecurityOption Species whether a password is required every time the system boots, or only when you e nter BIOS Setup.
- 23 - & Boot Mode Selection Allows you to select which type of operating system to boot. UEFI and Legacy Allows booting from operating systems that support legacy option ROM or UEFI option ROM. (Default) Legacy Only Allows booting from operating systems that only support legacy Option ROM.
- 24 - 2-5 Peripherals & HDAudio AzaliaDevice Enables or disables the onboard audio function. (Default: Enabled) If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to Disabled . & OnboardLANController Enables or disables the onboard LAN function.
- 25 - ` GFXConguration & Primary Video Device Species the rst initiation of the monitor display from the installed PCI Express graphics card or the onboard graphics.
- 26 - 2-6 Power Management & Resume by Alarm Determines whether to power on the system at a desired time. (Default: Disabled) If enabled, set the date and time as following: Wake up day: T urn on the system at a specic time on each day or on a specic day in a month.
- 27 - & PowerOnPassword Set the password when PowerOnByKeyboard is set to Password . Press <Enter> on this item and set a password with up to 5 characters and then press <Enter> to accept. T o turn on the system, enter the password and press <Enter>.
- 28 - & SaveProles This function allows you to save the current BIOS settings to a prole. Y ou can create up to 8 proles and save as Setup Prole 1~ Setup Prole 8. Press <Enter> to complete. Or you can select Select File in HDD/USB/FDD to save the prole to your storage device.
- 29 - Regulatory Statements Regulatory Notices This document must not be copied without our written permission, and the contents there of must not be imparted to a third party nor be used for any unauthorized purpose. Contravention will be prosecuted.
- 30 - FCCNot ic e(U.S. A .O nl y) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- 31 -.
- 32 - Contact Us GIGA-BYTETECHNOLOGYCO.,L TD. Add re ss: N o.6 , Bao C hia ng Ro ad, H si n-Ti en D ist ., New Taipe i Cit y 2 31, T a iwa n TEL: + 88 6 -2- 8912- 40 0 0, FA X: + 88 6 -2- 8912- 40 0 5 T e ch . and N on -T e ch. S upp or t (Sal es / Mar ket in g) : htt p://gg ts .
Een belangrijk punt na aankoop van elk apparaat Gigabyte AM1M-S2H (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Gigabyte AM1M-S2H heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Gigabyte AM1M-S2H vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Gigabyte AM1M-S2H leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Gigabyte AM1M-S2H krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Gigabyte AM1M-S2H bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Gigabyte AM1M-S2H kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Gigabyte AM1M-S2H . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
