Gebruiksaanwijzing /service van het product Reference II Turntable van de fabrikant Goldmund
Ga naar pagina of 21
ASSEMBLY & USER MANUAL GOLDMUND REFERENCE II.
Table of Contents 1. UNPACKING 4 2. CHOICE OF YOUR TURNTABLE LOCATION 4 3. TURNTABLE ASSEMBLY 5 4. TONE ARM ASSEMBLY 19 5. USER INSTRUCTIONS 20 6. CLEANING AND MAINTENANCE 21.
The Goldmund Reference II – Assembly manual 3 I M P O R T A N T ! The Goldmund Reference II you just purchased represents a summit in terms of design, concept and quality of reproduction. Therefore, great care should be taken before attempting to put the unit together.
The Goldmund Reference II – Assembly manual 4 1 UNPACKING Your turntable is shipped in 4 separate wood boxes labeled 1 to 4 and 1 carton box labeled 5: - Box 1: the base (feet assembly) - Box 2: the.
The Goldmund Reference II – Assembly manual 5 3 TURNTABLE ASSEMBLY STEP 2 Box 2: the Table top Unscrew and remove the top cover of the wood box n°2. Remove the protection cover, Mount the table top on the base with the control panel keyboard facing the front.
The Goldmund Reference II – Assembly manual 6 STEP 3 Box 3: Tripod Unscrew and remove the top cover of the wood box n°3. Remove the protection cover. Remove the 3 cylindrical weights sitting on top of the tripod feet. STEP 4 Box 3: Tripod Unscrew the tripod from its 3 feet.
The Goldmund Reference II – Assembly manual 7 STEP 5 Box 3: Tripod Free the tripod assembly from the box and set it on 3 temporary supports like foam rubber or books, leaving the center free.
The Goldmund Reference II – Assembly manual 8 STEP 6 Box 3: Tripod In the box n°3, you will find the 3 cylinder feet of the tripod. Please take one cylinder foot to position it at the front left position. Be carful to select the foot with the correct basis (check the bottom of the foot).
The Goldmund Reference II – Assembly manual 9 Box 4: Various Parts In the box n°4, you will find: - 1 platter - 1 motor bloc - 1 belt - 12 rubber seals - 1 large golden insert - 3 small golden insert - 1 clamp - 1 small oil bottle STEP 7 Box 4: Various Parts Take the large golden insert.
The Goldmund Reference II – Assembly manual 10 STEP 9 Box 3: the tripod In the box n°3, take the last cylinder foot. Check if its design is the same as the one shown on the left picture. Position it in the bottom of the third cylinder foot position, passing the axe through the hole.
The Goldmund Reference II – Assembly manual 11 STEP 10 Adjust the 3 springs: Turn the springs has shown. Correct position Too High Too low.
The Goldmund Reference II – Assembly manual 12 STEP 11 Take 4 rubber seals and insert them in one of the 3 holes on the table: 4 rubber seals per hole. Repeat the operation for both other holes. STEP 12 When the seals are positioned, place 1 golden insert in the hole.
The Goldmund Reference II – Assembly manual 13 STEP 13 For this step, you need to be 2 persons. One person take carefully the motor block by its basis and keep in above the 3 holes with the golden insert, as shown on the picture.
The Goldmund Reference II – Assembly manual 14 STEP 14 Take the tripod and mount it as shown on the left picture: The arm with the 4 small holes should be directing towards the rear foot of the turntable. ATTENTION: Please check the tripod is well positioned.
The Goldmund Reference II – Assembly manual 15 STEP 15 Screw, but not over-tight, the tripod to the feet with the 3 screws dismounted at the beginning of the assembly (see STEP 4).
The Goldmund Reference II – Assembly manual 16 STEP 17 Add some oil contained in the bottle in the axis shaft. IMPORTANT: After this step, make sure you clean your hands from any oil. STEP 18 Reinsert the axis with extreme care into the shaft assembly.
The Goldmund Reference II – Assembly manual 17 STEP 20 Mount the platter on the center axis. This should be done with great care and the platter must be set in position very slowly. IMPORTANT The platter shouldn’t at any time be dropped or shocked.
The Goldmund Reference II – Assembly manual 18 STEP 22 Put the 3 top cylinders on the tripod. STEP 23 Check the level of the table top first, then the platter with a bubble level. If needed, repeat step 21 with the platter positioned. STEP 24 Box 5 Please remove the power supply from its box and position it nearby the turntable.
The Goldmund Reference II – Assembly manual 19 4 TONE ARM ASSEMBLY The Goldmund Reference II can be used with most existing ton arms, both pivoting and straight-line. Up to three tone arms may be assembled on the turntable. Even if the Goldmund T8 tone arm is installed, two additional pivoting arms may be used.
The Goldmund Reference II – Assembly manual 20 5 USER INSTRUCTIONS Now your turntable is assembled, you can start using it: 1- Switch on the power supply 2- Unscrew the clamp and remove it very carefully. 3- Position the record to play 4- Re-mount the clamp carefully; tighten it holding its basis.
The Goldmund Reference II – Assembly manual 21 6 CLEANING AND MAINTENANCE There is no special maintenance to be done on your turntable. Clean with dust free soft cloth. Drive wheel and motor pulley may be cleans after months of use or if abnormal speed variation occurs.
Een belangrijk punt na aankoop van elk apparaat Goldmund Reference II Turntable (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Goldmund Reference II Turntable heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Goldmund Reference II Turntable vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Goldmund Reference II Turntable leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Goldmund Reference II Turntable krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Goldmund Reference II Turntable bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Goldmund Reference II Turntable kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Goldmund Reference II Turntable . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
