Gebruiksaanwijzing /service van het product 255963 van de fabrikant Graco
Ga naar pagina of 32
Instr uctions - P ar ts Doub le W all Hopper For use with XM ™ plural-component spray er s and immer sion heaters. For prof essional use only . 255963, Double W all Hopper 20 Gallon (75 liter ) Spra y Material Fluid Capacity 12 Gallon (45 liter) Heat ed Material Fluid Capacity See page 12 f or optional accesso ries and approv als.
Related Manua ls 2 312747L Contents Related M anuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Optional Accessorie s . . . . . . . . . . . . . . . . . . . . . . . 3 W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Accessories 312747L 3 Optional Accessories See Accessorie s on page 28 f or par ts lists. Not appro ved f or use in e xp losiv e atmosphers or hazardous location s Not all accessories and kits are app rov ed f or use in hazardous locations .
Warnings 4 312747L Wa r n i n g s The f ollowing w arnings are for t he setup , use, g rounding, maintenance , and repair of this equ ipment. The e xclama- tion point symbol alerts you to a gener al warning and the hazard symbol ref ers to procedure -specific risk.
Warnings 312747L 5 W ARNING W ARNING W ARNING W ARNING PRESSURIZED EQUIPMENT HAZARD Fluid from the gun/dispense v alv e, leaks , or ruptured components can spla sh in the ey es or on skin an d cause serious injury .
Warnings 6 312747L K eep Components A and B Separate Changing Materials • When changing m aterials, flush the equipment mul- tiple times to ensure it is th oroughly clean.
Component Identi fication 312747L 7 Component Identification Double W all Hoppers Mounted on Side of Frame Key: AF r a m e BX t r e m e ® low er (behi nd the fr ame) CN X T ™ air motor (behind the .
Overview 8 312747L Overview Double wall hopper s (D) can be mounted on the bac k or side of the frame ( A) to gra vity f eed spr a y material to the Xtreme lo wer (B). F e ed pumps (H) and agita tors (J) can be mounted on to p of the hoppers to pre ssure f eed spra y mater ial directly to the pump.
Installation 312747L 9 Installation Hopper mounting kit 256259 allows the ho ppers (D) to mount on the sid es or back of t he frame (A). 1. Mount hoppers (D) on sides of the frame ( A). See F IG . 3. a. Attach ma in brack et (101) to f rame (A) with screw s (107).
Installation 10 312747L c. Attach the cor ner brac ket (103) to frame (A) with screw s (108) and washe rs (110). d. Attach lower mo unt brack et (104) to frame (A) with screws (108) and washers (110) . e. Attach main br ack et (101 ) to frame (A) with screws (107).
Installation 312747L 11 7. Align holes on main br ack et (101) and thr ead inser ts of the hopper (D). Loosely f aste n hopper (D) to brac k et (101) with f our scre ws (107) and washers (110). 8. Conne ct s wivel fitting (202) to nipple (201 ). 9. Tighten union (208) and ensure fluid outlet assem- bly is aligned.
Installation 12 312747L Optional Accessories See Accessorie s page 28 f or a list of all accessories that can be used with doub le wall ho ppers. Immersion Heater Kit 256257 Immersion heater kit 2562 57 can only be used with a water mixture or oil in the outer jac ket ed area of the h op- per .
Installation 312747L 13 8. Set thermostat knob (TK) to desired spra y ma terial conditioning te mperature. Align tempe rature setting to set point (SP). NO TE: Set point (SP) is a “V” notc h in the metal brac ket at the top of the t hermostat dial.
Setup 14 312747L Setup 1. Remov e the large A or B label fr om the label sheet (24) and apply t o front f ace of the appropriate hop - per to help av oid filling the wrong materials and causing cross-contamination. 2. Remov e the small A o r B from the label sheet (24) and apply on lid.
Setup 312747L 15 Fill Heating Fluid Fill the hopper’ s outer jack e ted area with oil or a 50% water an d 50% eth ylene glycol mixture t o heat yo ur spra y material. The doub le wall hopper de sign pre v ents the spr ay mat erial from losing heat during do wntime and ov ernight.
Setup 16 312747L 5. Install plug (6) in opposit e por t and torque to 20-30 ft-lbs (27-41 N•m). NO TE: Occasionall y inspect the inside of the hopper for any lea kage of outer c avity heat ing fluid. Fill Spra y Material Condition materials prior to adding to hoppe rs.
Operation 312747L 17 Operation Star tup 1. Ensure that the outer jac k eted area is filled with water mixture or oil and the ac cessor ies are cor- rectly installed. 2. Follo w Setup procedure in man ual 312359. 3. See manual 312 359 f or testing material and oper a- tion inst ructions bef ore spra ying material.
Maintenance 18 312747L Maintenance Chec k Heating Fluid Level Gradual f luid e va poration can occur , theref ore , check the le v el of heating fluid monthly . 1. Remove plug (6). 2. Place flexible object in por t so that it protr udes down. Pull out to observe le ve l.
Maintenance 312747L 19 Drain Spra y Material 1. Flush and Shutdown XM spra y er . See XM opera- tion manual. 2. T urn off all fluid heaters (S) and allow heating flu id to cool for a minimum of 8 ho urs. 3. Place a clean 1 gallon (4 liter) pail directly bene ath union (208 ) and ball valve (206).
Repair 20 312747L Repair Remo ve Immer sion Heater 1. T ur n off powe r to system. See the XM Oper ation manual . 2. Drain Heating Fluid . See page 18. 3. Remov e scre ws (HS) and immersion heat er cov er (HC). 4. Disconnect white , blac k, and gr een wires from power cable (303).
Repair 312747L 21 Remo ve Hopper 1. Check Heating Fluid Level . See page 18. 2. Drain Spray Material . See page 19. 3. Disconnect s wiv el fitting (2 02). See F IG . 29. 4. If a transf e r pump (H) or agitator (J) is mounted to the hopper: a. Relieve pressure .
Troubleshooting 22 312747L T roub leshooting Prob lem Cause Solution Lid does not properly seal on hopper . Material build up . Remov e b uilt up material from gas- ket. Replace as necessar y . Damaged gask et. Material leaking betw een cov er an d hopper .
Troubleshooting 312747L 23.
Parts 24 312747L Pa r t s 255963, Double W all Hopper 1 Assemble with lips f acing down. T orque to 20-30 ft-lbs. Clean groov e with isoprop yl alcohol before applying gask et adhesiv e to plastic.
Parts 312747L 25 255963, Double W all Hopper Replacement Dange r and W arning labels, tags , and cards are av ailab le at no cost. † Supplied spacer kit is f o r installat ion of a 5:1 pump on this hopper . See manual 312769 f or inst ructions. Ref.
Parts 26 312747L 256259, Double W all Hopper Mounting Kit 107 101 Side Mounted Doub le W all Hopper 107 101 103 108 108 104 Back Mounted Double W all Ho pper 109 107 107 109 107 107 110 110 Ref.
Parts 312747L 27 256170, Universal Hopper Fluid Outlet Kit * Parts used for 50 :1 pumps only . † P ar ts u sed with 70:1 pumps on ly . 216 210 209 207 205 204 203 202 206 207 208 201 211 215 212 Apply sealant to all non-swiv eling pipe threads. Do not use pipe sealant on swiv el fittings.
Accessories 28 312747L Accessories 262820, Flexib le Fluid Connection Kit F or gr avity f eed ing from 20 gallon hopper to propor- tioner with Xtreme lo wer . 256257, 240V 1 PH Immers ion Heater Kit F or non-e xplosiv e atmosphere s only . Includes re-settab le o v er temperatur e s witch.
Technical Data 312747L 29 Te c h n i c a l D a t a Dimensions Hopper 20 Gallon Heated Compat ible Hopper 256233 Maximum (con tinuous) temperature rating . . . . . . . . . . . . 140°F (60° C) Maximum pressu re rating (outer cavity) . . . . . . . . . .
Technica l Data 30 312747L Hopper Stand Hopper on Stand 36 in. (914 mm) 14.5 in. (368 mm) 26.5 in. (673 mm) 1.5 in. (38 mm) 17.5 in. (445 mm) 1.5 in. (38 mm) ti19011a 42.
Technical Data 312747L 31.
All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. For patent information, see www.graco.com/patents.
Een belangrijk punt na aankoop van elk apparaat Graco 255963 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Graco 255963 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Graco 255963 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Graco 255963 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Graco 255963 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Graco 255963 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Graco 255963 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Graco 255963 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
