Gebruiksaanwijzing /service van het product TPC-660G van de fabrikant AMD
Ga naar pagina of 80
TPC-660G AMD LX800 T ouch Panel Computer with 6.4” VGA TFT LCD User Manual.
TPC-660G User Manual ii Copyright The documentation and th e software included with this product are copy- righted 2004 by Advantech Co., Lt d. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time wi thout notice.
iii Product W arranty (1 year) Advantech warrants to you, the original purchaser , that each of its prod- ucts will be free from defects in ma terials and workman ship for one year from the date of purchase.
TPC-660G User Manual iv CE This product has passed the CE test for environmental specificati ons when shielded cables are used for external wiring. W e recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering inform ation.
v Packing List Before setting up the system, check that the items listed below are included and in g ood condition. If any item d oes not accord w ith the table, please contact y our dealer immediately .
TPC-660G User Manual vi 13. Never open the equi pment. For safety reasons, the equipment should be opened only by qualifi ed service personnel. 14. If one of the following si tuations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged.
vii Table of Contents Contents Chapter 1 General Information ....................................... 2 1.1 Introduction ............ ............................ ............ ........... ........ 2 1.2 Specifications ............ .....................
TPC-660G User Manual viii Figure 4.11:Install Wizard - 1 .... ........... ........... ........... 25 Figure 4.12:Install Wizard - 2 ..... ........... ........... ........... 26 Figure 4.13:Install Wizard - 3 ..... ........... ........... ........... 26 Figure 4.
ix Table of Contents Figure E.2:Install Wi zard - 1 ..... ........... ......... ........... .. 60 Figure E.3:Instal l Wizard - 2 ............... ........... ......... .... 61 Figure E.4:Instal l Wizard - 3 ............... ........... ......... .... 61 E.
TPC-660G User Manual x.
2 CHAPTER 1 General Information This chapter gives b ackground infor- mation on TPC-660G .. Sections include: • Introduction • Specifications • I/O Ports Arrangement • Panel Mounting • Explo.
TPC-660G User Manual 2 Chapter 1 General Information 1.1 Introduction The TPC-660G touch panel computer is a state-of-the-art HMI (Human Machine Interface).
3 Chapter 1 1.2 Specifications 1.2.1 System Kernel • CPU: GeodeLink Cont rol Processor LX800 500MHz • BIOS: A ward 512KB flash memo ry • South Bridge: GeodeLink Control Processor CS5536 • VGA: GeodeLink C ontrol Processor LX800 50 0MHz • Ethernet: Realtek R TL8100BL; IEEE 802.
TPC-660G User Manual 4 1.3 LCD Specifications • Display T y pe: TFT color LCD • Size (diagonal): 6.4” • Maximum Resolution: 640 x 480 (VGA) • Maximum Colors: 256,000 • Pixel Pitch (W x H, mm): 0.
5 Chapter 1 1.6 I/O Port s Arrangement The arrangement of the I/O ports is shown in Figure 1.1. Figure 1.1: I/O Port Arrangement 1.7 Panel Mounting 1. There is an adhesive waterproof gasket on the Mg-AL front bezel. Make sure the waterproof gasket is in position befo re installing TPC-660G into the panel opening.
TPC-660G User Manual 6 Figure 1.2: Panel Mounting 1.8 Exploded Diagram Figure 1.3: Assembly (exploded).
7 Chapter 1 1.9 Dimensions and Cutout • W eight: 0.8 kg • Dimensions: 195 x 148 x 44.5 mm (W x H x D) • Cutout: 188 x 141 mm (suggest ed) Figure 1.
TPC-660G User Manual 8.
2 CHAPTER 2 System Setup This chapter provides a brief explana- tion for operating TPC-660G ..
TPC-660G User Manual 10 Chapter 2 System Setup Y ou can quickly get up and running by follow ing the step-by-step instruc- tions below . 1. Unpack the TPC-660G package. Please check the packing list at the beginning of this manual to make sure every item is there.
11 Chapter 2 3. Connect the power connector to the 24 VDC power lines. The power lines can ei ther be from so me power adapter or an in-house power source.
TPC-660G User Manual 12 4. Plug the power lines into the system power receptor . Figure 2.5: Pl ugging in the Power Line 5. T urn on the System Figure 2.
13 Chapter 2 Figure 2.7: Bootup Screen 6. Calibrate the touchscreen. The de tailed procedure is described in the appendix. Note: When turning on the system, the bootup screen before entering any operating system is shif t to the right side as the phot o belo w .
TPC-660G User Manual 14.
2 CHAPTER 3 System Engine.
TPC-660G User Manual 16 Chapter 3 System Engine T able 3.1: Mainboard Connectors & Jumper Settings Label Funct ion Description CN1 LCD POWER LCD INVERTER Connector CN2 CF Compa ctFlash soc ket CN3 IDE Internal IDE 44p in (2mm) connector CN4 USB1 T wo USB T ype-A Female to on panel.
17 Chapter 3 Figure 3.1: Main Board Connect ors - 1 Figure 3.2: Main Board Connect ors - 2.
TPC-660G User Manual 18.
2 CHAPTER 4 Sof tware Configuration Sections include: • VGA Driv er Installat ion • Advantech COM Installation • Entertainment Encryp tion/ Decryption Driver Installation.
TPC-660G User Manual 20 Chapter 4 Sof tware Configuration A support CD-ROM for TPC-660G is available and along with the prod- uct. There are related utilities and drivers of TPC-660G for W in dows XP .
21 Chapter 4 Figure 4.2: Update D river Step 3: Then follow the update wizard processures. Figure 4.3: Update Wizard-1.
TPC-660G User Manual 22 Figure 4.4: Update W izard-2 Figure 4.5: Update Wizard-3.
23 Chapter 4 Figure 4.6: Update W izard-4 Figure 4.7: Update Wizard-5.
TPC-660G User Manual 24 Figure 4.8: Update W izard-6 Step 4: After you successfully upda te the driver , you can see the VGA successfully installed from the device mana ger .
25 Chapter 4 4.2 Entert ainment Encryption/Decryp tion Driver Step 1: Insert the CD-ROM and go to “Device Manager”. Click “Enter- tainment Encryption/ Decryption C ontroller” Figure 4.10: Device Manager Step 2: Following t he install shie ld wizard to finish the setup.
TPC-660G User Manual 26 Figure 4.12: Install W izard - 2 Figure 4.13: Install W izard - 3.
27 Chapter 4 Step 4: The driver is successfully installed. Y ou can check via “Device Manager” as the below . Figure 4.14: Driver Installation Complete.
TPC-660G User Manual 28.
2 CHAPTER 5 F e a t u r e s i n Windows XP Embedded Sections include: • EWF • HORM • Advantech U tilities.
TPC-660G User Manual 30 Chapter 5 Features in Windows XP Embedded TPC-660G supports the embedded Wi ndows platform. This sectio n out- lines the importan t featur es (EWF and HORM), that are provided in W in- dows XP embedded. 5.1 EWF EWF stands for Enhanced W rite Filter .
31 Chapter 5 5.2 HORM HORM stands for Hibernate Once R esume Many . In HORM environ- ment, a single hi bernation file is used to boot th e system repeatedly . T o set a HORM environment, pleas e follow the steps below . Please make sure EWF is disabled.
TPC-660G User Manual 32 5.3.1 V ersion Information Start menu-> All Programs -> Advantech This states the current XPE runtime information in cluding hardware plat- form, version, bui ld number , release date, XPE QFEs installed in compo- nent database and XP Pro Patches you in stalled manually .
2 APPENDIX A Serial Port Settings.
TPC-660G User Manual 34 Appendix A Serial Port Settings There are two serial ports, COM1 an d COM2, on TPC-660G . The serial port, COM1, supports stan dard RS-232 and the serial port COM2 on the TPC-660G is adjustable. It can be set to RS-232, RS-422 or RS-485.
35 Appendix A A.2 Dat a Format Control Setting (SW2) PIN RS-232 RS-422 RS-485 1 NDCD TX- D- 2 NRX TX+ D+ 3N T X R X + 4 NDTR RX- 5 GND GND GND 6 NDSR 7N R T S 8 NCTS 9 NRI Function 1 2 Data Format 3 4.
TPC-660G User Manual 36 A.3 Baud Rate Setting (SW3) X = On 0 = Off *= Default Baud Rate 12345678 1200 bps X 0000000 2400 bps 0 X 000000 4800 bps 00 X 00000 * 9600 bps 000 X 0000 19.
2 APPENDIX B W atchdog T imer Programming.
TPC-660G User Manual 38 Appendix B W atchdog T imer Programming B.1 Overview The TPC-660G watchdog timer can be used to monitor system software operation and take correc tive action if the software fails to functio n after the programmed period. This section descri bes the operation of the watchdog timer, and how to program it.
39 Chapter B B.2 W atchdog Timer Programming The I/O port address of the watchdog timer is 2E(hex) and 2F(hex), 2E (hex) is the address port. 2F(hex) is the data port. Y ou must fi rst assign the address of register by writing addr ess value into address port 2E(hex), then write/read data to/from the assigned reg ister through data port 2F (hex).
TPC-660G User Manual 40 T able B.1: W atchdog T imer Registers Address of register (2E) Attribute Description Read/Write V alue (2F) and description 87 (hex) ----- W rite th is address to I/O address port 2E (hex) twice to unlock the W83627HF 07 (hex) write Write 08 (hex) to select register of watchdog timer .
41 Chapter B B.3 Example Programs 1. Enable watchdog timer and set 10 sec. as timeout interval ;-------- --------- -------- --------- ---------- --------- ------ Mov dx,2eh ; Unlock W83627HF Mov al,87.
TPC-660G User Manual 42 Out dx,al Inc dx Mov al,10 Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; lock W8 3627HF Mov al,0aah Out dx,al 2.
43 Chapter B Out dx,al Inc dx In al,dx Or al,08h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Set timeout interval as 5 minutes and start co unting Mov al,0f6h.
TPC-660G User Manual 44 Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Enable watchdog timer to be reset by mouse Mov al,0.
45 Chapter B Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Enable watchdog.
TPC-660G User Manual 46 ;-------- --------- -------- --------- ---------- --------- ------ Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;-------- ---.
2 APPENDIX C W atchdog T imer Programming on WinCE.
TPC-660G User Manual 48 Appendix C W atchdog T imer Program- ming on WinCE There is a built-in watchdog timer in Windows CE 4.2 for TPC-660G . Y ou can access it through the WIN32 API. TPC-6 60G provides a WD T driver to allow users to enable/disable the watc hdog timer .
49 Appendix C C.1.1 Parameters • hDevice [in] Handle to the device that is to perform the operation. Call the Cre- ateFile function to obt ain a device handle.
TPC-660G User Manual 50 C.2 How to Use the Control Code There are 6 control codes for the op eration codes in the WDT driver . C.2.1 IOCTL _WDT_ENABLE: Enables the watchdog timer of your appl ication.
51 Appendix C C.2.4 IOCTL_WDT_GETTIMEOUT : Gets the W atchdog time setting . lpInBuffer: unused. nInBufferSize: unused. lpOutBuffer: The DWORD po ints to your wa tchdog time setting .
TPC-660G User Manual 52 C.3 Examples #define WDT_CODE(ID) CTL_CODE(FILE_DEVICE_UNKNOWN,ID , METHOD_BUFFERED, FILE_ANY_ACCESS) #define IOCTL_WDT_ENABLE WDT_CODE (0x900) #define IOCTL_WDT_DI SABLE WDT_C.
53 Appendix C // Set the W at chdog T imer as 10 seconds. Number 2 means 10 seco nds. DeviceIoControl(m_hWDT , IOCTL_WDT_SET_TIMEOUT , &nIndex, sizeof(nIndex), NULL, 0, &dwT emp, NULL); // Enable the W atchdog ti mer DeviceIoControl(m_hWDT , IOCTL_WDT_ENABLE, NULL, 0, NULL, 0, &dwT emp, NULL); While (1) { // do your job here.
TPC-660G User Manual 54.
2 APPENDIX D Accessory Kit Assembly Procedure This appendix shows how to connect to a CD-ROM via the CompactFlash slot.:.
TPC-660G User Manual 56 Appendix D Accessory Kit Assembly Procedure D.1 Comp actFlash to IDE T ransfer Kit Please follow this assembly procedur e to us e the CompactFlash slot to connect with a CD-ROM drive. 1. Connect the IDE cable to the adapter board.
57 Appendix D 2. Insert the adapter board into the Co mpactFlash slot. Figure D.3: CompactFlash Slot Figure D.4: Insert the Adapter Board into the CF slot Figure D.
TPC-660G User Manual 58 Connect the CD-ROM to the adapter board via the IDE cable and then connect the exte rnal power line to the CD-ROM. Figure D.6: Connect the CD-ROM via the IDE Cable Figure D.
2 APPENDIX E T ouchscreen Inst allation & Configuration This appendix demo nstrates how to install the touchscreen and set the con- figuration on TPC-6 60G .
TPC-660G User Manual 60 Appendix E T ouchscreen Inst allation & Configuration E.1 Driver Inst allation Please insert the x86 TPC series suppor t CD and go to the driver folder: (TPC-660GDriverUSB to uchscreen). Click setup.exe Figure E.1: Setup.exe The screen displays the installat ion wizard for the PenMount USB soft- ware.
61 Appendix E Figure E.3: Install W izard - 2 Figure E.4: Install W izard - 3.
TPC-660G User Manual 62 E.2 Uninst all the Driver Please go to Settings and then select Control Panel. Please click Add/ Remove Progr ams. Figure E.5: Uninstall -1 Select PenMount USB. Click Remo ve button. Then, select “Y es” to remove the PenMountUSB driver and reboot the system .
63 Appendix E E.3 T ouchscreen Calibration The “PM”, the i con of the PenMount Control Panel, is in the menu b ar after the touchscreen installation. Pl ease click the icon “PM” to call Pen- Mount Control Panel. It contains six fun ctions: Calibrate, Draw , Option, and About.
TPC-660G User Manual 64 Figure E.8: S tandard Calibration -2 Figure E.9: S tandard Calibration -3.
65 Appendix E Advanced Calibration is for the aged tou chscreens by using 4, 9, 16 or 25 points to calibrate touch panel. Figure E.10: Advan ced Calibration -1 Note T ouch the re d squares in sequence. The cali- bration is completed af ter the fifth to uch red point is calibrated.
TPC-660G User Manual 66 Figure E.1 1: Adva nced Calib ration -2 Figure E.12: Plot Cal ibration Data.
67 Appendix E Draw This is to test the touchscreen operation. Its display show s touch loca- tion. Figure E.13: Draw Click “menu” and then click “clear screen” to clear the drawing.
TPC-660G User Manual 68 Figure E.14: Clear Screen Option This option is to set the operati on mode and beep sounds if enabled. The operation mode, stream mode and poin t mode, is to enab le/ disable the mouse’ s ability to drag on-screen ic ons. Stream mode lets the mouse function as normal and d ragging onscreen.
2 APPENDIX F Fuse S pecifications.
TPC-660G User Manual 70 Appendix F Fuse S pecifications F .1 Fuse Specifications Rating : 250 V AC, 3.15 A Size: 5 x 20 mm F .2 Fuse Replacement Step 1: Remove the fuse cover Step 2: Replace the damaged fuse with a new one Step 3: Place the fuse co ver back into position.
Een belangrijk punt na aankoop van elk apparaat AMD TPC-660G (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen AMD TPC-660G heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens AMD TPC-660G vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding AMD TPC-660G leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over AMD TPC-660G krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van AMD TPC-660G bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de AMD TPC-660G kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met AMD TPC-660G . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
