Gebruiksaanwijzing /service van het product H3114 van de fabrikant Grizzly
Ga naar pagina of 28
ROUTER TABLE MODEL H3114 INSTRUCTION MANUAL COPYRIGHT © DECEMBER 2002 BY GRIZZLY INDUSTRIAL, INC WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints.
TABLE OF CONTENTS PAGE 1. SAFETY ....................................................................................................................... ...............................2 SAFETY INSTRUCTIONS FOR POWER TOOLS .............................
-2- H3114 Router Table SECTION 1: SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.
H3114 Router Table -3- 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size must be in accor- dance with the chart below. The amperage rating is listed on the motor or tool name- plate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
-4- H3114 Router Table 1. HAND POSITIONING. Never pass your hands directly over, or in front of the cutter. As one hand approaches cutter, move it in an arc motion away from the cutter to the outfeed side and reposition that hand beyond the cut- ter. 2.
H3114 Router Table -5- SECTION 2: INTRODUCTION We are proud to offer the Grizzly Model H3114 Router Table. The Model H3114 is part of a grow- ing Grizzly family of fine woodworking machinery.
-6- H3114 Router Table SECTION 3: CIRCUIT REQUIREMENTS General Electrical The power switch ( Page 7, Figure 2 ) on the Model H3114 is designed to work with most routers and other electrical accessories.
H3114 Router Table -7- Main Features SECTION 4: SET UP Set up and operation instructions will be easier to understand if you become familiar with the location and names of the basic features shown in Figure 2 . Figure 2. Machine features. Extension Table Power Switch Note–Only 1 of the 5 table inserts are shown.
-8- H3114 Router Table Assembly Figure 3. Aligning an extension table with the main table. To attach the extension tables and legs to the main table: 1. Place the main table upside down on a work- bench. 2. Align the extension tables mounting holes with the mounting holes on the edge of the main table ( Figure 3 ).
H3114 Router Table -9- To check the flushness of the table: 1. Place a straightedge across both extension tables and the main table. The straightedge should sit flush on all three surfaces as shown in Figure 6 .
-10- H3114 Router Table Figure 7. Router positioned correctly for "Method 1" installation. 3. Rotate the router until the main table mount- ing holes align with the mounting holes in the router base. Note—Orient the router so the adjustment controls are easy to reach.
H3114 Router Table -11- Figure 11. Correct spring placement. Figure 12. Correctly installed guard. Figure 10. Correctly clamped router. 2. Insert the retractable guard into the fence and secure the guard with the supplied M4 x 12 tap screw and the M5 flat washer ( Figure 12 ).
-12- H3114 Router Table Figure 13. Installing the pocket jointing fence. Figure 14. Securing the fence to the main table. 3. Slide the pocket jointing fence into the slot in the face of the main fence as shown in Figure 13 . 4. Secure the pocket jointing fence to the main fence with the supplied M8-1.
H3114 Router Table -13- Figure 16. Router table mounting holes. Figure 17. Miter gauge components. Figure 18. Assembled miter gauge. To secure the router table to a workbench: The bottom of each leg has two holes ( Figure 16 ) used for mounting the router table to the work- bench.
-14- H3114 Router Table 5. Loosen the threaded knobs that secure the main fence. 6. Place a straightedge across the entire face of the pocket jointing fence and adjust the main fence until the outside diameter of the router bit just touches the straightedge ( Figure 20 ).
H3114 Router Table -15- 6. Tighten the main fence threaded knobs. 7. Double check that the router is secured to the table. If it is, the router table is ready for use. Groove cutting: Beading is commonly defined as cutting a groove or bead in the face of a board.
-16- H3114 Router Table 7. Tighten the main fence threaded knobs. 8. Double check that the router is secured to the table. If it is, the router table is ready for use. Profile cutting with pilot bits: Router bits with ball bearings are called pilot bits.
H3114 Router Table -17- SECTION 5: REFERENCE INFO If you need parts or help in assembling your machine, or if you need operational information, call the Grizzly Service Department.
-18- H3114 Router Table 1 2 3 5 8 10 11 12 13 15 16 17 18 20 21 22 19 23 24 8 25 26 27 28 PARTS BREAKDOWN AND LIST.
H3114 Router Table -19- 1 PH3114001 EXTENSION TABLE 2 PH3114002 LEG 3 PH3114003 MAIN TABLE 5 PH3114005 MITER BODY 6 PH3114006 SWITCH 8 PS40 #10-32 x 3/4" TRUSS HD PHLP SCR 10 PN29 #10-32 HEX NUT (KEPS) 11 PB09M M8-1.25 x 20 HEX BOLT 12 PH3114012 POCKET JOINTING FENCE 13 PH3114013 MAIN FENCE 15 PH3114015 M8-1.
-20- H3114 Router Table NOTES.
H3114 Router Table -21- NOTES.
-22- H3114 Router Table Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
CUT ALONG DOTTED LINE 9. How many of your woodworking machines are Grizzly? _____________ 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8&qu.
Place Stamp Here FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_____________________________.
.
Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! -OR- • SECURE ORDERING • ORDERS SHIPPED WITHIN 24 HOURS • E-MAIL RESPONSE WITHIN ONE HOUR Visit Our Website T oday And .
Een belangrijk punt na aankoop van elk apparaat Grizzly H3114 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Grizzly H3114 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Grizzly H3114 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Grizzly H3114 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Grizzly H3114 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Grizzly H3114 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Grizzly H3114 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Grizzly H3114 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
