Gebruiksaanwijzing /service van het product AD-840 van de fabrikant American Dryer Corp.
Ga naar pagina of 20
AD-840 Electrical Troubleshooting Manual 1998 American Dryer Corporation 88 Currant Road Fall River , MA 02720-4781 T elephone: (508) 678-9010 / Fax: (508) 678-9447 E-mail: techsupport@amdry .
Retain This Manual In A Safe Place For Future Reference American Dispensing Company products embody advanced concepts in engineering, design, and safety . If this product is properly maintained, it will provide many years of safe, efficient, and trouble-free operation.
IMPOR T ANT YOU MUST DISCONNECT and LOCKOUT THE ELECTRIC SUPPL Y BEFORE ANY COVERS or GUARDS ARE REMOVED FROM THE MACHINE TO ALLOW ACCESS FOR CLEANING, ADJUSTING, INST ALLA TION, or TESTING OF ANY EQUIPMENT per OSHA (Occupational Safety and Health Administration) ST ANDARDS.
IMPOR T ANT The wiring diagram for the water vending machine is located behind the coin control door . W ater vending machine(s) must not be installed or stored in an area where it will be exposed to water and / or weather .
T able of Contents MICROPROCESSOR F AILURE CODES ....................................................................................... 2 1. Flow Meter ..................................................................................................
2 MICROPROCESSOR F AILURE CODES The microprocessor continually monitors the machine operation. When an error occurs the machine will display a variety of failure codes, which will lead the service technician to the potential problem. The messages displayed do not pinpoint the problem within the wiring of the machine.
3 7. SYSTEM PURGE DO NOT DRINK . .. this message will appear upon turn on of the machine. It is not actually a failure but an installation safeguard. This routine will flush out the preservatives that keep the R.O. Membrane contaminant free during storage.
4 ELECTRICAL PROBLEMS ASSOCIA TED with MICROPROCESSOR F AILURE CODES 1. FLOW METER ERROR The Flow Meter error message could be the result of the following: a . Flow meter failure. 1) Flow meter sensor may need replacement. 2) Flow meter housing may need replacement.
5 NOTE: When a complete flow meter is changed some reprogramming is required. The machine is relying on the information provided by the flow meter for accurate vending. The counts per gallon in the program will have to be changed along with the flow meter .
6 e . Press and hold the [4 GAL.] selection key to activate the vending bay . f . When the gallon has filled completely , release the key . g . Press the [2 GAL.
7 3. FIL TER ERROR The Filter Error message could be a result of the following: a . The sediment and/or carbon filters are in need of replacement; Monitor the pressure gauges while the machine is in operation. Determine which filter has a 10 P .S.I. differential pressure while the R.
8 4. OVERFLOW ERROR A. U.V . Light An Overflow Error triggered by the U.V . Light could be a result of the following: a . The U.V . Light is not plugged in. b . The U.V . Light is defective. c . The alarm connection to the relay board is not plugged in.
9 B. Base Float Switch An Overflow Error triggered by the Base Float Switch could be a result of the following: a . The Base Float Switch has been disconnected. b . The Base Float Switch has been triggered due to water flood in cabinet. c . The Base Float Switch has failed.
10 D. V ending Bay T ank Overflow Switch An Overflow Error triggered by the V ending Bay Overflow Switch could be a result of the following: a . The V ending Bay Overflow Switch is disconnected. b . The V ending Bay Overflow Switch has been triggered due to water not draining out of the tank.
11 5. CHNGER UNPLUG ERROR The CHNGER UNPLUG Error message could be a result of the following: a . Coin changer is unplugged. b . Defective coin changer .
12 6. SYSTEM REFILL PLEASE W AIT The System Refill Please W ait message could be a result of the water level in the containment tank is below the low level switch. If the machine is functioning correctly it should be refilling. The message will automatically reset 1 minute after the water level has reached the low level switch.
13 2. DRAIN PUMP MOTOR An inoperable drain pump could be a result of the following: a . Clogged drain b . Unplugged spill switch c . Incorrect positioning of the spill switch. d . Mechanical malfunction of the drain check valve. When the spill switch is changed it is important that it is positioned correctly .
14 3. 3/4 HP MOTOR An inoperable drain pump could be a result of the following: a . No water supply to machine b . Unplugged or defective low and/or high pressure switches c . Defective inlet solenoid d . Defective relay board e . Defective motor contactor f .
15 ELECTRICAL COMPONENTS LIST ADC Part No. Description 123000 Indicator Light - 1 15 V AC 123005 Indicator Light - 24 V AC 182455 120/240V Primary 24 V AC Secondary 150 V A 132451 Contactor - 24 V AC 133356 Power Cord - 120 V A C 137060 Arc Suppressor (A.
ADC 182731 1 - 02/25/98-25.
Een belangrijk punt na aankoop van elk apparaat American Dryer Corp. AD-840 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen American Dryer Corp. AD-840 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens American Dryer Corp. AD-840 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding American Dryer Corp. AD-840 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over American Dryer Corp. AD-840 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van American Dryer Corp. AD-840 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de American Dryer Corp. AD-840 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met American Dryer Corp. AD-840 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
