Gebruiksaanwijzing /service van het product Electric Powerhead Electroglide van de fabrikant H-P Products
Ga naar pagina of 16
ELECTROGLIDE ™ ELECTRIC POWERHEAD OWNER’S MANUAL Review this manual before operating your Electroglide Electric Powerhead.
TABLE OF CONTENTS Subject Page Safety Instructions 3 Parts and Features 4 Assembling Vacuum System 5 General Operation 6 Electroglide Attachments Handle Attachments 6 Wand Assembly Attachments 6 Perfo.
WARNING To reduce the risk of fire, electrical shock or injury: ELECTROGLIDE 3 IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using this vacuum system.
4 ELECTROGLIDE It is important to know your Electroglide parts and features to assure its proper and safe use. Review these before using your Electroglide. WARNING Always unplug the Electroglide before cleaning the brush area as brush may suddenly restart.
ELECTROGLIDE 5 Before assembling your Electroglide Electric Powerhead, be sure you have all parts shown in PARTS AND FEATURES. 1. Connect the upper and lower wand sections. (The wand swivel is located on the lower wand.) 2. Slide the upper and lower wands together until the wand button snaps into place.
6 ELECTROGLIDE GENERAL OPERATION Hose Handle Attachments If the Electroglide is attached, turn cleaner OFF before removing hose handle from wands. 1. Press lock button, then pull to remove handle from wand. 2. Slide attachments firmly on handle as needed.
Handle Release Pedal ELECTROGLIDE 7 Edge Cleaner Active brush edge cleaners are on both sides of the Electroglide. Therefore, guide either side of the Electroglide along baseboards or next to furniture to help remove dirt trapped at carpet edges.
Light Bulb Replacemnent 1. Disconnect cleaner from electrical outlet. 2. Remove light cover by pressing in and lifting both sides of cover as shown. WARNING Always unplug electrical cord and vacuum hose before servicing and maintaining the Electroglide Electric Powerhead.
Base Brush Support Tab ELECTROGLIDE 9 MAINTENANCE AND CARE To r emov e belt: 1. Remove light cover and light bulb as shown on Page 8. 2. Unscrew the Electroglide Powerhead cover screws. Belt Removal and Replacement The belt should also be checked periodically to be sure it is in good condition.
10 ELECTROGLIDE Belt Removal (continued) 6. Remove worn belt. 7. Slide brush supports off to check and clean brush support areas. MAINTENANCE AND CARE To replace belt: 1. Slide washers and brush supports onto brush assembly. 2. Install new belt over motor drive, then over brush sprocket.
ELECTROGLIDE 11 MAINTENANCE AND CARE Belt Replacement (continued) 5. Tilt cover to back. Press cover firmly until side tabs snap into place. Replace cover screws, light bulb and light cover. Brush Replacement 1. Remove the Electroglide Powerhead cover, belt and brush assembly.
12 ELECTROGLIDE ELECTROGLIDE REPLACEMENT PARTS.
ELECTROGLIDE 13 ELECTROGLIDE REPLACEMENT PARTS Illus. No. 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Part No. 7922 7923 7972 7925 7926 7927 7967 7965 7929 7930 7931 7932 7933 7.
14 ELECTROGLIDE LIMITED W ARRANTY H-P PR ODUCTS, INC. warrants that the Electroglide Electric Po werhead, when used for household purposes, pursuant to Seller’s instructions, will be free from defects in materials and workmanship for a period of one year from the date of the initial consumer purchase.
ELECTROGLIDE 15 H-P PRODUCTS, INC. 512 W. GORGAS STREET LOUISVILLE, OHIO 44641 SERVICE INFORMATION The instructions in this booklet serve as a guide to routine maintenance. If additional service or repairs are required, please call 1-800-822-8356 for your nearest authorized service dealer.
H-P Products, Inc. 512 W. Gorgas Street Louisville, Ohio 44641-0912 HVS-968 -NL 0 2 /0 2 ®.
Een belangrijk punt na aankoop van elk apparaat H-P Products Electric Powerhead Electroglide (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen H-P Products Electric Powerhead Electroglide heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens H-P Products Electric Powerhead Electroglide vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding H-P Products Electric Powerhead Electroglide leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over H-P Products Electric Powerhead Electroglide krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van H-P Products Electric Powerhead Electroglide bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de H-P Products Electric Powerhead Electroglide kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met H-P Products Electric Powerhead Electroglide . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
