Gebruiksaanwijzing /service van het product HS233 van de fabrikant Hanns.G
Ga naar pagina of 21
HS233 HSG 1 155.
User ’ s Manual OSD[4.393] 2 Before operating the monitor, please read this ma nual thoroughly. This manual should be retained for future reference. This device complies with requirement of EMC directive 2004/108/EC with regard to Electromagnetic Compatibility , and 73/23/EEC and 93/ 68/EEC with regard to Low V oltage directive.
User ’ s Manual 3 RECYCLING INFORMATION We, the Hanns.G care very much about our environment prot ection strategy and firmly believe that it helps us have healthier earth via appropriate treatment and recycling of industrial technology devices at the end-of-life.
User ’ s Manual 4 T A BLE OF CONTENTS SAFETY NOTICE .................................................................................................. 5 PRECAUTIONS ....................................................................................
User ’ s Manual 5 SAFETY NOTICE 1. The changes or modifications not expressly approved by the pa rty responsible for compliance could void the user's authority to operate the equipm ent. 2. Shielded interface cables and AC pow er cord, if any , must be used in order to com ply with the emission limits.
User ’ s Manual 6 SPECIAL NOTES ON LCD MONITORS The following symptoms are norm al with LCD monitor and do not indicate a problem. Due to the nature of the fluorescent light, the sc reen may f licker during initial use. T urn off the Power Switch and then turn it on again to make sure the flicker disappears.
User ’ s Manual 7 BEFORE YOU OPERA TE THE MONITOR FEA TURES 58,4cm / 23” W ide Screen TFT Color LCD Monitor Crisp, Clear Display for W indows GP Green Product Ergonom ic Design .
User ’ s Manual 8 INST ALLA TION INSTRUCTIONS I N S T A L L R E M O V E Figure.1. Installing and Removing the Base INSTALLATION: 1. Carefully place the monitor face down on a soft and flat surface (blanket, foam , cloth, etc) to prevent any damage to the monitor .
User ’ s Manual 9 SETTING THE MONITOR ON THE W ALL DISSEMBLING THE ST AND BASE: 1. Disconnect all the cables and cords from the Monitor to prevent damage. 2. Carefully place the monitor face down on a soft and flat surface (blanket, foam , cloth, etc) to prevent any damage to the monitor .
User ’ s Manual 10 MAKING CONNECTIONS CONNECTING TO A PC T urn off your computer before performing the procedure below . 1. Connect one end of the VGA cable to the back of the monitor and connect the other end to the computer ’ s VGA port.
User ’ s Manual 11 ADJUSTING THE VIEWING ANGLE For optim al viewing it is recommended to look at the full face of the monitor , then adjust the monitor ’ s angle to your own preference. Hold the stand so you do not topple the m on itor when you change the monitor ’ s angle.
User ’ s Manual 12 OPERA TING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or of f. The other control butt ons are located on the front panel of the monitor (See Figu re 4). By changing these settings, the picture ca n be adjusted to your personal preferences.
User ’ s Manual 13 FRONT P ANEL CONTROL Power Button: Press this button to switch ON/OFF of m onitor ’ s power . Power Indicator: Blue — Power On mode. Orange — Power Saving mode. MENU: 1. T urn the OSD menu on. 2. Enter sub menu when OSD menu is ON.
User ’ s Manual 14 HOW T O ADJUST A SETTINGS PICTURE BRIGHTNESS Adjust the brightness value of the display according to your preference. Select 「 BRIGHTNESS 」 option to adjust the brightness value. CONTRAST Adjust the contrast value of the display accordin g to your preference.
User ’ s Manual 15 DCR Select the 「 DCR 」 option to switch the function On or Of f ECO Select the 「 ECO 」 option to switch the function On or Of f. SHARPNESS Select the 「 SHARPNESS 」 option to adjust the sharpness of the display . Set the value from 0 to 100.
User ’ s Manual 16 PLUG AND PLA Y Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B c apa bilities according to the VESA DDC ST ANDARD. It allows the monitor to inform the host system of its identity and, depe nding on the level of DDC used, communicate additional information about its display capabilities.
User ’ s Manual 17 TECHNICAL SUPPOR T (F AQ) Q & A FOR GENERAL PROBLEMS PROBLEM & QUESTION POSSIBLE SOLUTION Power LED is not on *Check if the Power Switch is in the ON position. *Power Cord should be connected. No Plug & Play *Check if the PC system is Plug & Play compatible.
User ’ s Manual 18 Addendum related to Windows 7 When you encounter display problem under Windows 7, you need to do the following: 1. Make sure your PC computer (Hardw are requirement) can support Windows 7. 2. Make sure your video ca rd can run Windows 7.
User ’ s Manual 19 ERROR MESSAGE & POSSIBLE SOLUTIONS CABLE NOT CONNECTED: 1. Check that the signal-cable is properly connect ed, If the connector is loose, tighten the connector ’ s screws. 2. Check the signal-cable’ s connection pins for damage.
User ’ s Manual 20 (HDMI INPUTS) Primary V ideo Format T imings MODE RESOLUTION 1 640 × 480p @ 60Hz 2 720×480p @ 60Hz 3 1280×720p @ 60Hz 4 720×576p @ 50Hz 5 1280×720p @ 50Hz 6 1920×1080i @ 60H.
User ’ s Manual 21 APPENDIX SPECIF ICA TIONS Driving system TFT Color LCD Size 58,4 cm / 23”Diagonal LCD Panel Pixel pitch 0.2655 mm(H) x 0.2655 mm(W) H-Frequency 30 kHz – 83 kHz Analog Signal Input V -Frequency 55 Hz – 76 Hz H-Frequency 30 kHz – 138 kHz (For Nvidia 3D mode up to 137.
Een belangrijk punt na aankoop van elk apparaat Hanns.G HS233 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hanns.G HS233 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hanns.G HS233 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hanns.G HS233 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hanns.G HS233 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hanns.G HS233 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hanns.G HS233 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hanns.G HS233 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
