Gebruiksaanwijzing /service van het product Flextight 343 van de fabrikant Hasselblad
Ga naar pagina of 22
User's Guide Flextight 343 English.
© 2004 Hasselblad A/S. All rights reserved. Flextight 343 User's Guide, Part No 70030051, revision A. The information in this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Hasselblad A/S.
Table of Contents User's Guide - Flextight 343 Table of Contents 3 English Hardware Reference - Flextight 343 5 Warnings and Restrictions 6 System Requirements 6 Front Panel 7 Back Panel & Co.
User's Guide - Flextight 343 4 English.
Hardware Reference - Flextight 343 This manual provides important information about using your Flextight 343 scanner. Topics include: • Important warnings and restrictions • System requirements .
Warnings and Restrictions • Read all of the included documentation before attempting to install and use the scanner. • Do not touch the originals and/or the original holder while scanning. • Do not start scanning or previewing until an original holder with an original has been mounted.
Front Panel A Feed Table: place original holders here for scanning. The table can be folded up to keep dust from entering the scanner and to keep it out of the way.
Back Panel & Connectors A Power Cable Socket: plug the power cable into this socket. B FireWire Interface Sockets: plug a FireWire cable (max. 6 m) here and connect it to your computer. You can use the second plug to connect another device (hard disk, printer etc.
Cut-Away View A CCD Plate: this platform contains the light sensor. B Optics: focuses the image of the original on the CCD. C Drum: rotates the original into the scanner and steps it past the CCD line of focus. D Light Tube: illuminates the transparent originals.
Setting up the Scanner Environmental Requirements Set up the scanner in a location that fulfils the following requirements: • Keep the scanner away from sources of heat, such as direct sunlight or a radiator. Warm temperatures will degrade the quality of your scans - for best results, work in a cool environment.
Installation Procedure, FireWire Interface 1. Place the scanner on a table near your computer with the front facing away from you. Make sure that the location you choose meets all environmental - and electrical requirements as described on page 10. 2.
User's Guide - Flextight 343 Hardware Reference - Flextight 343 12 Operating the Scanner English FLEXTIGHT ORIGINAL HOLDER PA TENT PENDING à à A B E D C G H J F Figure 4: Operating the Flextigh.
Operating the Scanner (See Figure 4 opposite). 1. It is assumed that the scanner and FlexColor software have been properly installed. 2. Pull the feed table (B) down to scan position. 3. Press the power button (G) on the front of the scanner to switch it on.
Resolutions True Optical Resolutions The table below shows the true optical resolutions (in ppi) available with each of the original holders. When scanning at one of the resolution settings listed, one pixel in the scanner ’s image sensor corresponds exactly to one pixel in the final image.
Example: For an output resolution of 300 ppi, take the true resolution shown in Table 1, divide by 300 and multiply by 100%. Enter the result in the Zoom field in the main FlexColor window.
The Light Tube Orientation of the Light Tube Flextight 343 contains a light tube that illuminates your originals while scanning. The light tube is fitted with a reflective sleeve, which must be aligned correctly inside the scanner. The sleeve helps direct the light to achieve maximum illumination of the original.
Replacing the Light Tube If your scans are suddenly coming out black (or all white if you are scanning negatives), then the light tube may be defective or misaligned. Follow procedure below to replace a tube: 1. Get the appropriate replacement light tube (ask your Flextight dealer or see specification in “Technical Specifications” on page 20).
6. The light tube is clearly visible, as shown in Figure 7. Hold each end of the light tube between your thumb and index finger. Rotate the light tube until it comes free and pull it away from the scanner. Note that the light tube sockets allow the tube to be rotated all the way around, but they click into position at each quarter turn.
Cleaning the External Surface of the Scanner If the external surface of the scanner becomes dirty, then clean it with a damp cloth. Be careful not to get any moisture inside the scanner or on any of the connectors. Do not use alcohol or other solvents.
Technical Specifications Power Connector: Power Consumption Max. 60 W during operation Power Requirements 100-240V AC, 1.3A, 50-60Hz Interface to Computer FireWire (IEEE 1394) Front Panel One multifunction switch (on/off switch) and status light Drum Force 1kg (2.
FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
CE - Declaration of Conformity User's Guide - Flextight 343 Hardware Reference - Flextight 343 22 CE - Declaration of Conformity English HASSELBLAD A/S HEJREVEJ 30 DK - 2400 COPENHAGEN NV TELEPHONE +45 7026 0800 TELEFAX +45 7026 0900 REG./VAT NO.
Een belangrijk punt na aankoop van elk apparaat Hasselblad Flextight 343 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hasselblad Flextight 343 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hasselblad Flextight 343 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hasselblad Flextight 343 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hasselblad Flextight 343 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hasselblad Flextight 343 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hasselblad Flextight 343 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hasselblad Flextight 343 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
