Gebruiksaanwijzing /service van het product 303 van de fabrikant Henny Penny
Ga naar pagina of 18
odel 301/302/303 This section provides operating procedures for the Henny Pen- ny OG/OE-301/302/303. Sections 1, 2, and 3 should be read and all instructions should be followed before operating the fryer. 3-2. Figures 3-1 through 3-8 identify and describe the function of all operating controls and components.
Melt LED Ready LED Head LED Product LED Time LED Temperature LED Alarm LED When the melt LED is flashing, the fryer is in the melt cycle. When the temperature of the shortening reaches approximately 250°F (121”C), the melt LED will go off and automatically switch to the heat cycle.
3-l 3-2 3-2 3-3 3-3 &I -;j tern No. 14 15 16 17 18 19 20 I escriptiori Other LED Idle LED Up and Down Switches Fuses (electric only) High Limit Reset Contactors (electric only) Thermal Sensor The other LED flashes while in the high level program mode and special program modes only.
3-6 24 Drain Interlock (Hidden behind bracket) Drain Valve Filter Union odel The drain interlock switch is a microswitch that provides pro- tection for the heating elements in the event an operator drains shortening from the frypot while the power switch is on.
odd 0 301/302/303 Fig. NO. 3-6 3-6 3-8 3-8 Rte No. 25 Filter Drain Pan 26 Filter Pump Switch 27 Oil Return Line 28 Gas Shut-Off Valve Each cookpot has its own gas shut-off valve on thegas line (gas only) going to the gas valve. 29 30 Gas Control Valve (gas only) Gas Solenoid (gas only) Function The .
Y el 0.
0 . %.
Y 3 re 3- re.
ode! 0.
Main Power Switch The main power switch is a two,way switch. Move the switch to the position marked ON to operate the fryer. Move the switch to the position marked ON to operate the The thermostat is an electro-mechanical device used to below the temperature set by the thermostat.
It is recommended that a high quality frying shortening be used in the O&301/302/303 and OG-301/302/303 fry stations. Some low grade shortenings have a high moisture content causing foaming and boiling over. The Henny Penny OE-301/302/303 requires 48 pounds of shortening per cookpot.
4. ove power switch to the “ON” position. Unit will automatically go into the melt cycle. When the ri,~ :%; : :. ,$‘,, ‘>, temperature reaches 250°F (121OC) the control will go into the heat cycle. The shortening will be heated until the temperature setting is reached.
el 0 Frying breaded food requires frequent filtering. Taste the cold shortening every day for flavor. Watch the shortening for foaming during the frying cycle. Discard the shorten- ing as soon as it shows sign of foaming. Clean the cookpot as follows each time the shortening is changed or filtered.
enny OEI 301l3~2l303 3-5. F (~o~ti~ue~) If shortening is slow coming from faucet, it is possible that the filter connecting the union on the filter tube line is not tightened properly. If so, turn off the pump and use gloves to tighten the union. This union will be hot.
The filter pump motor is equipped with a manual reset but- ton in the event the motor’s thermal protector acuates. This reset button is located on the rear of the motor. Wait ap- proximately 5 minutes before attempting to reset this pro- tector device.
3-8. 8. Clean the top and bottom filter screen with soap and water. Rinse thoroughly with hot water. Be sure that the filter screens, crumb catcher, filter clips and the suction standpipe are thoroughly dry before assembly of filter envelope or water will dissolve the filter paper.
odel 301 l3~2l3Q3 After the initial installation of the fryer, as well as .before every change of shortening, the cookpot should be thoroughly cleaned as follows: I Melt bypass should be in operation. Refer to section 3-2 “Operating Controls” on Exit Melt Switch.
6. When the solution reaches 200”F, turn the main power switch to the OFF position. Watch cleaning solution constantly to make sure it does NOT boil over, causing damage to controls. 7. Let the cleaning solutions stand for 15 to 20 minutes with the power off.
Een belangrijk punt na aankoop van elk apparaat Henny Penny 303 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Henny Penny 303 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Henny Penny 303 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Henny Penny 303 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Henny Penny 303 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Henny Penny 303 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Henny Penny 303 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Henny Penny 303 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
