Gebruiksaanwijzing /service van het product 342 van de fabrikant Henny Penny
Ga naar pagina of 30
Model OFE/OFG/OEA/OGA-341, 342 2-1. INTRODUCTION This section provides procedures for the check out and replacement of the various parts used within the fryer. Before replacing any parts refer to the Troubleshooting Section. It will aid you in determining the cause of the malfunction.
Model OFE/OFG/OEA/OGA-341, 342 1-3. HIGH TEMPERATURE 2. Using a Phillip’s head screwdriver, remove the screws securing LIMIT CONTROL the inner heat shield and remove from unit. Figure 2-3. (Gas Units) (Continued) Figure 2-3 3. Remove the screw securing the high limit bracket to the fram e and remove the high limit and bracket from unit.
Model OFE/OFG/OEA/OGA-341, 342 2-3. HIGH TEMPERATURE LIMIT CONTROL (Gas Units) (Continued) Replacement To avoid electrical shock or property damage, move the power switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle. 1.
Model OFE/OFG/OEA/OGA-341, 342 2-4. COMPLETE CONTROL Should the control board become inoperative, follow these PANEL REPLACEMENT instructions for replacing the board.
Model OFE/OFG/OEA/OGA-341, 342 2-5. POWER SWITCH (Continued) 4. With control panel removed, and the wires off the switch, push in on tabs on the switch to remove from panel. Figure 2-12. 5. Replace with new switch, and reconnect wires to switch. 6. Replace the control panel.
Model OFE/OFG/OEA/OGA-341, 342 2-6. TEMPERATURE PROBE 5. Remove the probe from the frypot, and disconnect wire REPLACEMENT (GAS) connector from the control panel. Figure 2-15. (Continued) 6. Place the nut and new ferrule on the new probe and insert the probe into the compression fitting until it extends one (1) inch (2.
Model OFE/OFG/OEA/OGA-341, 342 2-7. TEMPERATURE PROBE 4. Using a ½ inch wrench, remove the nut on the compression REPLACEMENT fitting. Figure 2-18. (ELECTRIC) (Continued) 5.
Model OFE/OFG/OEA/OGA-341, 342 2-8. FLAME SENSOR/ PILOT / IGNITOR ASSEMBLY (Gas) (Continued) 2. Remove the control panel and heat shield from control area. Figure 2-19. Figure 2-19 3. Disconnect the flame sense wire from ignition m odule. Figure 2-20.
Model OFE/OFG/OEA/OGA-341, 342 2-9. IGNITION MODULE During normal operation, the ignition modules send 24 volts to the ignitors and gas valve. If a module does not sense a pilot flame, the module starts the ignition process again.
Model OFE/OFG/OEA/OGA-341, 342 2-10. TRANSFORMER The transformer reduces voltage down (to 24V) to accomm odate REPLACEMENT those com ponents with low voltage.
Model OFE/OFG/OEA/OGA-341, 342 2-12. VACUUM SWITCH This switch senses the airflow from the induction blower. If REPLACEMENT the airflow is reduced below a set am ount, the switch opens and the I/O board cuts power to the gas control valve, which shuts the p i l o t f l a m e o f f .
Model OFE/OFG/OEA/OGA-341, 342 2-13. DRAIN MICROSWITCH Upon turning the drain handle, the drain microswitch should REPLACEMENT “open”, cutting of f the pilot flame. This will prevent the fryer from heating while shortening is being drained from the frypot.
Model OFE/OFG/OEA/OGA-341, 342 2-14. FILTER SWITCH 3. Label and remove the wires from the switch. W ith test REPLACEMENT instrum ent check across the terminals of the switch. W ith the (Continued) switch in the on position, the circuit should be closed.
Model OFE/OFG/OEA/OGA-341, 342 2-15. GAS CONTROL VALVE REPLACEMENT (Continued) 1. Remove right side panel. Figure 2-37. Figure 2-37 2. Label and remove wires from gas valve. Figure 2-38 Figure 2-38 3. Using a 7/16 wrench, remove the pilot line from the gas valve.
Model OFE/OFG/OEA/OGA-341, 342 2-15. GAS CONTROL VALVE REPLACEMENT (Continued) 5. Using a pipe wrench, loosen the outlet fitting to the burner. Figure 2-41. Figure 2-41 6. Using a Phillips screwdriver, remove the 2 screws securing the gas valve to the bracket and remove gas valve from unit.
Model OFE/OFG/OEA/OGA-341, 342 2-16. BLOWER MOTOR REPLACEMENT (Continued) 3. Remove the wire cover from the blower m otor housing. Figure 2-44. Figure 2-44 4. Remove wire nuts connecting blower motor wires to wires in conduit. Figure 2-45. Figure 2-45 5.
Model OFE/OFG/OEA/OGA-341, 342 2-16. BLOWER MOTOR REPLACEMENT (Continued) 8. Using 3/8 inch nut driver, remove nuts securing blower to the unit. Figure 2-48. Pull blower from unit. Figure 2-48 9. Install new blower in reverse order. 2-17. HEATING ELEMENTS (ELECTRIC) Heating elements are available for 208 and 230 voltage.
Model OFE/OFG/OEA/OGA-341, 342 2-17. HEATING ELEMENTS 4. Perform an ohm check on one elem ent at a time, with wires (ELECTRIC) disconnected. The 2 elements actually have 3 small heating (Continued) elements inside the outer plate. It’s important to check between the correct wires to obtain an accurate ohm reading.
Model OFE/OFG/OEA/OGA-341, 342 2-18. HEATING Each well of an electric fryer requires two switching contactors. CONTACTORS The first in line is the prim ary contactor and the second in line is (ELECTRIC) the heat contactor. W hen open, the primary contactor does not allow power to flow to the heat contactor.
Model OFE/OFG/OEA/OGA-341, 342 2-18. HEATING CONTACTORS (ELECTRIC) (Continued) To avoid electrical shock, make connections before applying power, take reading, and remove power before removing meter leads. The following checks are performed with the wall circuit breaker closed and the main power switch in the ON position.
Model OFE/OFG/OEA/OGA-341, 342 2-18. HEATING CONTACTORS (ELECTRIC) Continued) 2. Remove the screws securing the contactor to the shroud, and remove contactor. Figure 2-55. 3. Install new contactor, and see steps 4 and 5. Figure 2-55 Replacement (Primary Contactor) 1.
Model OFE/OFG/OEA/OGA-341, 342 2-19. SPEAKER ASSEMBLY The speaker assembly emits audible signals to let the operator know when cooking and hold times are finished.
Model OFE/OFG/OEA/OGA-341, 342 2-20. HIGH TEMPERATURE This high temperature control is a safety, manual reset control, LIMIT CONTROL which senses the temperature of the shortening. If the short- (ELECTRIC) ening tem perature exceeds 425 ° F (218 ° C), this switch opens and shuts off heat to the frypot, and E10 shows in control display.
Model OFE/OFG/OEA/OGA-341, 342 2-20. HIGH TEMPERATURE LIMIT CONTROL (ELECTRIC) (Continued) 4. Pull back cardboard cover and remove the two electrical wires from the high temperature lim it control. Figure 2-66. Figure 2-66 5. Manually reset the control, then check for continuity between the two terminals after resetting the control.
Model OFE/OFG/OEA/OGA-341, 342 2-20. HIGH TEMPERATURE LIMIT CONTROL (ELECTRIC) (Continued) 4. Straighten the capillary tube, and pull capillary tube through the hole in the element hinge, from the rear of the fryer. 5. Remove the defective control from the fryer.
Model OFE/OFG/OEA/OGA-341, 342 2-21. FILTER PUMP AND 1. Remove electrical power supplied to unit. MOTOR REMOVAL To avoid electrical shock or property damage, move the power switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle.
Model OFE/OFG/OEA/OGA-341, 342 2-21. FILTER PUMP AND 7. Remove left side panel. MOTOR REMOVAL (Continued) 8. Using 9/16” socket or wrenches, remove the bolts and nuts securing the motor to the bracket and pull pump, m otor, and piping from unit. Figure 2-74.
Model OFE/OFG/OEA/OGA-341, 342 2-23. AUTOLIFT PC BOARD 1. Remove electrical power supplied to unit. REPLACEMENT (if applicable) Autolift PC Board To avoid electrical shock or property damage, move the power switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle.
Model OFE/OFG/OEA/OGA-341, 342 2-24. AUTOLIFT ACTUATOR (MOTOR) REPLACEMENT (if applicable) 5. Disconnect actuator connector. Figure 2-80. Figure 2-80 6. Remove female connector from plate. Figure 2-81. Figure 2-81 Figure 2-82 7. Using 7/16” socket, remove the 4 nuts securing the support plate.
Model OFE/OFG/OEA/OGA-341, 342 2-24. AUTOLIFT ACTUATOR (MOTOR) REPLACEMENT (if applicable) 8. Remove the 2 top screws securing the support plate and remove the plate from the unit. Figure 2-84. Figure 2-84 9. Using a 15T torx driver, remove the 2 torx screws from the back shroud, and pull the actuator from the unit.
Een belangrijk punt na aankoop van elk apparaat Henny Penny 342 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Henny Penny 342 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Henny Penny 342 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Henny Penny 342 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Henny Penny 342 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Henny Penny 342 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Henny Penny 342 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Henny Penny 342 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
