Gebruiksaanwijzing /service van het product FM07-020-F van de fabrikant Henny Penny
Ga naar pagina of 40
Kentucky Fried Chicken Computerized Control Installation, Operation, and Programming Instructions OPERA T OR MANUAL.
.
FM07-020-F Revised 08-31-07 LIMITED W ARRANTY FOR HENNY PENNY EQUIPMENT Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the original purchaser on.
T able of Content s SECTION 1. INTRODUCTION .................................................................................................... 1-1 1-1. SAFETY ..........................................................................................
SECTION 1. INTRODUCTION 1-1. SAFETY The Henny Penny pressure fryer has may safety features incorporated. However , the only way to ensure a safe operation is to fully under - stand the proper installation, operation, and maintenance procedures. The instructions in this manual have been prepared to aid you in learning the proper procedures.
1-3. INTRODUCTION Installation of the KFC Computerized Control Panel on existing Henny Penny gas pressure fryers. Disconnect the fryer from the electrical supply source before beginning panel conversion. Failure to disconnect the fryer from the supply source could result in electrical shock.
1-5. NINE-PIN CONNECTOR WIRING A. Remove the above wires from their existing position. These wires will be connected to the nine-pin connector provided. B. Locate wires number 12, 8, and 1 1 at the fan motor . Remove the connector securing these wires.
1-7. SLOT COVER When installing the computerized panel retrofit kit, it is necessary to cover the existing slot in the heat shroud. This slot allows the capillary tube of the old control panel to extend through the heat shroud when mounting the old control.
304 1-5 FIGURE 1.
1-6 30 4 FIGURE 2.
304 1-7.
1-8 30 4.
SECTION 2. OPERA TION 2.1 INTRODUCTION The KFC Programmable Controller has two fundamental modes of operation: cook and program. In the cook mode the melt, stand-by , heat, and timer functions are active. In program, these modes are set by the operator .
2-2 30 4 2-2. SWITCHES AND INDICA TORS (Continued) DROP Indicator -The display will read “DROP” when the shortening has reached the setpoint temperature. (+ 4° to -2°) T emperatur e Switch -This switch allows the operator to read t h e temperature of the shortening while in a cook cycle.
2-5. COOKING OPERA TION 1. Move the power switch to the POWER position. 2. If the display reads “LO” wait for it to change to “COOL” or display a temperature. 3. If the display reads “COOL” depress the EXIT COOL switch. 4. Depress the switch next to the cycle you wish to use.
2-6. FIL TERING THE SHOR TENING Frying breaded products requires frequent filering. After each frying cycle the display will read FILR, indicating to filter . It should be noted that further operation of the control is not allowed until filtering is complete.
2-6. FIL TERING THE SHOR TENING (Continued) 7. When the pump is pumping air only , close the filter valve first and then move the main power switch to the OFF position. 8. Being sure there is sufficient shortening in the frypot, depress the EXIT FILL switch.
.
SECTION 3. PROGRAMMING 3-1. BASIC PROGRAMMING SEQUENCE T o enter the program mode a password keystroke sequence is required. Note that when performing this sequence the switches must be depressed within one second of each other . If not, the control will not enter the program mode.
3-2. COOK CYCLE PROGRAMMING (Continued) 10. Follow steps 4, 5, and 6 until all six intervals have been programmed for pressure. The above steps may be followed for interval alarms except you cannot pr ogram an interval alarm in the first interval.
3-4. SPECIAL PROGRAMMING MODES (Continued) 3. Select the desired special function by depressing either cycle switch 6 or 7. 4. Perform the desired operation. 5. Depress the EXIT FILL switch to exit the special program mode. Unit will return to stand-by cook mode.
3-6. TEST PROCEDURE (Continued) The table below shows the corresponding switch with the output. Switch Device Activated Product One Pressure Solenoid and Heat Control Select Time Product Indicators Se.
805 3-5.
3-6 805.
805 3-7.
3-8 805.
805 3-9.
3-10 807.
805 3-1 1.
3-12 807.
807 3-13.
3-14 807.
807 3-15.
3-16 807.
807 3-17.
3-18 807.
SN: AN0703021 & ABOVE 807 3-19.
SN: AN0703021 & ABOVE 3-20 807.
SP ARE P AR TS LIST - GAS Part No. Description T o ensure the correct control replacement kit is shipped for gas fryers built before 8-16-06, the model and serial number must be provided.
SP ARE P AR TS LIST - ELECTRIC Part No. Description T o ensure the correct control replacement kit is shipped for electric fryers built before 8-16-06, the model and serial number must be provided.
Een belangrijk punt na aankoop van elk apparaat Henny Penny FM07-020-F (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Henny Penny FM07-020-F heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Henny Penny FM07-020-F vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Henny Penny FM07-020-F leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Henny Penny FM07-020-F krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Henny Penny FM07-020-F bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Henny Penny FM07-020-F kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Henny Penny FM07-020-F . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
