Gebruiksaanwijzing /service van het product CPWX12WN van de fabrikant Hitachi
Ga naar pagina of 242
1 Projector CPX10WN/CPX11WN/ CPWX12WN User's Manual (detailed) Operating Guide Thank you for purchasing this projector . ► Before using this product, please read all manuals for this product. Be sure to read Safety Guide rst. After reading them, store them in a safe place for future reference.
1 About The Symbols V arious symbols are used in this manual, the user ’s manual and on the product itself to ensure correct usage, to prevent danger to the user and others, and to prevent property damage. The meanings of these symbols are described below .
2 Safety Precautions W ARNING Never use the projector if a problem should occur . Abnormal operations such as smoke, strange odor , no image, no sound, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter , etc.
3 W ARNING Be cautious of High temperatures of the projector . High temperatures are generated when the lamp is lit. It could result in fire or burn. Use special caution in households where children are present. Do not touch about the lens, air fans and ventilation openings during use or immediately after use, to prevent a burn.
4 W ARNING Be careful in handling the light source lamp. The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector ’ s vent holes.
5 Safety Precautions (continued) CAUTION Be careful in moving the projector . Neglect could result in an injury or damage. • Do not move the projector during use. Before moving, disconnect the power cord and all external connections, and close the slide lens door or attach the lens cap.
6 Safety Precautions (continued) NOTE Do not give the remote control any physical impact. A physical impact could cause damage or malfunction of the remote control. • T ake care not to drop the remote control. • Do not place the projector or heavy objects on the remote control.
7 Safety Precautions (continued) NOTE About consumables. Lamp, LCD panels, polarizors and other optical components, and air filter and cooling fans have a different lifetime in each. These parts may need to be replaced after a long usage time. • This product isn’t designed for continuous use of long time.
8 • If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer .
9 Regulatory Notices FCC Statement W arning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
2 Contents Introduction ............... 3 F e a t u r e s ...................... 3 Checking the contents of package ... 3 P a r t n a m e s .................... 4 Setting up . ............... . 7 Arrangement ................... 7 Connecting with your devices .
3 Introduction • Keep the original packing materials, for future reshipment. Be sure to use the original packing materials when moving the projector . Use special caution for the lens. • The projector may make a rattling sound when tilted, moved or shaken, since a ap to control the air ow inside of the projector has moved.
4 Introduction Par t names (1) Lamp cover ( 93 ) The lamp unit is inside. (2) FOCUS ring ( 24 ) (3) ZOOM ring ( 24 ) (4) Control panel ( 5 ) (5) Elevator buttons (x 2) ( 24 ) (6) E.
5 Introduction Part names (continued) (continued on next page) CONTROL MONITOR OUT AUDIO OUT AC IN LAN HDMI USB DC5V 0.5A TYPE A USB TYPE B COMPUTER IN1 COMPUTER IN2 S-VIDEO VIDEO AUDIO IN2 AUDIO IN1 .
6 Introduction Part names (continued) Remote control (1) VIDEO button ( 22 ) (2) COMPUTER button ( 22 ) (3) SEARCH button ( 23 ) (4) ST ANDBY / ON button ( 19 ) (5) ASPECT button ( .
7 Setting up Setting up Install the projector according to the environment and manner the projector will be used in. For the case of installation in a special state such as ceiling mount, the speci ed mounting accessories ( 6SHFL¿FDWLRQV in the User ’s Manual (concise) ) and service may be required.
8 Setting up Arrangement (continued) WARNING (continued on next page) ► Install the projector where you can access the power outlet easily . If an abnormality should occur , unplug the projector urgently . Otherwise it could cause a re or electric shock.
9 Setting up Arrangement (continued) ► 3ODFHWKHSURMHFWRULQDFRROSODFHZLWKVXI¿FLHQW ventilation. The projector may shutdown automatically or may malfunction if its internal temperature is too high. Using a damaged projector could result in a re and an electric shock.
10 Setting up Connecting with your de vices Before connecting the projector to a device, consult the manual of the device to con rm that the device is suitable for connecting with this projector and prepare the required accessories, such as a cable in accord with the signal of the device.
11 Setting up Connecting with your devices (continued) • Before connecting the projector to a computer , consult the computer ’s manual and check the compatibility of the signal level, the synchronization methods and the display resolution output to the projector .
12 Setting up Connecting with your devices (continued) (continued on next page) • If an oversized USB storage device blocks the LAN port, use a USB extension cable to connect the USB storage device. NO TE ► Before connecting the projector to a network system be sure to obtain the consent of the administrator of the network.
13 VCR/DVD/Blu-ray Disc TM player Setting up • The HDMI port of this model is compatible with HDCP (High-band- width Digital Content Protection) and therefore capable of displaying a video signal from HDCP compatible DVD players or the like. - The HDMI supports the following signals.
14 Setting up Connecting with your devices (continued) Monitor Speakers (with an ampli er) CONTROL MONITOR OUT AUDIO OUT AC IN LAN HDMI USB DC5V 0.
15 Connecting to a pow er suppl y 1. Put the connector of the power cord into the AC IN (AC inlet) of the projector . 2. Firmly plug the power cord’s plug into the outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange.
16 Use the supplied adapter cover to prevent the USB wireless adapter from coming off easily . 1. Loosen the screw (marked with triangle) on the bottom right of the USB TYPE A port. 2. Insert the tab of the cover into the hole at the upper left of the USB TYPE A port in the direction of the arrow .
17 30º 3 m 30º (approx.) Remote control About the remote contr ol signal The remote control works with the projector ’s remote sensor . This projector has a remote sensor on the front.
18 Using as a simple PC mouse & k eyboar d The accessory remote control works as a simple mouse and keyboard of the computer , when the projector ’s USB TYPE B port and the computer ’s type A USB port are connected and MOUSE is selected for the USB TYPE B item in the OPTION menu ( 54 ).
19 1. Make sure that the power cord is rmly and correctly connected to the projector and the outlet. T ur ning on the power 2. Make sure that the POWER indicator is steady orange ( 100 ). Then remove the lens cover . 3. Press ST ANDBY/ON button on the projector or the remote control.
20 Po wer on/of f Precaution for lens co ver a ttachment and removal When you attach or remove the lens cover , move it vertically up and down while keeping the knob to the right as illustrated in the gure. ► A strong light is emitted when the projector ’s power is on.
21 Operating 1. Adjusting the v olume Use the VOLUME + / VOLUME - buttons to adjust the volume. A dialog will appear on the screen to aid you in adjusting the volume. If you do not do anything, the dialog will automatically disappear after a few seconds.
22 1. Press INPUT button on the projector . Each time you press the button, the projector switches its input port from the current port as below . Selecting an input signal INPUT button ● While ON i.
23 Operating Selecting an aspect ratio ● ASPECT button does not work when no proper signal is inputted. ● NORMAL mode keeps the original aspect ratio setting. 1. Press SEARCH button on the remote control. The projector will start to check its input ports as below in order to nd any input signals.
24 Operating Adjusting the projector's eleva tor When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally . Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the projector within 12 degrees.
25 Operating 1. Press POSITION button on the remote control when no menu is indicated. The “POSITION” indication will appear on the screen. Adjusting the position 2. Use the ▲ / ▼ / ◄ / ► cursor buttons to adjust the picture position. When you want to reset the operation, press RESET button on the remote control during the operation.
26 Operating 1. Press KEYSTONE button on the remote control. A dialog will appear on the screen to aid you in correcting the distortion. Cor r ecting the k eystone distor tions 2. Use the ▲ / ▼ cursor buttons to select AUTO or MANUAL operation, and press the ► button to perform the following.
27 Operating 1. Using the magnify feature 2. MAGNIFY ON/OFF button VIDEO DOC.CAMERA KEYSTONE ASPECT SEARCH BLANK MUTE MY BUTTON COMPUTER MY SOURCE/ AUTO MAGNIFY PAGE DOWN ON OFF FREEZE UP 㧗 VOLUME 1 2 3. 4. Press the MAGNIFY ON button on the remote control.
28 1. Press BLANK button on the remote control. The BLANK screen will be displayed instead of the screen of input signal. Please refer to BLANK item in SCREEN menu ( 47 ). T o exit from the BLANK screen and return to the input signal screen, press BLANK button again.
29 Operating 1. T o start the MENU, press the MENU button. The MENU you last used (EASY or ADV ANCED) will appear . EASY MENU has priority to appear just after powered on. Using the menu function 2. (1) Use the ▲ / ▼ cursor buttons to select an item to operate.
30 Using the menu function (continued) 3. T o close the MENU, press the MENU button again or select EXIT and press the ◄ cursor button or ENTER button.
31 EASY MENU EASY MENU From the EASY MENU, items shown in the table below can be performed. Select an item using the ▲ / ▼ cursor buttons. Then perform it according to the following table. Item Description ASPECT Using the ◄ / ► buttons switches the mode for aspect ratio.
32 EASY MENU Item Description ECO MODE Using the ◄ / ► buttons swithes the ECO MODE. See the ECO MODE item in SETUP menu ( 44 ). INST ALLA TION Pressing the ► button displays the INST ALLA TION dialog. See the INST ALLA TION item in SETUP menu ( 44 ).
33 PICTURE menu PICTURE menu From the PICTURE menu, items shown in the table below can be performed. Select an item using the ▲ / ▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.
34 PICTURE menu (continued on next page) Item Description COLOR TEMP Using the ▲ / ▼ buttons switches the color temperature mode. T o adjust CUSTOM Selecting a mode whose name includes CUSTOM and then pressing the ► button or the ENTER button displays a dialog to aid you in adjusting the OFFSET and GAIN of the selected mode.
35 PICTURE menu Item Description SHARPNESS Using the ◄ / ► buttons adjusts the sharpness. Weak Ù Strong • There may be some noise and/or the screen may icker for a moment when an adjustment is made. This is not a malfunction. MY MEMOR Y This projector has 4 memories for adjustment data (for all the items of the PICTURE menu).
36 IMAGE menu IMAGE menu From the IMAGE menu, items shown in the table below can be performed. Select an item using the ▲ / ▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.
37 IMAGE menu Item Description V POSITION Using the ◄ / ► buttons adjusts the vertical position. Down Ù Up • Over-adjusting the vertical position may cause noise to appear on the screen. If this occurs, please reset the vertical position to the default setting.
38 IMAGE menu Item Description H PHASE Using the ◄ / ► buttons adjusts the horizontal phase to eliminate icker . Right Ù Left • This item can be selected only for a computer signal or a component video signal. This function is unavailable for a signal from the LAN , USB TYPE A , USB TYPE B or HDMI port.
39 INPUT menu INPUT menu From the INPUT menu, items shown in the table below can be performed. Select an item using the ▲ / ▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.
40 INPUT menu Item Description VIDEO FORMA T The video format for S-VIDEO port and VIDEO port can be set. (1) Use the ▲ / ▼ buttons to select the input port. (2) Using the ◄ / ► buttons switches the mode for video format. AUTO Ù NTSC Ù P AL Ù SECAM N-P AL Ù M-P AL Ù NTSC4.
41 INPUT menu Item Description COMPUTER IN The computer input signal type for COMPUTER IN1 and IN2 ports can be set. (1) Use the ▲ / ▼ buttons to select the COMPUTER IN port to be set. (2) Use the ◄ / ► buttons to select the computer input signal type.
42 INPUT menu Item Description RESOLUTION The resolution for the COMPUTER IN1 and COMPUTER IN2 input signals can be set on this projector . (1) In the INPUT menu select the RESOLUTION using the ▲ / ▼ buttons and press the ► button. The RESOLUTION menu will be displayed.
43 SETUP menu SETUP menu From the SETUP menu, items shown in the table below can be performed. Select an item using the ▲ / ▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.
44 SETUP menu Item Description AUTO ECO MODE Using the ▲ / ▼ buttons turns on/off the AUTO ECO MODE. ON Ù OFF • When ON is selected, the projector will always be set to Eco mode at start-up regardless of the ECO MODE ( below ) setting.
45 Item Description ST ANDBY MODE Using ▲ / ▼ buttons switches the standby mode setting between NORMAL and SA VING. NORMAL Ù SA VING When SA VING is selected, the power consumption in the standby.
46 A UDIO menu AUDIO menu From the AUDIO menu, items shown in the table below can be performed. Select an item using the ▲ / ▼ cursor buttons, and press the ► cursor button or the ENTER button to execute the item. Then perform it according to the following table.
47 SCREEN menu SCREEN menu From the SCREEN menu, items shown in the table below can be performed. Select an item using the ▲ / ▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.
48 SCREEN menu Item Description MyScreen This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and ST ART UP screen. Display the image you want to capture before executing the following procedure. 1.
49 SCREEN menu Item Description MyScreen Lock Using the ▲ / ▼ buttons turns on/off the MyScreen lock function. ON Ù OFF When the ON is selected, the item MyScreen is locked.
50 SCREEN menu Item Description SOURCE NAME Each input port for this projector can have a name applied to it. (1) Use the ▲ / ▼ buttons on the SCREEN menu to select SOURCE NAME and press the ► or ENTER button. The SOURCE NAME menu will be displayed.
51 SCREEN menu Item Description SOURCE NAME ( continued ) (6) The current name will be displayed on the rst line. Use the ▲ / ▼ / ◄ / ► buttons and the ENTER or INPUT button to select and enter characters. T o erase 1 character at one time, press the RESET button or press the ◄ and INPUT button at the same time.
52 SCREEN menu Item Description C.C. (Closed Caption) The C.C. is the function that displays a transcript or dialog of the audio portion of a video, les or other presentation or other relevant sounds. It is required to have NTSC format video or 480i@60 format component video source supporting C.
53 OPTION menu OPTION menu From the OPTION menu, items shown in the table below can be performed. Select an item using the ▲ / ▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME and FIL TER TIME.
54 OPTION menu Item Description AUTO POWER OFF Using the ▲ / ▼ buttons adjusts the time to count down to automatically turn the projector off. Long (max. 99 minutes) Ù Short (min. 0 minute = DISABLE) When the time is set to 0, the projector is not turned off automatically .
55 OPTION menu Item Description LAMP TIME The lamp time is the usage time of the lamp, counted after the last resetting. It is shown in the OPTION menu. Pressing the RESET button on the remote control or the ► button of the projector displays a dialog.
56 OPTION menu Item Description MY BUTT ON This item assigns one of the following functions to the ECO button on the control panel ( 5 ) and MY BUTT ON 1/2 on the remote control ( 6 ). (1) Choose a button to assign a function from ECO, MY BUTT ON-1 and MY BUTT ON-2.
57 OPTION menu Item Description MY BUTT ON ( continued ) • PICTURE MODE: Changes the PICTURE MODE ( 31 ). • FIL TER RESET : Displays the lter time reset con rmation dialogue ( 55 ). • TEMPLA TE: Makes the template pattern selected to the TEMPLA TE item ( 51 ) appear or disappear .
58 OPTION menu Item Description SERVICE (continued) GHOST Adjust the settings using the ▲ / ▼ buttons to eliminate ghosting. FIL TER MESSAGE Use the ▲ / ▼ button to set the timer for notifying.
59 OPTION menu Item Description SERVICE (continued) COMMUNICA TION Selecting this item displays COMMUNICA TION menu. In this menu, you can con gure the serial communication settings of the projector using the CONTROL port. • Select an item using the cursor buttons ▲ / ▼ .
60 OPTION menu Item Description SERVICE (continued) COMMUNICA TION (continued) SERIAL SETTINGS Select the serial communication condition for the CONTROL port.
61 OPTION menu Item Description SERVICE (continued) COMMUNICA TION (continued) RESPONSE LIMIT TIME Select the time period to wait for receiving response data from other device communicating by the NETWORK BRIDGE and the HALF-DUPLEX through the CONTROL port.
62 OPTION menu Item Description SERVICE (continued) INFORMA TION Selecting this item displays a dialog titled “INPUT_INFORMA TION”. It shows the information about the current input. • The “FRAME LOCK” message on the dialog means the frame lock function is working.
63 NETWORK menu Remember that incorrect network settings on this projector may cause trouble on the network. Be sure to consult with your network administrator before connecting to an existing access point on your network. Select “NETWORK” from the main menu to access the following functions.
64 NETWORK menu Item Description WIRELESS SETUP (continued) DHCP (Dynamic Host &RQ¿JXUDWLRQ Protocol) Use the ▲ / ▼ buttons to turn DHCP on/of f. ON Ù OFF Select OFF when the network does not have DHCP enabled. T o save the setting, press the ► button.
65 NETWORK menu Item Description WIRELESS SETUP (continued) DA TE AND TIME Use the ▲ / ▼ / ◄ / ► buttons to enter the Y ear (last two digits), Month, Date, Hour and Minute. • When this item is set, the same item in the WIRED SETUP menu is overwritten with the same setting ( 69 ).
66 NETWORK menu Item Description WIRELESS SETUP (continued) SSID Use the ▲ / ▼ buttons to select the SSID to display the SSID menu. #1 DEF AUL T Ù #2 DEF AUL T Ù #3 DEF AUL T #5 CUSTOM Ù #4 DEF AUL T Select one of the DEF AUL T (#1~#4) and press ► or ENTER button.
67 NETWORK menu Item Description WIRELESS INFORMA TION "Selecting this item displays the WIRELESS_INFORMA TION dialog for viewing the wireless LAN settings." Use the ▲ / ▼ buttons to switch the page. The rst page shows the wireless LAN settings.
68 NETWORK menu Item Description WIRED SETUP Selecting this item displays the WIRED SETUP menu for the wired LAN. Use the ▲ / ▼ buttons to select an item, and the ► or ENTER button on the remote control to perform the item. DHCP (Dynamic Host &RQ¿JXUDWLRQ Protocol) Use the ▲ / ▼ buttons to turn DHCP on/of f.
69 NETWORK menu Item Description WIRED SETUP (continued) TIME DIFFERENCE Use the ▲ / ▼ buttons to enter the TIME DIFFERENCE. Set the same TIME DIFFERENCE as the one set on your computer . If unsure, consult your IT manager . Use the ► button to return to the menu after setting the TIME DIFFERENCE.
70 NETWORK menu Item Description PROJECTOR NAME (1) Use the ▲ / ▼ buttons on the NETWORK menu to select the PROJECTOR NAME and press the ► button. The PROJECT OR NAME dialog will be displayed. (2) The current PROJECTOR NAME will be displayed on the rst 3 lines.
71 NETWORK menu Item Description MY IMAGE Selecting this item displays the MY IMAGE menu. Use the application to transfer the im- age data. It can be downloaded from the Hitachi web site.
72 NETWORK menu Item Description PRESENT A TION Selecting this item displays the PRESENT A TION menu. Use ▲ / ▼ buttons to select one of the following items, then press ► or ENTER button to use the function. • T o use Network Presentation, an exclusive application, "LiveViewer" is required.
73 SECURITY menu Item Description PRESENT A TION (continued) MUL TI PC MODE (continued) • T o change from Single PC mode to Multi PC mode, press ► button to choose OK in the dialog and press the ENTER or INPUT button.
74 SECURITY menu This projector is equipped with security functions. From the SECURITY menu, items shown in the table below can be performed. T o use SECURITY menu: User registration is required before using the security functions. Enter to the SECURITY menu 1.
75 SECURITY menu Item Description MyScreen P ASSWORD The MyScreen P ASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten.
76 SECURITY menu Item Description PIN LOCK PIN LOCK is a function which prevents the projector from being used unless a registered Code is input. 1 T urning on the PIN LOCK 1-1 Use the ▲ / ▼ buttons on the SECURITY menu to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/off menu.
77 SECURITY menu Item Description TRANSITION DETECTOR If this function is set to ON and the vertical angle of the projector or the INST ALLA TION setting is different from the previous recorded setting, the TRANSITION DETECTOR ON alarm will be displayed and the input signal will not be displayed.
78 SECURITY menu Item Description MY TEXT P ASSWORD The MY TEXT P ASSWORD function can prevent the MY TEXT from being overwritten. When the password is set for the MY TEXT ; • The MY TEXT DISPLA Y menu will be unavailable, which can prohibit changing the DISPLA Y setting.
79 SECURITY menu Item Description MY TEXT DISPLA Y (1) Use the ▲ / ▼ buttons on the SECURITY menu to select the MY TEXT DISPLA Y and press the ► or ENTER button to display the MY TEXT DISPLA Y on/off menu. (2) Use the ▲ / ▼ buttons on the MY TEXT DISPLA Y on/off menu to select on or off.
80 Presentation tools Presentation tools The PC-LESS Presentation reads image and audio data from the storage media inserted into the USB TYPE A port and displays the image in the following modes. The PC-LESS Presentation can be started by selecting the USB TYPE A port as the input source.
81 Presentation tools • Files with a resolution larger than the following are not supported. CPX10WN, CPX1 1WN : 1024 x 768 CPWX12WN: 1280 x 800 (* Some computers may not support 1280 x 800.) • Files with a resolution smaller than 36x36 are not supported.
82 Presentation tools PC-LESS Presentation (continued) The SETUP menu for the selected image Item Functions SETUP Use the ◄ / ► cursor buttons to switch each setting or use the ► cursor button to execute the functions as follows. RETURN Press the ► cursor button or ENTER to return to the Thumbnail screen.
83 Presentation tools Y ou can also control the images by using the menu on the Thumbnail screen. PC-LESS Presentation (continued) Operating by the menu on the Thumbnail screen Item Functions Moves to an upper folder . SORT Allows you to sort les and folders as following.
84 Presentation tools PC-LESS Presentation (continued) • These operations are not accessible while the projector OSD is displayed. • The Thumbnail mode is able to display up to 20 les in one page. • It is not possible to change the input port by using the INPUT button when the Thumbnail screen, Slideshow , or Full Screen is displayed.
85 Presentation tools PC-LESS Presentation (continued) The Full Screen mode shows a full display image. T o display in Full Screen mode, select an image in the Thumbnail screen. Then press the ENTER button on the remote control, the INPUT button on the control panel or click [ ENTER] on the Web Remote Control.
86 Presentation tools PC-LESS Presentation (continued) Slideshow Mode While the Slideshow is displayed, the following button operations are enabled when still images are displayed, and the same button operations in the Full Screen mode are enabled when movies are displayed.
87 Presentation tools PC-LESS Presentation (continued) Y ou can play the Slideshow at your desired con guration. Con gure the Slideshow items in the Thumbnail. 1) RETURN : Returns to the thumbnail mode. 2) PLA Y : Play the Slideshow . 3) ST ART : Set the beginning number of the Slideshow .
88 Presentation tools PC-LESS Presentation (continued) Playlist The Playlist is a DOS format text le, which decides the order of displayed still image les in the Thumbnail or Slideshow . The playlist le name is “playlist.txt” and it can be edited on a computer .
89 Presentation tools USB Display The projector can display images transferred from a computer via an USB cable ( 11 ). Select the USB DISPLA Y for the USB TYPE B item in the OPTION menu.
90 Presentation tools This application will appear in the Windows noti cation area once it starts. Y ou can quit the application from your computer by selecting “Quit” on the menu. • The “LiveViewer” (refer to the Network Guide ) and this application cannot be used at the same time.
91 Presentation tools Display : The Floating menu is displayed, and the icon disappears from the Windows noti cation area. Quit : The application is closed, and the icon disappears from the Windows noti cation area. The menu shown in the right will be displayed when you right-click the application icon in the Windows noti cation area.
92 Presentation tools If you select the Option button on the Floating menu, the Options window is displayed. Optimize P erfor mance The “LiveViewer Lite for USB” captures screenshots in JPEG data and sends them to the projector . The “LiveV iewer Lite for USB” has two options that have different compression rate of JPEG data.
93 Maintenance Maintenance A lamp has nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor . Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
94 Maintenance Lamp war ning Replacing the lamp (continued) HIGH VOL T AGE HIGH TEMPERA TURE HIGH PRESSURE ► The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.
95 Maintenance (continued on next page) The air lter unit of this projector consists of a lter cover , two kinds of lters, and a lter frame. The new double large lters system is expected to function longer . However , please check and clean it periodically to keep ventilation needed for normal operation of the projector .
96 Maintenance Cleaning and replacing the air lter (continued) 9. T urn the projector on and reset the lter time using the FIL TER TIME item in the EASY MENU. ► Before taking care of the air lter , make sure the power cable is not plugged in, then allow the projector to cool suf ciently .
97 Maintenance Other care In order to ensure the safe use of your projector , please have it cleaned and inspected by your dealer about once every year . 1. T urn the projector off, and unplug the power cord. Allow the projector to cool suf ciently .
98 T r oubleshooting T roubleshooting If an abnormal operation should occur , stop using the projector immediately . Otherwise if a problem occurs with the projector , the following checks and measures are recommended before requesting repair . If this does not resolve the problem, please contact your dealer or service company .
99 Message Description The internal temperature is rising. Please turn the power off, and allow the projector to cool down at least 20 minutes. After having con rmed the following items, please turn the power ON again.
100 T r oubleshooting R e gar ding the indicator lamps When operation of the LAMP , TEMP and POWER indicators differs from usual, check and cope with it according to the following table. POWER indicator LAMP indicator TEMP indicator Description Lighting In Orange T urned off T urned off The projector is in a standby state.
101 T r oubleshooting Regarding the indicator lamps (continued) • When the interior portion has become overheated, for safety purposes, the projector is automatically shut down, and the indicator lamps may also be turned off. In such a case, disconnect the power cord, and wait at least 45 minutes.
102 R esetting all settings When it is hard to correct some wrong settings, the F ACTOR Y RESET function of SERVICE item in OPTION menu ( 62 ) can reset all settings (except settings such as LANGUAGE, LAMP TIME, FIL TER TIME, FIL TER MESSAGE, SECURITY and NETWORK) to the factory default.
103 T r oubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect Reference page Sound does not come out. The signal cables are not correctly connected. Correctly connect the audio cables.
104 Phenomenon Cases not involving a machine defect Reference page No pictures are displayed. (continued) The projector does not recognize the USB storage device inserted into USB TYPE A port. Use the REMOVE USB function rst, remove the USB storage device, and then insert it into the port again.
105 Phenomenon Cases not involving a machine defect Reference page Some kind of image degradation such as ickering or stripes appear on screen. When the projector is operating in Eco mode, ÀLFNHULQJPDDSSHDURQVFUHHQ Set ECO MODE to NORMAL, and set AUTO ECO MODE to OFF , in the SETUP menu.
106 • Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and it does not constitute or imply a machine defect. NO TE Phenomenon Cases not involving a machine defect Reference page Schedule function does not work The SA VING function is working.
107 Speci fi cations Speci cations Please see the 6SHFL¿FDWLRQV in the User ’s Manual (concise) which is a book. End User License Agr eement for the Projector Software • Software in the proj.
1 Projector CPX10WN/CPX11WN/ CPWX12WN User's Manual (detailed) Network Guide Thank you for purchasing this product. This manual is intended to explain only the network function. For proper use of this product, please refer to this manual and the other manuals for this product.
2 Contents Contents Caution .......................................................................................... 4 1. Connection to the network ...................................................... 5 1.1 System requirements ................
3 Contents 6. Network Bridge Function ....................................................... 52 6.1 Connecting devices .................................................................................. 52 6.2 Communication setup .................
4 Caution Caution To use the wireless network function of this projector, the designated USB wire- less adapter that is sold as an option is required. For precautions according to the standards and laws, refer to the documents that come with the adapter.
5 1. Connection to the network 1.1 System requir ements 1. Connection to the network The following equipments are required to connect the projector to your computer through the network.
6 1. Connection to the network 1.1 System requirements (continued) • The network communication control is disabled while the projector is in standby mode if the ST ANDBY MODE item is set to SA VING. Please connect the network communication to the projector after setting the ST ANDBY MODE to NORMAL.
7 1. Connection to the network 1.3 Manual network connection setting - W ired LAN - This section explains how to set it up manually . 1.3.1 Equipments connection Connect the projector and a computer with a LAN cable. * Before connecting with an existing network, contact the network administrator .
8 1. Connection to the network 1.3 Manual network connection setting - Wired LAN - (continued) 7) Select "Use the following IP address" and con gure the IP address, Subnet mask and Default gateway for the computer accordingly .
9 1. Connection to the network 1.3 Manual network connection setting - Wired LAN - (continued) [About IP address] Ŷ6HWWLQJPDQXDOO The Network address portion of the IP address setting on your computer must be the same as the setting on the projector .
10 1. Connection to the network 1.3 Manual network connection setting - Wired LAN - (continued) 2) Click “Connections” tab and then click [LAN settings] button to open “Local Area Network (LAN) Settings”.
11 1. Connection to the network 1.4 Manual network connection setting - W ir eless LAN - Using the designated USB wireless adapter (option) on the projector enables the projector and computer to communicate in both the Ad-Hoc and Infrastructure modes.
12 1. Connection to the network 1.4.2 W ireless LAN connection set up Using wireless LAN utility for Windows ® 7 standard. Wireless LAN initial settings for the projector is as follows.
13 1. Connection to the network 1.4 Manual network connection setting - Wireless LAN - (continued) 4) Select "Use the following IP address" and con gure the IP address, Subnet mask and Default gateway for the computer accordingly . After setting is complete, click [OK] to close the window .
14 1. Connection to the network 1.4 Manual network connection setting - Wireless LAN - (continued) 6) From the connectable wireless networks, select the SSID of the projector (set to "wireless" by default), and click [Connect]. If you have enabled encryption, a window asking for input of the encryption key will be displayed.
15 2. Network Pr esentation The projector can display or play back the computer screen images and audio data that are transmitted through the network. This Network Presentation feature helps you to smoothly make your presentations and conduct conferences.
16 Y ou can adjust or control the projector via a network from a web browser on a computer that is connected to the same network. • Internet Explorer ® 6.0 or later is required. • If JavaScript ® is disabled in your web browser con guration, you must enable JavaScript ® in order to use the projector web pages properly .
17 3. We b Control 3.1.1 Logon T o use the Projector Web Control function, you need to logon with your user name and password. • The language used on the Projector W eb Control screen is the same as that of the OSD on the projector . If you want to change it, you need to change the OSD language on the projector .
18 3.1.2 Network Infor mation Displays the projector ’s current network con guration settings. Item 'HVFULSWLRQ Common Information Displays information common to both wireless and wired LAN. Projector Name Displays the projector name settings.
19 3.1.3 Network Settings Displays and con gures network settings. Item 'HVFULSWLRQ Common Setup Displays information common to both wireless and wired LAN. Projector Name Con gures the name of the projector . The length of the Projector Name can be up to 64 alphanumeric characters.
20 3.1 Projector Web Control - Network Settings (continued) 3. We b Control Item 'HVFULSWLRQ Wireless Setup Con gures the wireless LAN settings. Mode Select " AD-HOC" or " Infrastructure". ,3&RQ¿JXUDWLRQ Con gures network settings.
21 Click the [Apply] button to save the settings. 3.1 Projector Web Control - Network Settings (continued) Item 'HVFULSWLRQ Wired Setup Con gures the wired LAN settings. ,3&RQ¿JXUDWLRQ Con gures network settings. '+&321 Enables DHCP .
22 3.1.4 Port Settings Displays and con gures communication port settings. Item 'HVFULSWLRQ Network Control Port1 (Port:23) Con gures command control port 1 (Port:23). Port open Click the [Enable] check box to use port 23. Authentication Click the [Enable] check box when authentication is required for this port.
23 Item 'HVFULSWLRQ SNMP Port Con gures the SNMP port. Port open Click the [Enable] check box to use SNMP . T rap address Con gures the destination of the SNMP T rap in IP format. • The address allows not only IP address but also domain name if the valid DNS server is setup in the Network Settings .
24 3.1.5 Mail Settings Displays and con gures e-mail addressing settings. Item 'HVFULSWLRQ Send Mail Click the [Enable] check box to use the e-mail function. Con gure the conditions for sending e-mail under the Alert Settings . SMTP Server Address Con gures the address of the mail server in IP format.
25 3.1.6 Aler t Settings Displays and con gures failure & alert settings. Item 'HVFULSWLRQ Cover Error The lamp cover has not been properly xed. Fan Error The cooling fan is not operating. Lamp Error The lamp does not light, and there is a possibility that interior portion has become heated.
26 The Alert Items are shown below . Item 'HVFULSWLRQ Alarm Time Con gures the time to alert. (Only Lamp Time Alarm and Filter Time Alarm .) SNMP T rap Click the [Enable] check box to enable SNMP T rap alerts. Send Mail Click the [Enable] check box to enable e-mail alerts.
27 3.1.7 Schedule Settings Displays and con gures schedule settings. Item 'HVFULSWLRQ 'DLO Con gures the daily schedule. Sunday Con gures the Sunday schedule. Monday Con gures the Monday schedule. T uesday Con gures the T uesday schedule.
28 3.1 Projector Web Control - Schedule Settings (continued) The schedule settings are shown below . Item 'HVFULSWLRQ Schedule Click the [Enable] check box to enable the schedule. 'DWH0RQWK'D Con gures the month and date.
29 • After the projector is moved, check the date and time set for the projector before con guring the schedules. • The internal clock’ s time may not remain accurate.
30 3.1.8 Date/Time Settings Displays and con gures the date and time settings. Item 'HVFULSWLRQ &XUUHQW'DWH Con gures the current date in year/month/day format. Current Time Con gures the current time in hour:minute:second format.
31 Item 'HVFULSWLRQ Time difference Con gures the time difference. Set the same time dif ference as the one set on your computer . If unsure, consult your IT manager . SNTP Click the [ON] check box to retrieve Date and T ime information from the SNTP server and set the following items.
32 3.1.9 Security Settings Displays and con gures passwords and other security settings. Item 'HVFULSWLRQ User Account Con gures the user name and password. User name Con gures the user name. The length of the text can be up to 32 alphanumeric characters.
33 3.1.10 Projector Contr ol Item 'HVFULSWLRQ MAIN POWER T urns the power on/off. INPUT SOURCE Selects the input source. 3,&785(02'( Selects the picture mode setting. BLANK ON/OFF T urns Blank on/off. MUTE T urns Mute on/off. FREEZE T urns Freeze on/off.
34 3.1 Projector Web Control - Projector Control (continued) Item 'HVFULSWLRQ PICTURE BRIGHTNESS Adjusts the brightness setting. CONTRAST Adjusts the contrast setting. GAMMA Selects the gamma setting. COLOR TEMP Selects the color temperature setting.
35 3.1 Projector Web Control - Projector Control (continued) Item 'HVFULSWLRQ SETUP AUTO KEYST ONE EXECUTE Performs the automatic keystone distortion setting. KEYSTONE V Adjusts the vertical keystone distortion setting. $872(&202'( T urns on/off the automatic eco mode function.
36 3.1 Projector Web Control - Projector Control (continued) 3. We b Control Item 'HVFULSWLRQ $8',2 VOLUME Adjusts the volume setting. SPEAKER T urns the built-in speaker on/off. $8',26285&( COMPUTER IN1 Assigns the AUDIO SOURCE - COMPUTER IN1 input port.
37 Item 'HVFULSWLRQ OPTION AUTO SEARCH T urns the automatic signal search function on/off. AUTO KEYST ONE T urns the automatic keystone distortion correction function on/off. ',5(&732:(521 T urns the direct power on function on/off.
38 The items shown in the table below can be performed using the Projector Control menu. Click the [Quit Presenter Mode] . Item 'HVFULSWLRQ SERVICE Quit Presenter Mode Quit compulsorily from the Presenter mode. 3.1 Projector Web Control - Projector Control (continued) 3.
39 3.1.11 Remote Control Y ou can use your Web browser to control the projector . The functions on the bundled remote control are assigned to the Web Remote Control screen. • Do not attempt to control the projector with the projector ’s remote control and via your W eb browser at the same time.
40 3.1.12 Projector Status Displays the settings and status of the projector . Item 'HVFULSWLRQ Error Status Displays the current error status Lamp Time Displays the usage time for the current lamp. Filter Time Displays the usage time for the current lter .
41 3.1.13 Network Restar t Restarts the projector ’s network connection. Item 'HVFULSWLRQ Restart Restarts the projector ’s network connection in order to activate new con guration settings. • Restarting requires you to re-log on in order to further control or con gure the projector via a web browser .
42 3. We b Control The Main window as shown above is displayed at rst. However , if you have enabled User Password on the T ools window ( 46 ), a dialog prompting you to enter the password as shown on the right will be displayed, and no operation is enabled until you have entered the password.
43 3. We b Control 3.2 Crestron e-Control ® (continued) 3.2.1 Main window Y ou can operate the basic controls of the projector on this screen. • If the projector is in the standby mode, only the Power button can be operated. NO TE 1 Click a button and operate as follows.
44 3. We b Control 3.2 Crestron e-Control ® - Main window (continued) 3 Click a button and operate as follows. T o show the hidden buttons, click the ◄ / ► icons at the left and right ends. Button 'HVFULSWLRQ Freeze T urns Freeze on/off. Contrast Adjusts the contrast setting.
45 3. We b Control 3.2 Crestron e-Control ® (continued) 3.2.2 T ools window Con gures the settings between the projector and Crestron ® control system. Click the [Exit] button to return to the Main window . 1 Crestron Control Con gures the settings of Crestron ® control system devices.
46 3. We b Control 3.2 Crestron e-Control ® - T ools window (continued) 3 Projector (continued) Con gures the network settings of the projector . Item 'HVFULSWLRQ '+&3 Enables DHCP . IP Address Con gures the IP address when DHCP is disabled.
47 3. We b Control 3.2 Crestron e-Control ® (continued) 3.2.3 Info windo w Displays the settings and status of the projector . Click the [Exit] button to return to the Main window . 1 Projector Information Item 'HVFULSWLRQ Projector Name Displays the projector name settings.
48 3. We b Control 3.2 Crestron e-Control ® (continued) 3.2.4 Help Desk window Sends/receives messages to/from the administrator for Crestron RoomView® Express.
49 3. We b Control 3.2 Crestron e-Control ® (continued) 3.2.5 Emergency Aler t When the administrator for Crestron RoomView ® Express sends out an alert message, it will be displayed on the screen. Y ou can reply to the alert message via a chat format.
50 1 4 3 2 4. My Image Function The projector can display still images that are transferred via the network. • It is possible to allocate the image le up to 4 in the maximum. • Using MY BUTT ON that registered MY IMAGE can display transferred image.
51 1 4 3 2 12 5. Messenger Function The projector can display text data transferred via the network on the screen and play back audio data inside the projector .
52 6. Network Bridge Function This projector is equipped with the NETWORK BRIDGE function to perform mutual conversion of a network protocol and a serial interface.
53 6. Network Bridge Function 6.2 Communication setup 6.3 Communication por t 1) In the COMMUNICA TION TYPE menu, select NETWORK BRIDGE (WIRELESS or WIRED depending on the type of connection you use) for the CONTROL port.
54 6.4 T r ansmission method 6.4.1 HALF-DUPLEX The transmission method can be selected from the menus, only when the NETWORK BRIDGE is selected for the COMMUNICA TION TYPE.
55 • With using the HALF-DUPLEX method, the projector can send out 254 byte data as maximum at once. • If it is not required to monitor the response data from an external device and the RESPONSE LIMIT TIME is set to OFF , the projector can receive the data from the computer and send it out to an external device continuously .
56 7. Other Functions 7.1 E-mail Aler ts The projector can automatically send an alert message to the speci ed e-mail addresses when the projector detects a certain condition that is requiring maintenance or detected an error . • Up to ve e-mail addresses can be speci ed.
57 7.1 E-mail Alerts (continued) 7. Other Functions 5) Click the [Alert Settings] on the main menu to con gure the E-mail Alerts settings. 6) Select and con gure each alert item. Refer to item 3.1.6 Alert Settings ( 31 ) for further information.
58 7.2 Projector Mana gement using SNMP The SNMP (Simple Network Management Protocol) enables to manage the projector information, which is a failure or warning status, from the computer on the network. The SNMP management software will be required on the computer to use this function.
59 7.3 Ev ent Scheduling The scheduling function enables to setup scheduled events including power on / power off. It enables to be “self-management” projector . • Y ou can schedule the following control events: Power , Input Source, My Image, Messenger , Slideshow .
60 • In standby mode, the POWER indicator will ash green for approx. 3 seconds when at least 1 “Power ON” schedule is saved. • When the schedule function is used, the power cord must be connected to the projector and the outlet. The schedule function does not work when the breaker in a room is tripped.
61 7.3 Event Scheduling(continued) Date/Time Settings ( 30 ) • The internal clock’ s time may not remain accurate. Using SNTP is recommended to maintain accurate time ( 31 ). • Once you turn off the projector in the SA VING mode ( SETUP menu in the Operating Guide ) or the AC power , the current date and time setting is reset.
62 7.4 Command Control via the Networ k Y ou can con gure and control the projector via the network using RS-232C commands. Communication P or t The following two ports are assigned for the command control. Command Control Settings ( 22 ) 4) Click the [Enable] check box to open Network Control Port1 (Port: 23) to use TCP #23.
63 7.4 Command Control via the Network (continued) When the authentication setting is enabled, the following settings are required. ( 32 ) 7) Click the [Security Settings] on the main menu. 8) Click the [Network Control] and enter the desired authentication password.
64 Command F or mat Command formats differ among the dif ferent communication ports. ● TCP #23 Y ou can use the RS-232C commands without any changes.
65 Reply Data f or mat The connection ID (the data is same as the connection ID data on the sending data format) is attached to the RS-232C commands reply data.
66 Automa tic Connection Break The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established. The projector does not accept commands without authentication success when authentication is enabled.
67 7. Other Functions 7.5 Crestr on RoomView ® Crestron RoomView ® is a multi-user resource management program provided by Crestron Electronics, Inc. It is an application for managing and controlling the projector and other A V devices collectively .
68 8. T roubleshooting 8. T r oubleshooting Problem Likely Cause Things to Check Reference Page Number Can't communicate Weak radio signal • Bring the computer and projector closer together . • Radio waves won’t go through concrete and metal (steel doors, etc.
69 Item Specifications Control software Dedicated computer application and Web browser Corresponding protocol TCP/IP , DHCP client and HTTP server Network Wireless LAN (IEEE802.
70 10. Warr anty and after-sales ser vice 10. W arranty and after-sales service If a problem occurs with the equipment, please read 8. T roubleshooting ( 68 ) section rst and review all suggested check points. After that, please contact your dealer or service company , if you still have the problem.
1 Resolution (H x V) H. frequency (kHz) V . frequency (Hz) Rating Signal mode 720 x 400 37.9 85.0 VESA TEXT 640 x 480 31.5 59.9 VESA VGA (60Hz) 640 x 480 37.9 72.8 VESA VGA (72Hz) 640 x 480 37.5 75.0 VESA VGA (75Hz) 640 x 480 43.3 85.0 VESA VGA (85Hz) 800 x 600 35.
2 Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some PC models may be different.
3 Connection to the por ts Connection to the ports NO TICE ► Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed. CONTROL MONITOR OUT AUDIO OUT AC IN LAN HDMI USB DC5V 0.
4 D S-VIDEO Mini DIN 4pin jack • System: NTSC, P AL, SECAM, P AL-M, P AL-N, NTSC4.43, P AL (60Hz) Pin Signal 1 Color signal 0.286Vp-p (NTSC, burst), 75 Ω terminator Color signal 0.300Vp-p (P AL/SECAM, burst) 75 Ω terminator 2 Brightness signal, 1.
5 CONTROL MONITOR OUT AUDIO OUT AC IN LAN HDMI USB DC5V 0.5A TYPE A USB TYPE B COMPUTER IN1 COMPUTER IN2 S-VIDEO VIDEO AUDIO IN2 AUDIO IN1 Connection to the por ts (continued) G AUDIO IN1, H AUDIO IN2 Ø3.5 stereo mini jack • 200 mV rms 47k Ω terminator I AUDIO OUT Ø3.
6 Connection to the por ts (continued) J CONTROL D-sub 9pin plug • About the details of RS-232C communication, please refer to the next chapter . Pin Signal Pin Signal Pin Signal 1 (No connection) 4.
7 CONTROL MONITOR OUT AUDIO OUT AC IN LAN HDMI USB DC5V 0.5A TYPE A USB TYPE B COMPUTER IN1 COMPUTER IN2 S-VIDEO VIDEO AUDIO IN2 AUDIO IN1 Y C B /P B C R /P R COMPONENT VIDEO OUT T o input component video signal to COMPUTER IN ports ex.
8 RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer . For details of RS-232C commands, refer to RS-232C Communication / Network command table ( 17 ).
9 RS-232C Communication (continued) Communication settings 1. Protocol 19200bps,8N1 2. Command for mat ("h" shows hexadecimal) Byte Number 01 2 3 4 5 6 789 1 0 1 1 1 2 Command Action Header .
10 RS-232C Communication (continued) 3. R esponse code / Er r or code ("h" shows hexadecimal) (1) ACK reply : 06h When the projector receives the Set, Increment, Decrement or Execute command correctly , the projector changes the setting data for the speci ed item by [T ype], and it returns the code.
11 When the projector connects network, the projector can be controlled with RS- 232C commands from the computer with web browser . For details of RS-232C commands, refer to RS-232C Communication / Network command table ( 17 ). Command Control via the Networ k Connection 1.
12 Communication P or t The following two ports are assigned for the command control. TCP #23 TCP #9715 Con gure the following items form a web browser when command control is used. Port Settings Network Control Port1 (Port: 23) Port open Click the [Enable] check box to open [Network Control Port1 (Port: 23)] to use TCP #23.
13 Command Control via the Networ k (continued) Command control settings [TCP #23] 1. Command for mat Same as RS-232C communication, refer to RS-232C Communicaton command format. 2. R esponse code / Er r or code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the same as RS-232C Communication (1)~(4).
14 2. R esponse code / Er r or code ("h" shows hexadecimal) The connection ID is attached for the TCP#23's response / error codes are used.
15 This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by wired or wireles LAN communicaton, an external device that is connected with this projector by RS- 232C communication can be controlled from the computer as a network terminal.
16 Communication settings For communication setting, use the OPTION - SERVICE - COMMUNICA TION menu. ( OPTION menu - SERVICE - COMMUNICA TION in the Operating Guide ) Item Condition BAUD RA TE 480.
17 Names Operation T ype Header Command Data CRC Action T ype Setting Code Power Set Turn of f BE EF 03 06 00 2A D3 01 00 00 60 00 00 Turn on BE EF 03 06 00 BA D2 01 00 00 60 01 00 Get BE EF 03 06 00 .
18 Names Operation T ype Header Command Data CRC Action Type Setting Code GAMMA Set DEF AUL T-1 BE EF 03 06 00 07 E9 01 00 A1 30 20 00 CUSTOM-1 BE EF 03 06 00 07 FD 01 00 A1 30 10 00 DEF AUL T-2 BE EF.
19 Names Operation T ype Header Command Data CRC Action Type Setting Code User Gamma Point 8 Get BE EF 03 06 00 7C FF 02 00 97 30 00 00 Increment BE EF 03 06 00 1A FF 04 00 97 30 00 00 Decrement BE EF.
20 Names Operation T ype Header Command Data CRC Action Type Setting Code COLOR Get BE EF 03 06 00 B5 72 02 00 02 22 00 00 Increment BE EF 03 06 00 D3 72 04 00 02 22 00 00 Decrement BE EF 03 06 00 02 .
21 Names Operation T ype Header Command Data CRC Action Type Setting Code H SIZE Get BE EF 03 06 00 B5 82 02 00 02 21 00 00 Increment BE EF 03 06 00 D3 82 04 00 02 21 00 00 Decrement BE EF 03 06 00 02.
22 Names Operation T ype Header Command Data CRC Action Type Setting Code COMPUTER IN2 Set AUTO BE EF 03 06 00 32 D7 01 00 1 1 20 03 00 SYNC ON G OFF BE EF 03 06 00 A2 D6 01 00 1 1 20 02 00 Get BE EF .
23 Names Operation T ype Header Command Data CRC Action Type Setting Code MONITOR OUT - HDMI Set COMPUTER IN1 BE EF 03 06 00 7A F4 01 00 B3 20 00 00 COMPUTER IN2 BE EF 03 06 00 BA F6 01 00 B3 20 04 00.
24 Names Operation T ype Header Command Data CRC Action Type Setting Code MUTE Set OFF BE EF 03 06 00 46 D3 01 00 02 20 00 00 ON BE EF 03 06 00 D6 D2 01 00 02 20 01 00 Get BE EF 03 06 00 75 D3 02 00 0.
25 Names Operation T ype Header Command Data CRC Action Type Setting Code USB TYPE B SOUND ENABLE Set Disable BE EF 03 06 00 32 F0 01 00 A5 20 00 00 Enable BE EF 03 06 00 A2 F1 01 00 A5 20 01 00 Get B.
26 Names Operation T ype Header Command Data CRC Action Type Setting Code MENU POSITION V Get BE EF 03 06 00 40 D7 02 00 16 30 00 00 Increment BE EF 03 06 00 26 D7 04 00 16 30 00 00 Decrement BE EF 03.
27 Names Operation T ype Header Command Data CRC Action Type Setting Code AUTO SEARCH Set OFF BE EF 03 06 00 B6 D6 01 00 16 20 00 00 ON BE EF 03 06 00 26 D7 01 00 16 20 01 00 Get BE EF 03 06 00 85 D6 .
28 Names Operation T ype Header Command Data CRC Action Type Setting Code MY BUTTON-2 Set COMPUTER IN1 BE EF 03 06 00 C6 32 01 00 01 36 00 00 COMPUTER IN2 BE EF 03 06 00 06 30 01 00 01 36 04 00 HDMI B.
29 Names Operation T ype Header Command Data CRC Action Type Setting Code MY SOURCE Set COMPUTER IN1 BE EF 03 06 00 F A 38 01 00 20 36 00 00 COMPUTER IN2 BE EF 03 06 00 3A 3A 01 00 20 36 04 00 HDMI BE.
30 PJLink command PJLink command POWR Power Contorol 0 = Standby 1 = Power On POWR ? Power Status inquiry 0 = Standby 1 = Power On 2 = Cool Down INPT Input Source selection 1 1 = COMPUTER IN 1 12 = CO.
31 PJLink command (continued) Commands Control Description Parameter or Response ERST ? Error Status inquiry 1st byte: Refers to Fan error; one of 0 to 2 2nd byte : Refers to Lamp error; one of 0 to 2.
1 ENGLISH Projector CPX10WN/CPX11WN/ CPWX12WN User's Manual (concise) Thank you for purchasing this projector . Please read through this manual before using this product, in order to use safely and utilize well the product. WARNING ► Before using this product, be sure to read all manuals for this product.
2 Fir st of all Entries and gr aphical symbols explanation The following entries and graphical symbols are used for the manuals and the product as follows, for safety purpose. Please know their meanings beforehand, and heed them. Impor tant safety instr uction The followings are important instructions for safely using the product.
3 ENGLISH R e gulator y notices About Electro-Ma gnetic Interference In CANADA This Class B digital apparatus complies with Canadian ICES-003. In the US, and other places where the FCC regulations are applicable Declaration of Conformity T rade name HIT ACHI Model Number CPX10WN, CPX1 1WN, CPWX12WN Responsible Party Hitachi America, Ltd.
4 Contents of package Y our projector should come with the items shown below . Check that all the items are included. Require of your dealer immediately if any items are missing.
5 ENGLISH Preparing for the remote contr ol Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place.
6 WARNING ► Install the projector where you can access the power outlet easily. ► Install the projector in a stable horizontal position. • Do not use any mounting accessories except the accessories speci ed by the manufacturer. Read and keep the manuals of the accessories used.
7 ENGLISH Connecting with your de vices Before connecting the projector to a device, consult the manual of the device to con rm that the device is suitable for connecting with this projector and prepare the required accessories, such as a cable in accord with the signal of the device.
8 Connecting pow er suppl y 1. Put the connector of the power cord into the AC IN (AC inlet) of the projector . 2. Firmly plug the power cord’s plug into the outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange.
9 ENGLISH T ur ning on the pow er 1. Make sure that the power cord is rmly and correctly connected to the projector and the outlet. 2. Make sure that the POWER indicator is steady orange. Then remove the lens cover . 3. Press the ST ANDBY/ON button on the projector or the remote control.
10 Adjusting the projector's eleva tor When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally . Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front side of the projector within 12 degrees.
11 ENGLISH Displaying the picture 1. Activate your signal source. T urn the signal source on, and make it send the signal to the projector . 2. Press the INPUT button on the projector . Each time you press the button, the projector switches its input port in turn.
12 T ur ning of f the pow er 1. Press the ST ANDBY/ON button on the projector or the remote control. The message “Power off?” will appear on the screen for about 5 seconds. 2. Press the ST ANDBY/ON button again while the message appears. The projector lamp will go off, and the POWER indicator will begin blinking in orange.
13 ENGLISH R eplacing the lamp A lamp has nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor . Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
14 HIGH VOL T AGE HIGH TEMPERA TURE HIGH PRESSURE WARNING ► The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
15 ENGLISH Please check and clean the air lter periodically . When the indicators or a message prompts you to clean the air lter , comply with it as soon as possible. The air lter has two kinds of lters inside. Replace the lters when they are damaged or too soiled.
16 NO TE • The information in the CD-ROM is subject to change without notice. Please check our website where you may nd the latest information for this projector . ( 18 ) • No responsibility is taken for any obstacle and defect to hardware and software of your computer as a result of the use of the CD-ROM.
17 ENGLISH Item 6SHFL¿FDWLRQ Product name Liquid crystal projector Liquid Crystal Panel CPX10WN, CPX1 1WN: 786,432 pixels (1024 horizontal x 768 vertical) CPWX12WN: 1,024,000 pixels (1280 horizontal x 800 vertical) Lamp 215 W UHP Speaker 1 W Power supply/ Rated current AC 100-120 V : 3.
18 T roubleshooting - War ranty and after-ser vice If an abnormal operation (such as smoke, strange odor or excessive sound) should occur , stop using the projector immediately .
1 9 ENGLISH T- 1 CPX10WN, CPX1 1WN (1024 x 768) (±10%) T- 2 CPWX12WN (1280 x 800) (±10%) Screen size (diagonal) 4 : 3 screen 16 : 9 screen Projection distance Screen height Screen height Projection distance Screen height Screen height min. max. min.
2 0 F-3 CONTROL MONITOR OUT AUDIO OUT AC IN LAN HDMI USB DC5V 0.5A TYPE A USB TYPE B COMPUTER IN1 COMPUTER IN2 S-VIDEO VIDEO AUDIO IN2 AUDIO IN1 ・ Suspended from the ceiling ・ On a horizontal surf.
21 ENGLISH F-4 CONTROL MONITOR OUT AUDIO OUT AC IN LAN HDMI USB DC5V 0.5A TYPE A USB TYPE B COMPUTER IN1 COMPUTER IN2 S-VIDEO VIDEO AUDIO IN2 AUDIO IN1 F-5 Y C B /P B C R /P R COMPONENT VIDEO OUT L R AUDIO OUT VIDEO OUT L R AUDIO OUT L R AUDIO OUT S-VIDEO OUT CONTROL MONITOR OUT AUDIO OUT AC IN LAN HDMI USB DC5V 0.
22 CONTROL MONITOR OUT AUDIO OUT AC IN LAN HDMI USB DC5V 0.5A TYPE A USB TYPE B COMPUTER IN1 COMPUTER IN2 S-VIDEO VIDEO AUDIO IN2 AUDIO IN1 RGB IN F-6 Monitor Speakers (with an ampli er).
23 ENGLISH [unit: mm] 306 221 77 83 AC IN F-7.
NOTE • The information in this manual is subject to change without notice. • The manufacturer assumes no responsibility for any errors that may appear in this manual. • The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.
Hitachi America, Ltd. Digital Media Division 900 Hitachi way , Chula Vista CA 91914-3556 USA CANADA T el: +1 -800-225-1741 ► http://www .hitachi-america.
Een belangrijk punt na aankoop van elk apparaat Hitachi CPWX12WN (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hitachi CPWX12WN heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hitachi CPWX12WN vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hitachi CPWX12WN leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hitachi CPWX12WN krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hitachi CPWX12WN bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hitachi CPWX12WN kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hitachi CPWX12WN . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
