Gebruiksaanwijzing /service van het product CR 13VA van de fabrikant Hitachi
Ga naar pagina of 37
PO W ER T OOLS TECHNICAL DA T A AND SERVICE MANUAL RECIPROCA TING SA W CR 13V A SPECIFICA TIONS AND P ARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT LIST No.
1. PRODUCT NAME ............................................................................................................... . ........... 1 2. MARKETING OBJECTIVE ....................................................................................
- - - 1 - - - 1. PRODUCT NAME Hitachi 130 mm (5") Reciprocating Saw , Model CR 13V A 2. MARKETING OBJECTIVE There is increasing demand for a high-speed and powerful saber saw in overseas markets. The new Model CR 13V A, which features a powerful motor and a swing cutting action, has been developed to meet that market demand.
- - - 2 - - - 4-1. Selling Point Descriptions (1) Fast cutting speed The Model CR 13V A can cut various construction materials fast and efficiently thanks to the high-power motor whose maximum output is over 1000 W (Model CR 10V : 680 V).
- - - 3 - - - (3) Saw blade can be mounted in either direction, upward or downward The Model CR 13V A is convenient for cutting materials on the floor or near window frames, and also for plunge cutting on plywood panels because the saw blade can be installed upside down.
- - - 4 - - - (5) Dust- and water-resistant triple-sealing construction <patent pending> The Model CR 13V A has a triple-sealing construction to protect from the large amount of dust generated when cutting construction materials, autoclaved lightweight concrete, etc.
- - - 5 - - - 4-2. Descriptions of patent pending No. Overseas Japan Descriptions Patent Blade holder of saber saw A detachable mechanism that enables one-hand mounting and removal of saw blades witho.
- - - 6 - - - 5. SPECIFICA TIONS Max. cutting size Steel pipe outer diameter 130 mm (5") Wood thickness (for Europe) 300 mm (for USA) 5" Mild steel plate 19 mm (3/4") Power source AC single phase 50 or 60 Hz T ype of switch Enclosure T ype of motor Full load current Weight Stroke Number of strokes Max.
- - - 7 - - - 5-2. Optional Accessories The cutting speed of the Model CR 13V A is substantially higher than that of the current model, however , the conventional HCS blades may be broken in heavy applications such as house demolition, etc. T o cope with this problem, the BI-MET AL blades shown in T able 2 are provided.
- - - 8 - - - (2) BI-MET AL blades The blade numbers of BI-MET AL blades in T able 2 are engraved in the vicinity of the mounting position of each blade. Select appropriate blades by referring to T able 2 and 3 below . T able 2: BI-MET AL blades Below 3.
- - - 9 - - - 6. COMP ARISONS WITH SIMILAR PRODUCTS 6-1. For USA Market M a k e r HIT A CHI Model CR 13V A 120 11.0 1-1/4 0 - - 2,800 1,070 18.1 6.5 4.1 8.8 126.0 91.0 *T&D Plastic & Rubber (Swing) CR 10V P E S 120 10.0 10.0 10.0 1-1/4 0 - - 2,900 --- --- --- 17.
- - - 10 - - - Swing cutting Orbital cutting Orbital cutting Orbital cutting function is not provided. Orbital cutting function is not provided. Orbital cutting Orbital cutting Orbital cutting function is not provided. 0 10 20 30 40 50 CR 13V A CR 10V A B C D E F Cutting time (sec.
- - - 11 - - - Swing cutting Orbital cutting Orbital cutting function is not provided. Orbital cutting 0 10 20 30 40 50 CR 13V A B C D E F Cutting time (sec./cut) Straight cutting Swing or orbital cutting A Orbital cutting Orbital cutting function is not provided.
- - - 12 - - - 7-3. Cutting Wood with Saw Blade Installed Upside Down HIT ACHI genuine blade No. 121 for cutting wood A piece of lauan lumber 130 mm (5") in width and 43 mm (1.69") in thickness Pressing force about 4 kgf (8.8 lbs.) Swing cutting Orbital cutting function is not provided.
- - - 13 - - - 7-4. Cutting Operation for Long Blade Life The service life of a saw blade may vary depending on the operating conditions such as the type of cutting action, pressing force, etc. Observing the following instructions can lengthen the service life of a saw blade, for reference.
- - - 14 - - - 8. PRECAUTIONS IN SALES PROMOTION In the interest of promoting the safest and most efficient use of the Model CR 13V A Reciprocating Saw by all of our customers, it is very important th.
- - - 15 - - - 9. REP AIR GUIDE 9-1. PRECAUTIONS IN DISASSEMBL Y AND REASSEMBL Y Please follow the precautions below for disassembly and reassembly procedures. The circled numbers in the following figures and the [Bold] numbers in the descriptions below correspond to the item numbers in the Parts List.
- - - 16 - - - Loosen the Nylock Bolt (W/Flange) M6 x 35 [47] which secures the fan of the armature ass'y (approximately two turns). Remove the four Machine Screws (W/W ashers) M5 x 60 [42] and then pull out the Gear Cover [31] from the main body .
- - - 17 - - - (3) Disassembly of the blade mounting section (Fig. 5) Remove the Retaining Ring (E-T ype) for D14 Shaft [2] from Plunger (A) Set [32] with a flatblade screwdriver . At this time, be careful that Spring (A) [19] is pushing against the retaining ring.
- - - 18 - - - (5) Disassembly of the Second Shaft (A) [64] section (Fig. 7) Remove the Retaining Ring for D17 Shaft [60] from Second Shaft (A) [64] . While holding the side surface of the Recipro Pla.
- - - 19 - - - (8) Disassembly of Handles (A) [74] and (B) [80] section (Fig. 10) Remove the six T apping Screws (W/Flange) D4 x 25 [43] . Remove the Grip Cover [81] by pulling it backward and remove Handle (A) [74] . Then, the Switch T rigger [76] can be removed.
- - - 20 - - - Fig. 13-a 2. Reassembly Reassembly can be accomplished by following the disassembly procedures in reverse. However , special attention should be given to following items. (1) Press-fitting the Recipro Plate [61] ass'y into Second Shaft (A) [64] (Fig.
- - - 21 - - - (3) Reassembly of the blade mounting section (Figs. 15, 16 and 17) Apply Doubrex 251 grease to the inner circumference of Holder Sleeve (B) [14] and the cam groove of Plunger (A) Set [32] .
- - - 22 - - - (4) Press-fitting plunger (A) into the plunger sleeve (Figs. 18 and 19) T ool required: Special repair tool J-317 Apply Nippeco SEP-3A grease to the sliding portion of plunger (A) and insert it into the Guide Sleeve Ass'y [9] . Insert the Pin D6 [54] into plunger (A).
- - - 23 - - - * Be careful not to damage W asher (F) [3] . (Fig. 21) W asher (F) has an oval shape to fit the inside of the Gear Cover [31] . Therefore, perform disassembly and reassembly so that washer (F) is properly aligned with the shape of the gear cover .
- - - 24 - - - 9-2. Lubrication (1) Nippeco SEP-3A grease Lip portion of the V -Ring [7] Inner circumference of the Swing Roller [53] Sphere portion of the Recipro Plate [61] Both sides of the Thrust Bearing [21] Inner circumferene of the Guide Sleeve Ass'y [9] and Metal (A) [8] Apply 45 g of Nippeco SEP-3A to the Gear Cover [31] .
- - - 25 - - - For stator ass'y , or for stator ass'y and noise suppressor For triac ass'y , or for triac ass'y and noise suppressor For cord For stator ass'y Noise suppressor Switch body T ube (D) Cord T erminal T riac ass'y Dial resistor T ube (D) For cord Fig.
- - - 26 - - - 10. CONFIRMA TION AFTER REASSEMBL Y 10-1. Lead Wire Precautions When connecting lead wires, be very careful not to remove the insulation covering of each lead wire more than needed. Also, ensure that the lead wires are not pinched between the mating surfaces of the handle.
- - - 27 - - - 1 1. ST ANDARD REP AIR TIME (UNIT) SCHEDULES MODEL 10 20 30 40 60 50 Fixed V ariable CR 13V A Work Flow Handle (A),(B) Switch Cord Cord Armor Switch Trigger Front Cover (A) Front Cover .
- - - 28 - - - SABER SA W Model CR 13V A 1999 • 12 • 20 ( E1 ) LIST NO. 0786 ELECTRIC T OOL P AR TS LIST.
- - - 29 - - - PARTS CR 13VA : ALTERNATIVE PARTS ITEM NO. CODE NO. DESCRIPTION NO. USED REMARKS 1 318-484 WASHER (E) 1 2 318-453 RETAINING RING (E-TYPE) FOR D14 SHAFT 1 3 318-457 WASHER (F) 1 4 878-609 O-RING (S-24) 1 5 318-458 FELT WASHER 1 6 318-460 SEAL SLEEVE 1 7 318-459 V-RING 1 8 318-463 METAL (A) 1 9 318-462 GUIDE SLEEVE ASS'Y 1 INCLUD.
- - - 30 - - - CR 13VA ITEM NO. CODE NO. DESCRIPTION NO. USED REMARKS 52 318-488 SWING RAIL 2 53 318-492 SWING ROLLER 2 54 318-491 PIN D6 1 55 HITACHI LABEL 1 56 600-3DD BALL BEARING 6003DDCMPS2S 1 57 318-475 SUB SHAFT 1 58 318-476 BEARING COVER (B) 1 59 949-216 MACHINE SCREW M4X10 (10 PCS.
- - - 31 - - - Printed in Japan (991220 N) : ALTERNATIVE PARTS * PARTS OPTIONAL ACCESSORIES CR 13VA ITEM No. CODE NO. DESCRIPTION NO. USED REMARKS * 85 500-434Z CORD 1 (CORD ARMOR D8.8) FOR USA * 85 500-455Z CORD 1 (CORD ARMOR D8.8) FOR CHNOR ITEM No.
- - - 32 - - - SABER SA W Model CR 13V A [For the U.S.A. and Canada only] 2000 • 2 • 15 ( E1 ) LIST NO. 0786 ELECTRIC T OOL P AR TS LIST.
- - - 33 - - - PARTS CR 13VA : ALTERNATIVE PARTS ITEM NO. CODE NO. DESCRIPTION NO. USED REMARKS 1 318-484 WASHER (E) 1 2 318-453 RETAINING RING (E-TYPE) FOR D14 SHAFT 1 3 318-457 WASHER (F) 1 4 878-609 O-RING (S-24) 1 5 318-458 FELT WASHER 1 6 318-460 SEAL SLEEVE 1 7 318-459 V-RING 1 8 318-463 METAL (A) 1 9 318-462 GUIDE SLEEVE ASS'Y 1 INCLUD.
- - - 34 - - - CR 13VA ITEM NO. CODE NO. DESCRIPTION NO. USED REMARKS 52 318-488 SWING RAIL 2 53 318-492 SWING ROLLER 2 54 318-491 PIN D6 1 55 HITACHI LABEL 1 56 600-3DD BALL BEARING 6003DDCMPS2S 1 57 318-475 SUB SHAFT 1 58 318-476 BEARING COVER (B) 1 59 949-216 MACHINE SCREW M4X10 (10 PCS.
- - - 35 - - - Printed in Japan (000215 N) : ALTERNATIVE PARTS * STANDARD ACCESSORIES CR 13VA ITEM No. CODE NO. DESCRIPTION NO. USED REMARKS 502 312831 CASE 1 551 8" BI-M ALLPURP Progressive Recip. Blade 1PC 1 See Item No.677 651 725300 6" HCS WOOD 6TPI Recip.
Een belangrijk punt na aankoop van elk apparaat Hitachi CR 13VA (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hitachi CR 13VA heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hitachi CR 13VA vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hitachi CR 13VA leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hitachi CR 13VA krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hitachi CR 13VA bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hitachi CR 13VA kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hitachi CR 13VA . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
