Gebruiksaanwijzing /service van het product DH 24PD van de fabrikant Hitachi
Ga naar pagina of 28
W ARNING: Improper and unsafe use of this power tool can result in death or serious bodily injury! This manual contains important information about prod- uct safety . Please read and understand this manual before operating the power tool. Please keep this manual avail- able for others before they use the power tool.
2 — CONTENTS — Page IMPORT ANT INFORMA TION ................................................................................... 3 MEANINGS OF SIGNAL WORDS ........................................................................... 3 SAFETY .......
3 IMPORT ANT INFORMA TION Read and understand all of the operating instructions, safety precautions and warn- ings in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions.
4 SAFETY GENERAL SAFETY RULES W ARNING : Read and understand all instructions. Failure to follow all instructions listed below , may result in elec- tric shock, fire and/or serious personal injury . SA VE THESE INSTRUCTIONS 1. Work Area (1) Keep your work area clean and well lit.
5 (2) Dress properly . Do not wear loose clothing or jewelry . Contain long hair . Keep your hair , clothing, and gloves away from moving parts. Loose clothes, jewelry , or long hair can be caught in moving parts. (3) A void accidental star ting. Be sure switch is off before plugging in.
6 (2) When servicing a tool, use only genuine Hitachi replacement par ts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instruction may create a risk of electric shock or injury .
7 17. Never leave tool running unattended. T urn power off. Don ’ t leave tool until it comes to a complete stop. 18. Carefully handle power tools. Should a power tool be dropped or struck against hard materials inadvertently , it may be deformed, cracked, or damaged.
8 DOUBLE INSULA TION FOR SAFER OPERA TION T o ensure safer operation of this power tool, HIT ACHI has adopted a double insula- tion design. “ Double insulation ” means that two physically separate.
9 Fig. 1 SPECIFICA TIONS Motor Single-Phase, Series Commutator Motor Power Source Single-Phase, 115V 60Hz Current 5.7A Capacity Concrete: 1/8" ~ 15/16" (3.4mm ~ 24mm) Steel: 1/2" (13mm) W ood: 1-1/4" (32mm) No-Load Speed 0 – 1050/min.
10 APPLICA TIONS Rotation and striking function 䡬 Drilling anchor holes 䡬 Drilling holes in concrete 䡬 Drilling holes in tile Rotation only function 䡬 Drilling in steel or wood (with optional accessories). 䡬 T ightening machine screws, wood screws (with optional accessories).
11 6. Mounting the drill bit (Fig. 2) (1) T o attach a drill bit (SDS-plus shank), fully pull the grip in the direction of the arrow as shown in Fig. 2 and insert the drill bit as far as it will go while manu- ally turning. (2) By releasing the grip, the drill bit will be secured.
12 drill bits which have 6-17/32" (166 mm), 6-19/64" (160 mm) and 4-21/64" (110 mm) overall length. 䡬 Dump particles after every two or three holes when drilling.
13 CAUTION: 䡬 When the drill bit touches an iron reinforcing rod, the bit will stop immediately and the rotary hammer will react to revolve. Therefore please grip the side handle and handle tightly as shown in Fig. 7. 3. Using the dust-collecting adaptor and dust bag.
14 (2) Adjusting the dust-collecting adaptor . a) Adjusting the position of the dust- collecting adaptor . After firmly inserting the drill bit, loosen the wing bolt and drill bit tip and the end of the dust-collecting adaptor in contact with each other (see Fig.
15 4. When not using the dust-collecting adaptor When removing the dust-collecting adaptor and the dust bag to use as a normal rotary hammer , insert the pro- vided cap in the hose attachment hole. (see Fig.14) After removing the dust bag, the air blowing out from the at- tachment hole is reduced and no air will blow onto your face.
16 6 . When driving machine screws (Fig. 17) First, insert the bit into the socket in the end of chuck adaptor (D). Next, mount chuck adaptor (D) on the main unit using procedures described in 6 (1), (2), (3), put the tip of the bit in the slots in the head of the screw , grasp the main unit and tighten the screw .
17 8. How to use the drill bit (taper shank) and the taper shank adaptor . (1) Mount the taper shank adaptor to the rotary hammer . (Fig. 18) (2) Mount the drill bit (taper shank) to the taper shank adaptor . (Fig. 18) (3) T urn the switch ON, and drill a hole in prescribed depth.
18 MAINTENANCE AND INSPECTION W ARNING: Be sure to switch power OFF and disconnect the plug from the receptacle during maintenance and inspection. 1. Inspecting the drill bits Since use of a dull tool.
19 ACCESSORIES W ARNING: Accessories for this power tool are mentioned in this Instruction Manual. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage. NOTE: Accessories are subject to change without any obligation on the part of the HIT ACHI.
20 T aper mode Code No. Applicable drill bit 7/16" (11 mm) 31/64" (12.3 mm) 303617 1/2" (12.7 mm) 9/16" (14.3 mm) 73/128" (14.5 mm) 11/16" (17.5 mm) 303618 27/32" (21.5 mm) A-taper 303619 B-taper 303620 External dia.
21 <Outer wedge type with the female screw> Anchor size W 1/4" W 5/16" W 3/8" (6.3 mm) (8 mm) (9.5 mm) Overall Length 10-15/64" 10-15/64" 6-19/64" 10-15/64" (260 mm) (260 mm) (160 mm) (260 mm) Code No.
22 4. Bolt placing operation with Chemical Anchor . (rotation + striking) Standard socket ( on the market ) (SDS-plus shank) 1/2" (12.7 mm) Chemical Anchor Adapter (Code No.
23 7. Driving Screws (rotation only) Phillips Driver Bit Bit No. Screw Size Length Code No. No.2 1/8" ~ 3/16" (3 – 5 mm) 31/32" (25 mm) 971511Z No.3 1/4" ~ 5/16" (6 – 8 mm) 31/32" (25 mm) 971512Z 8. Dust cup, Dust collector (B) Dust cup Code No.
24.
25.
26.
27.
Nippon Bldg., 6-2, Ohtemachi 2-chome, Chiyoda-ku, T okyo 100, Japan 706 Code No. C99082861 N Printed in Japan.
Een belangrijk punt na aankoop van elk apparaat Hitachi DH 24PD (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hitachi DH 24PD heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hitachi DH 24PD vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hitachi DH 24PD leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hitachi DH 24PD krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hitachi DH 24PD bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hitachi DH 24PD kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hitachi DH 24PD . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
