Gebruiksaanwijzing /service van het product P50S601 van de fabrikant Hitachi
Ga naar pagina of 78
PLASMA TELEVISION O p e r a t i n g G u i d e f o r P 5 0 S 6 0 1 IMPORTANT SAFETY INSTRUCTIONS.......................................................................................2-3 FIRST TIME USE ..................................................
Important Safety Instructions SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HIT ACHI PLASMA TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI plasma televisions. Safety is also foremost in our minds in the design of these units.
3 Important Safety Instructions Power source This plasma television is designed to operate on 120 volts 60 Hz, AC current. Insert the power cord into a 120 volt 60 Hz outlet.
4 Accessories First time use Check to make sure you have the following accessories before disposing of the packing material. Power Cord Remote Control 1.5V batteries Power Swivel Table Top Stand (included) Two “AA” size, CAUT ION: 1. Ceili ng m ounting is not recom mend ed.
A A B 4 in. 10 cm 12 in. 30 cm 50 " 5 1. Using metallic wire (two places) fasten the set to the clamping screw on the rear of the Plasma TV as shown below . Securing to a Wall 2 . Keep the Plasma television 4 inches away from the wall except when mounted using the wall mount bracket.
6 Pass the AC cord through Clamp #1 and connect The AC cord, power swivel cable and the signal cables can all be held together with Clamp #2 (included on the accesories bag). AC CORD Clamp #2: Use this clamp to hold the AC cord, power swivel connector and the signal cables.
7 How to set up your new HIT ACHI Plasma T elevision STEP (1) : Please locate t he STAND METAL on the back of the TV . This m etal is use to hold the TV and the Base ; so it needs to remove 4 screws from the STAND base in order to separate the TV from the Base.
8 First time use How to set up your new HIT ACHI Plasma T elevision VIEWING The best pictur e is seen by si tting directly in front of the TV and about 10 to 18 feet from the screen. During daylight hours, reflections from outside light may appear on the screen.
9 First time use 300-Ohm T win Lead This outdoor antenna cable must be connected to an antenna adapter (300-Ohm to 75-Ohm). Phono or RCA Used on all standard video and audio cables which connect to inputs and outputs located on the television’ s rear jack panel and front control panel.
10 First time use Quick Reference Remote Control Buttons and Functions In addition to controlling all of the functions on your HIT ACHI Plasma TV , the new remote contr ol is designed to operate different types of devices, such as, DVD Players, CBL (Cable Boxes), set-top-boxes, satellite receivers, and VCRs.
11 First time use PUSH TO OPEN CONTROL DOOR FRONT VIEW PUSH EJECT UPGRADE CARD (SERVICE USE ONL Y) ! " # $ % & ' Press this button to turn the Plasma Television ON/ OFF. It can a lso b e tur ned ON/ OFF by remo te control. The “MAIN POWER” button must be at stand-by mode.
12 First time use REMOTE CONTROL sensor Point your remote at this area when selecting channels, adjusting volume, etc. ! INPUT- FRONT JACKS I NP U T - FR O N T p ro v id e c om po s it e V i d eo ja c ks f or connecting equipment with this capability , such as a DVD player or Camcorders .
13 First time use Rear Panel Connections % # " $ ' ! ( & * Antenna Input To switch betwee n C able and Air input, go to the Channel Manager option to change the signal source CABLE or AIR.
14 First time use PUSH EJECT UPGRADE CARD (SERVICE USE ONL Y) The FRONT panel jacks are provided as a convenience to allow you to easily connect HDMI or DVI signals from a DVD, Set Top Box , Video Gam.
15 First time use The FRONT pane l jacks are provided a s a convenience to a llow you to easily connect a camcor der , DVD, V ideo Game and a VCR as shown in the following examples: NOTE:1. Completely insert connection cord plugs when connecting to front panel jacks.
16 First time use NOTE: Cables are optional, except when specified. HDMI DIGITAL OUTPUT CAPABILITY HDMI OUTPUT HDMI to HDMI VCR #1 Cable TV coaxial cable 2-Way signal splitter Outside Antenna ANT IN O.
17 First time use Tips on Rear Panel Connections • S-VIDEO, Y - P B P R , or HDMI connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature.
First time use 18 Back of VCR OUTPUT VCR Video CONNECTING A VIDEO AND STEREO AUDIO SOURCE TO INPUT1 ~ INPUT-FRONT 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (V ID EO) jack , as sho wn o n th e R ea r Pane l to the right.
19 First time use C ON NE C TI NG A CO M PO NE N T SO U RC E W IT H H DM I O R 1. Connect the HDMI or DVI to HDMI connection cable from the output of the HDTV set top box or DVD player to the HDMI input as shown on the Rear panel below .
20 First time use : Y -P B P R . 1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the Rear panel below . 2. Connect the cable from the P B /C B OUT or B- Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (P B) jack.
21 F ir s t t im e u s e CONNECTING A VIDEO AND MONAURAL AUDIO SOURCE TO INPUT 1 ~ FRONT INPUT 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (V IDE O) jac k, as s how n o n t he Re ar Pa nel on th e right.
22 The Remote Control In addition to controlling all the functions on your HIT ACHI Plasma TV , the new remote control is designed to ope rate different types of VCRs, cable bo xe s, se t- top -b ox es, s at el li te re ce iv er s, D VD pl ay er s, and other audio/video equipment with one touch.
23 The Remote Control How to Use the Remote to Contr ol Y our TV NOTE: For automatic DAY/NIGHT picture mode settings, see page 5 0 . POWER button Press this button to turn the TV set on or off when th e re mot e is in T V m od e. (S ee pa ge 2 2 fo r ins tr uc ti on s on how to set the remote control to TV mode).
How to Use the Remote to Contr ol Y our TV 24 The Remote Control IMA G E INPUT IMA G E INPUT IMA G E INPUT IMA G E INPUT 1 2 16:9 ST ANDARD 2 Use this aspect mode to display 16:9 sources like HDTV and DVD’s preserving the original 16:9 aspect ratio showing 100% of the size.
25 How to Use the Remote to Contr ol Y our TV The Remote Control NOTE: 1. Press the INFO button again or the EXIT button to return to normal viewing. 2.
26 How to Use the Remote to Contr ol Y our TV The Remote Control VOLUME (VOL), MUTE button Pre ss th e VOLU ME butt on ( 왖 o r 왔 ) un til y ou obt ain the desired sound level. To reduce the sound to one half of normal volume (SOFT MUTE) to answer the telephone, etc.
27 The Remote Control FUNCTION FOR YOUR CABLE BOX. This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote system of your cable box (refer to pages 32-33 for pre-codes). 1. Turn ON your cable box.
28 The Remote Control YOUR SET-TOP-BOX/SATELLITE RECEIVER. This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your set- top-box/satellite systems (refer to pages 32-33 for pre- codes).
29 The Remote Control FUNCTION FOR YOUR DVD PLAYER. This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of your DVD player (refer to pages 32-33 for pre-codes). 1. Turn ON your DVD player.
30 The Remote Control YOUR VCR/PVR (Personal Video Recorder). This remote is designed to operate different types of VCRs/PVRs. You must first program the remote to match the remote system of your VCR/PVR (refer to pages 32-33 for pre-codes). 1. Turn ON your VCR/PVR.
31 The Remote Control INPUT ACCESS This optional feature allows the user of the remote control to setu p it’s SOURCE SELECT button to acces s the specified input of the TV. Setup for this feature is applicable to the remote control’s normal mode only and only applies to the DVD, PVR /VCR and SAT/CBL modes.
The Remote Control 32 Remote Contr ol Codes Cable BRAND Codes General Instrument ........ 0869 Daewoo ......................... 0045 , 0278 , 0020, 0561 1479 A BC ........................ 0003, 0008, 0011 GOI................................. 0775, 1775 1278 Panasonic .
33 Remote Control Codes The Remote Control DBS/PVR Codes Enterprise 0591 Sony 0533,1533,0864,1033, Combo BRAND ESA 0821,1268 1431 Hughes Network Systems 0739 Fisher 0670,1919 Sova 1122 Philips 0739 Fu.
34 On-Screen Display NOTE: The On Screen Display ( OSD ) for the different submenus shown in next pages are for illustration purposes only, therefore; doesn't reflect the actual apearance of the OSD of your HITACHI Plasma TV. 1. Press MENU on the remote control to display the 2.
35 Timers Channel Manager On-Scr een Display T reble Adjust the treble. Bass Adjust the bass. Balance Adjust the balance. Audio Source Select between three Audio Sources. Internal Speakers Select internal or external speakers. Auto Noise Cancel Eliminates the noise between stations.
36 Video Select to adjust picture settings and improve pi ctur e q ual it y. Y ou can i nde pe nden tly cu st omiz e e ach o f the Video Inputs to your preference to increase viewing performance and pleasure depending upon the video program being viewed.
37 Video Color T emperature Set this to Hig h for cooler co lor with more b lue, set to Med ium for more na tural color, se t to Standard f or accurate color or set to Black/White for more reddish color. Black Enhancement Use this function to enhance the shadow detail in dark scenes using the settings off, low , middle and high.
2. Vertical Position setting returns to "0" automatically after TV power On/Off. 38 Reset Video Settings This function allows you to Reset the Video Menu Settings of the pr esent input and return it to the Day -Dynamic VIDEO mode. 1. Use 왖 , 왔 to highlight functions.
Audio Select to adjust the TV to your preference and to improve the sound quality . 1. Press 왖 or 왔 to select menu item. 2. Press 왗 or 왘 to adjust the function. 3. Press to quit the , or select to return to the main menu. NOTE: If TREBLE is selected you are adjusting treb le.
40 Audio Source Multi-Channel T elevision Sound will allow you to select STEREO (a stereo broadcast), MONO (monaural sound) used when receiving a weak stereo broadcast or SECOND AUDIO PROG (SAP) which may be a secondary language, weather report, etc. Internal Speakers This function is useful when setting up the external speakers.
On-Screen Display Channel Manager Select CHANNEL MANAGER to set your Antenna options, run Auto Channel Scan, Check Signal Meter and Set Channel List. 1. Press 왖 , 왔 to highlight functions. 2. Press the button or 왘 to select. Signal Meter Se lect S IGN AL ME TER whe n u sing an in do or o r o utd oo r antenna.
42 Channel List This function allows you to review which channels are labeled (ID) , which have been added to CHANNEL MEMORY (SCAN) , which are protected by LOCK and which are your F AVORITE (F A V) CHANNELS . 1. Use the CURSOR P AD to navigate the Channel List.
Locks This f unctio n will block out t he pic ture a nd sou nd of th e selected channel or video input. The code to enter the Locks feature is a four digit access code number. The factory preset code is 0000 . Use the NUMBER buttons to enter the access code.
44 Movie Ratings Use Movie Ratings to prevent viewing of any movie that you feel may be inappropriate due to its content. 1. Use the CURSOR PAD 왖 , 왔 to select the MOVIE RATING category that you want to block. 2. Press SELECT to block the MOVIE RA TING that you have selected.
Locks TV Ratings Use TV RATINGS to prevent the viewing of any TV program that you feel may be inappropriate due to its content. 1. Use the CURSOR PAD 왖 , 왔 to select the TV RATING category that you want to block. 2. Press SELECT to block the TV RAT ING that you have selected.
46 Canadian Ratings (Eng) Use CANADIAN RA TINGS (ENG) to block any type of movie and television program in Canada that you feel might be inappropriate in its content. 1. Us e t he C U RS O R PA D 왖 , 왔 t o s el e ct t he C ANADIAN RATINGS (ENG) category that you want to block.
47 Locks Canadian Ratings (Fr n) Use CANADIAN RATINGS (FRN) to block Canadian French programs according to various program ratings that you feel might be inappropriate in its content. 1. Use the CURSOR PAD 왖 , 왔 to select the CANADIAN RATINGS (FRN) category that you want to block.
Program Title. . . . . . . . Cable 888-001 11:30AM 11:55AM REGION 5 KDEF-DT Multi DTVCC CF-18 ans+ 1080i 10:35 AM o t u A Pr o gram Title Program Time Source CH ID/Input ID Current Time Receiving Sign.
Select TIMERS to set your Clock, Sleep Timer, Event Timer and Day/Night Timer. 1. Use the CURSOR buttons 왖 or 왔 to highlight the function to be adjusted. 2. Press the SELECT button to select. Set The Clock The Clock must be adjusted before you can use the SET EVENT TIMER or DA Y/NIGHT TIMER feature.
50 Timers Set Sleep Timer Select this feature to set your SLEEP TIMER from 30 minutes to 3 hours (30 minute increments). 1. Press the CURSOR P AD 왘 repeatedly to set your Timer from and Set Day/Night Timer S elect this feature to activate and set your TV’s DA Y/NIGHT PICTURE MODE automatically .
51 Timers Set Event Timer This function will automatically operate the Plasma TV viewing reservation of a program. If the clock is not set, you can not use this function and the screen at right wi ll appear. The message on the screen will disappear after 3 seconds, then the screen automatically goes to the clock setup mode (see page 49).
52 Setup Select SETUP when setting your TV up for the first time. 2. Press the SELECT button to select. S et The Menu Options Setup the Language and background of the Menu OSD. Set The Language This feature will allow you to select any one of three differ ent languages for all on-screen displays.
53 Set The Menu Background This function allows you to choose from two menu backgrounds. SET THE MENU BACKGROUND (SHADED OR SOLID) of your choice. Use the CURSOR PAD 왗 or 왘 to select shaded or solid. 2 . Select SOLID for a black background (no picture can be seen behind menu screen), select SHADED and a light background is visible.
54 Setup Set The Inputs Use this feature to give a name to any of the video inputs. 1. Press the CURSOR P AD 왖 , 왔 to highlight the video inputs. 2.
55 Setup Set The Cl osed Caption s Closed Captions are the dialogue, narration, and/or sound effects of a television program or home video which are displayed on the TV screen. Your local TV program guide denotes these programs as or . 1. Us e the CURS OR PAD 왗 , 왘 , 왖 and 왔 to highl ight and select the function to change.
56 Setup Se lect The Quick Start Option This feature will select QUICK START UP options. Set this feature to ON to have the TV tune channels (both Analog and Digi tal) quickly wh en first turnin g the TV on. Set this feat ure to OFF to save electri city.
57 On-Screen Display Power Swivel This feature controls the motorized stand. It allows the customer to turn the Plasma Television left or right using the remote control. This feature is only available when the Table Top Stand is connected (see page 6).
58 Equipment Care and T r oubleshooting TROUBLESHOOTING Your HITACHI Plasma Television incorporates advanced power surge protection technology designed to protect against component or circuit damage due to external or internal voltage power surges. IF YOUR TELEVISION SHOULD APPEAR TO HA VE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE: 1.
59 Useful Information Reception Problems IGNITION NOISE: Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances.
Useful Information 60 Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
61 Useful Information All specifications, weights, and dimensions are subject to change without prior notice. Please access www.hitachi. us /tv for detailed specifications and dimensions for custom installations. UltraVision Digital is a registered trademark of Hitachi Home Electronics (America), Inc.
62 Useful Information Rear View, Use as Reference for Wall Mount Bracket Set Dimensions Units Inches 48-13/16 2- 9/16 2- 9/16 34-11/16 32- 5/16 20- 3/16 19-15/16 17- 9/16 43- 9/16 24-11/16 5- 1/16 3-10/16 1- 7/16 16-10/16 12 24-13/16 12 11-12/16 12- 2/16 8-7/16 mm 1240.
63 Useful Information HOME ELECTRONICS DIVISION HIT ACHI has made every effort to assure you hours of trouble free operation from your unit. However, should you require service, a network of HITACHI Authorized Service Facilities has been established in all 50 states and Puerto Rico.
64 Useful Information Look on the right side of the TV. Locate the LABEL where it shows the information related to MODEL NAME and SERIAL #. HITACHI Service Department will require this information in order to give y ou the proper support regarding your questions.
End User License Agr eement for HIT ACHI DTV Software END USER LICENSE AGREEMENT FOR HIT ACHI DTV SOFTW ARE IMPORTANT – READ CAR EFULLY: This End Us er License Agreement for HIT ACHI DTV Software (t.
130 L ic en s e Ag re e me nt s OPERATING SYSTEM LICENSE INFORMATION This HITACHI TV incorporates certain open source operating system software distributed under the GNU GENERAL PUBLIC LICENSE Version 2 and GNU LESSER GENERAL PUBLIC LICENSE Version 2.
The licenses for most software are designed to take away your f reedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.
132 In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
133 TO, THE IMPLIED WARRANTIES OF MERCHANT ABILITY AND F ITNESS FOR A P ARTICULAR PURPOSE. THE ENTIRE RISK AS T O THE QUALITY AND PERFORMAN CE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REP AIR OR CORRECTION.
134 Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.
135 straightforwardly into another language. (Hereinaft er , translation LVLQFOXGHGZLWKRXWOLPLWDWLRQLQWKHWHUPPRGL¿FDWLRQ "Source code" for a work means the preferred form of the work for making PRGL¿FDWLRQV to it.
136 a work containing portions of the Library , and distribute that work under terms of your choice, provided that the terms permit PRGL¿FD tion of the work for the customer's own use and revers.
137 or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time.
Appendixes 138 Appendix A: Picture Format for Each Input Source Aspect Specifications Yes : Selectable 웎 : Un-selectable Input Auto Aspect Aspect Signal Aspect Video ID 16:9 Standard 1 16:9 Standard.
Appendixes 139 (Continuation) I nput A uto A s pec t A s pe c t S igna l A s pec t V ide o ID 1 6 : 9 Standard 1 16:9 Standard 2 16:9 Zoom 4:3 Standard 4:3 Ex panded 4:3 Zoom 1 4:3 Zoom 2 HDMI 1 H D M.
140 Index A Accessories, . . . . . . . . . . . . . . . . . . . . . . . . . .4 Antennas (Connecting), . . . . . . . . . . . . . . . . .8 Aspect Ratio . . . . . . . . . . . . . . . . . . . . .24, 38 Audio Bass Boost . . . . . . . . . . . . . . . . . . .
Notes.
Notes.
Een belangrijk punt na aankoop van elk apparaat Hitachi P50S601 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hitachi P50S601 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hitachi P50S601 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hitachi P50S601 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hitachi P50S601 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hitachi P50S601 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hitachi P50S601 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hitachi P50S601 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
