Gebruiksaanwijzing /service van het product SBLE2-ML120201 van de fabrikant Hitachi
Ga naar pagina of 54
StarBoard Link EZ2 User ’ s Guide SBLE2-ML120201 Read this User's Guide and carefully retain it for future re ference. Before using t his product, ca refully read an d fully understand the safety instructio ns. S tore this User's Guide near by for ease of reference.
.
1 StarBoar d Link EZ2 Englis h Notices Reproducti on or r eprinting, without perm ission, of t his User' s Guide or any pa rt there of is prohibited. The contents of this User's Guide are subject to change with out prior notice. Every effort has been mad e to ens ure that this User's Guide is complete and correct.
2 StarBoar d Link EZ2 Englis h Pr oduct Assurance Pr ovisions This product is limit ed to use in the c ountry whe re the user bought this product. For warranty details, refer to "4. Appendix 4.6 Produ ct W arranty Policy" at th e end of this User's Guide.
3 StarBoar d Link EZ2 Englis h Intr oduction Thank you v ery much for pur chasing Hitachi Solutions’ s S tarBoard Link EZ2 (hencefor th referred to as "StarBoard"). This User's Guide has been cr eated for people who already have a wo rking knowledge o f personal computers (hencefort h re ferred to as "PC").
4 StarBoar d Link EZ2 Englis h Safe Handling Markings and Symbols V arious m arkings and sy mbols are use d in this User's Gui de and on this pr oduct, to ensure the safe and cor rect use of t his product and to prevent pers onal injury a nd property damage.
5 StarBoar d Link EZ2 Safe Handling Englis h (1) Precautions Regarding Operation W ARNINGS Do not make mo difications. Do not m ake any adjustm ents, repairs , or modi fications not given in this User's Guide as doing so may lead to personal injury or damage to the product.
6 StarBoar d Link EZ2 Safe Handling Englis h (2) Dealing with T r ouble CAUTIONS What to do in case of emission of smoke, strange odor , or strange noise If an abnormal co ndition such as emission of sm oke, strange odor , or strange noise happens to occur for some reason, immediately disconnect the prod uct's USB cable from the PC.
7 StarBoar d Link EZ2 Safe Handling Englis h NOTICE Disconnect the USB cable during extend ed periods of non-use. For safety reasons, disconnect the USB cable if the produ ct is not going to be used for an extended p eriod of time. Failure to comply may result in malfunction.
8 StarBoar d Link EZ2 Safe Handling Englis h (5) Precautions Regarding Setup Envir onment W ARNINGS Do not place in a location w ith flammable or c orrosive gas. Placing this pr oduct in a loc ation where there is fl ammable or corrosive gas m ay result in fire or damage to this product.
9 StarBoar d Link EZ2 Safe Handling Englis h NOTICE Do not use this product in location s subject to high temperatur e or high humidity . This product' s usage environ ment conditio ns: T emperature: 5°C – 35°C Humidit y: 20%RH – 80%RH (no c ondensat ion) Do not set up in locations subject to vibration and/or shock of impact.
10 StarBoar d Link EZ2 Safe Handling Englis h Careful thought was giv en to the cautions on this device and in th is User's Guide. However, unanticipated circumst ances might occur . When operating this product, users themselves must exercise caution as well as follow instructions.
11 StarBoar d Link EZ2 Englis h Safe Handling Notice Contents Page(s) - Select a level and stable positio n. - Do not set it up near eq uipment that m ight generat e electromagnet ic waves or radio freque ncies, such as radio transm itters, te levisions, co pying machi nes or air conditioners.
12 StarBoar d Link EZ2 Englis h Contents Contents 1. Intr oductio n .................................................................................................................. 1-1 1.1 Prepar ati ons .............................................
13 StarBoar d Link EZ2 Englis h Contents 4.1 T rouble shooting ............................................................................................................ ......... 4-1 4.2 Regularly Auto Sensor Adjustment (For W indows)..............
1-1 E n g lis h StarBoar d Link EZ2 Introduction 1. Intr oduction 1.1 Preparations This chapter describes the preparations to be made bef ore using S tarBoard.
1-2 E n g lis h StarBoar d Link EZ2 Introduction 1.2 Parts Check After unpacking, make s ure that a ll the following parts are present. 1.2.1 S tarB oard [1] Parts No.
1-3 E n g lis h StarBoar d Link EZ2 Introduction 1.2.2 S tylus Pen (opt ion) [1] Parts No. Name Qty (1) S tylus pen 2 (1) 1.2.3 Electro nic Pen (option ) [1] Parts No.
1-4 E n g lis h StarBoar d Link EZ2 Introduction 1.3 Role of Each Part 1.3.1 S tarB oard (1) Digitizer Receives information regarding characters or images draw n with the pe n or the user's finger , and transmits this data to the PC. (2) Status LED The connection st atus is di splayed by t he color and lighting status of the L ED.
1-5 E n g lis h StarBoar d Link EZ2 Introduction 1.3.2 Electro nic Pen (option ) (1) Battery cover Open the cove r when inse rting or replacing the battery . Refer to page 3-6 in this User's Guide for details. (2) Side button s Mouse Operati ons assigned to these buttons.
2-1 E n g lis h StarBoar d Link EZ2 Assembly and Setup 2. Assembly and Setup Be sure to follow the precautions belo w when installing the StarBoar d. Important Use on a flat surface. This product is designed so that stable in put is achieved when use d on a flat surface .
2-2 E n g lis h StarBoar d Link EZ2 Assembly and Setup 2.1 Installing the S tarBoard Software 2.2 Installing the Devices (U sing the Installation W izard) - For W indo ws users, run "Start" → "All Programs" → "StarBoa rd Link EZ Setup Wi z a r d " .
2-3 E n g lis h StarBoar d Link EZ2 Assembly and Setup 2.3 Installing the Devices (When th e installation wizard is not used) If this prod uct is being used in an envi ronment in which the installation wizard cannot be used, refer to the procedure below to install the devices.
2-4 E n g lis h StarBoar d Link EZ2 Assembly and Setup 2.3.2 Installing the Reflective Bars (1) Attach the reflective bars t o the bottom side of the installa tion surface in accorda nce with the width of the projection area. Attach so that the silver surface of the re flective bars is facin g inwards, and so there are no gaps.
2-5 E n g lis h StarBoar d Link EZ2 Assembly and Setup (4) Attach the corner piece to the lower left and lower right corners of the reflective bars. When installing ont o a wall where magnet s cannot be used, fix the reflec tive bars with wood screws.
2-6 E n g lis h StarBoar d Link EZ2 Assembly and Setup *If the projection size is larger than 82 inches, use 2 reflective bars on the bottom side. Use joint piec e to connect two reflective bars. NOTICE The gap betw een the curso r and your finger (o r pen) wi ll become bi g in the l ower 13cm (5 inc hes) of the di gitizer .
2-7 E n g lis h StarBoar d Link EZ2 Assembly and Setup 2.3.3 Installing th e Digitizer ・ Installing with Magnets Align the center of the digitizer with the center of the projectio n a rea, 5cm (2 inches) above the projection area, and install so it is parallel with the edge of the projection area.
2-8 E n g lis h StarBoar d Link EZ2 Assembly and Setup (2) Align the center of the digitizer with th e cente r of the projection area, 5 cm (2 inches) above the projection area, and install so it is parallel with the edge of the projection area.
2-9 E n g lis h StarBoar d Link EZ2 Assembly and Setup (2) Connect the bundled USB exte nsion cable to the computer . USB extension cable.
2-10 E n g lis h StarBoar d Link EZ2 Assembly and Setup 2.3.5 Adjustin g the Sens or ・ Items to Check Before Making Sensor Adjustm ents The following error may app ear while using this produ ct.
2-1 1 E n g lis h StarBoar d Link EZ2 Assembly and Setup [2] "Camera Adjustment W izard S tart" window appears. Press "All Adjust." [3] Press “Finish” This completes sensor adjustment. After m aking adjustm ents, check that i nput can be performed normally .
2-12 E n g lis h StarBoar d Link EZ2 Assembly and Setup 2.3.5.2 Se nsor Adjustm ent Procedure (Mac version) [1] Press the "OK" button on the "LSaDrv T ouch Sensor Error" dialog box displayed on the Mac scree n. [2] Sta rt the sensor adjustment wizard.
2-13 E n g lis h StarBoar d Link EZ2 Assembly and Setup [4] "Adjustment completed" will be shown after sensor adjustment. Press "OK" to close th e dialog. If an er ror such as the fo llowing appe ars, clic k the "OK" butt on and then per form adjustm ent again while referring to Section 2.
2-14 E n g lis h StarBoar d Link EZ2 Assembly and Setup 2.3.6 Positionin g Alignment Select "MENU" on the Sta rBoard Software toolbar → "Settings" → "S tarBoard" → "Calibrate" → "OK". and t hen perform position ali gnment.
3-1 StarBoar d Link EZ2 How to use Englis h 3. How to Use 3.1 How to Use T ouch Mode This section gi ves a basic des cription of how to us e the board in touch m ode. 3.1.1 Character Input T o input cha racters, use y our finger or the stylus pe n (sold separately).
3-2 StarBoar d Link EZ2 How to use Englis h - Using the stylus pe n and Electroni c pen Use the pen on the projection area with your body kept sufficiently away , so that your palm and elbow do not touch the pr ojection area.
3-3 StarBoar d Link EZ2 How to use Englis h CAUTION Do no strike the whiteboard or wall for cefully with the stylus pen, bend it, or apply an excessive load to it. Failure to comply may result in damage to the stylus pen or personal inj ury . Important Do not place the stylus pen onto the r eflective bar .
3-4 StarBoar d Link EZ2 How to use Englis h 3.2 Electronic Pen Input and Finger Input Y ou can select the following input met hods for use with S tarBoard Link EZ2.
3-5 StarBoar d Link EZ2 How to use Englis h [2] Select the i nput met hod you want t o use from "Input met hod", and pre ss the "OK" but ton.
3-6 StarBoar d Link EZ2 How to use Englis h 3.3 How to User the Electronic Pen This section gi ves a basic des cription of how to use t he electronic pe n (option). 3.3.1 Insert ing the Battery Perform the preparations fo r using t he electronic pe n.
3-7 StarBoar d Link EZ2 How to use Englis h 3.3.2 Usin g the Electro nic Pen T o use the electronic pe n to draw characters or images, place the tip of the electronic pen on the projection area and then m ove the pen. When you release the ti p of the elect ronic pen from the projection area, the writing is complete.
3-8 StarBoar d Link EZ2 How to use Englis h 3.3.3 Basic Operations of t he Electronic Pe n In the default settings of the el ectronic pen, the pen tip but ton is set to the left b utton of the mouse in W indows and the main button click in Mac.
3-9 StarBoar d Link EZ2 How to use Englis h 3.4 S tart Method 3.4.1 S tart Me thod (W indows version ) (1) Connect the USB cable of digitizer to the PC. (2) T urn on the power switch of the projector . (3) T urn on the power switch of the PC to start W indows.
3-10 StarBoar d Link EZ2 How to use Englis h If the positions of the pen tip and cursor are out of alignment, select "MENU" on the StarBoard Software toolbar → "Settings" → "StarBoard" → "Calibrate," and then perform position alignment.
3-1 1 StarBoar d Link EZ2 How to use Englis h (7) St art "Go" → "Applications" → "Lsadrv" → "LsCamW iz," and t hen adjust the sensor in accordance with the procedure on page 2-10.
4-1 Englis h StarBoar d Link EZ2 Appendix 4. Appendix 4.1 T roubleshooting Before assuming th e product is broken, be sure to check adju stments, proper handling procedures, the po ssibility of faulty cable conn ections, etc.
4-2 Englis h StarBoar d Link EZ2 Appendix Recognition-Related Pr oblems Problem What to check What to do The controller must be reset and the system restarted. Disconne ct the USB ca ble and reconnect it. If this does not solve the problem, restart the PC.
4-3 Englis h StarBoar d Link EZ2 Appendix Input-Related Pr oblems Problem What to check What to do This may be due to faulty contact of electronic pen batteries. Remove the ba tteries from the electronic pen and re-install them. Are batteries used up? Replace the batteries.
4-4 Englis h StarBoar d Link EZ2 Appendix 4.2 Regularly Auto Sensor Adjustment (For W indows) While using StarBoard, auto sensor adj ustme nt will execute regularly . T o use StarBoard comfortably this functi on is recom mended t o use. Y ou cannot use this Adjustment for Mac.
4-5 Englis h StarBoar d Link EZ2 Appendix [2] Sensor adjusting screen will be displayed during au to adjustment. Do not touch the board surface until auto adjustm ent completed. [3] Following window will be displayed when sensor au to adjustment finished.
4-6 Englis h StarBoar d Link EZ2 Appendix 4.3 System Specifications Item Specification Model name StarBoard Link EZ2 Detection method Infrared image sensor system* 1 Digitiser resolution 0.05mm Sampling rate Approx. 100 points/second when using (USB1.
4-7 Englis h StarBoar d Link EZ2 Appendix 4.4 Proper Care and Cleaning Clean the StarBoard periodically so that you may use it for a long time to come. (1) Digitizer Cleaning ・ When cleaning the digitizer , use a soft cloth da m pened with a diluted neutral cleansing agent that does not contain a po lishing compound .
4-8 Englis h StarBoar d Link EZ2 Appendix 4.6 Product W arranty Policy 1. During the free warranty service period, if a malfunction occurs during normal use, the malfunction will be corrected without charge, according to the provisions of the warranty .
4-9 Englis h StarBoar d Link EZ2 Appendix (8) In the event of a malfunction in this product caused by the connection to th is product of equipment other tha n the equipment specified by our c ompany . (9) In th e event that there is no abnormality in this produ ct, but a defect in a part other than this product was detected or remedied.
Een belangrijk punt na aankoop van elk apparaat Hitachi SBLE2-ML120201 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hitachi SBLE2-ML120201 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hitachi SBLE2-ML120201 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hitachi SBLE2-ML120201 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hitachi SBLE2-ML120201 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hitachi SBLE2-ML120201 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hitachi SBLE2-ML120201 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hitachi SBLE2-ML120201 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
