Gebruiksaanwijzing /service van het product AM14TC van de fabrikant Hobart
Ga naar pagina of 20
MODEL AM14F , AM14T , & AM14TC DISHW ASHERS MODELS AM14F ML-110975 AM14T ML-110973 AM14TC ML-110974 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.
– 2 – POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED FROM THE LOCAL GAS SUPPLIER. IMPORT ANT IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN UNIT(S) AT MAIN SHUTOFF VALVE AND CONTACT THE LOCAL GAS COMPANY OR GAS SUPPLIER FOR SERVICE.
– 3 – TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 4 – Installation, Operation, and Care of MODEL AM14F , AM14T , AM14TC DISHW ASHERS SA VE THESE INSTRUCTIONS GENERAL The AM14T, AM14TC, and AM14F dishwashers are semi-automatic rack-type machines. On model AM14T (Fig. 1) the doors open on opposite sides of the machine allowing the rack to move straight through.
– 5 – DO NOT attempt to operate this dishwasher in the chemical sanitizing mode without a properly installed, NSF-listed, chemical sanitizer feeder (not supplied with machine). Contact an authorized detergent representative for information about a chemical sanitizer feeder.
– 6 – On models AM14T and AM14TC, dish tables should be turned down and fitted into the dishwasher (Fig. 2). Use an NSF approved sealer between table and tank lip to prevent leakage. Fasten the tables to the tank lip with truss head screws. Dish tables are not required with model AM14F.
– 7 – WATER CONNECTION A suitable water hammer arrestor should be installed in the water line just ahead of the dishwasher. Without Electric or Gas Booster Water Heater The water supply line is connected to the line strainer (Fig. 1) with 3 / 4 " pipe.
– 8 – Static inlet gas pressure should not exceed 14" W.C. for either natural or propane gas. The minimum value is for purpose of input adjustment. The gas valve (Fig. 3) is provided with a pressure tap to measure the gas pressure downstream, which is also the manifold pressure.
– 9 – VENTING REQUIREMENTS — WITH GAS TANK HEAT The Hobart AM14F / AM14T / AM14TC dishwasher equipped for gas tank heat is not provided with a flue collar and is not intended to have the flue directly connected to a ventilation system. However, the products of combustion must be vented to the outside air.
– 10 – The Rate of air flow required for a vent hood is calculated using the following definitions (Fig. 6): Q = Rate of Air Flow in Cubic Feet Per Minute or [ CFM ] Required for the Hood. A = Area of Hood Opening = (L x W) in Feet 2 D = Clearance Height = Distance in Feet from lower lip of hood to top of dishwasher chamber.
– 11 – ELECTRICAL CONNECTIONS WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE THAT YOU ARE WORKING ON THE CIRCUIT.
– 12 – OPTIONAL EQUIPMENT CONNECTIONS — Vent Fan and Gas Booster WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES.
– 13 – DETERGENT, RINSE AID, OR SANITIZER DISPENSERS — Tubing Installation All detergent, rinse aid, and / or sanitizer dispensers must have all connections sealed against leakage.
– 14 – OPTIONAL EQUIPMENT CONNECTIONS — Detergent, Rinse Aid, Sanitizer Dispensers WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES.
– 15 – Fig. 13 PO W ER O N / O F F FILL CYCLE WASH 1 2 4 6 Power Switch Cycle Switch Wash / Fill Switch PL-52759 Fig. 11 PL-41 178-1 MANUAL / AUTO SWITCH W ASH / RINSE SWITCH POWER SWITCH READOUT .
– 16 – Models AM14T / AM14TC In Automatic mode, the M ANUAL / A UTO switch (Fig. 12) is on A UTOMATIC and the W ASH / R INSE switch is O FF . The wash and rinse cycles begin automatically. The wash cycle begins when the machine doors are closed. The rinse cycle begins when the wash cycle is completed.
– 17 – PL-40468-1 AM14T Shown Rinse Nozzle Knurled Disk Rinse Arm Wash Arm PL-40809-1 AM14T Shown Rinse Nozzle Rinse arm W ash arm Knurled Disk – Unscrew and support both arms on release. CLEANING T he machine m ust b e thoroughly cleaned at the end of each working shift or at least daily.
– 18 – MAINTENANCE WARNING : DISCONNECT ELECTRICAL POWER SUPPLY (BOTH DISHWASHER AND BOOSTER IF APPLICABLE) AND PLACE A TAG(S) AT THE DISCONNECT SWITCH(ES) TO INDICATE THE CIRCUIT(S) ARE BEING WORKED ON BEFORE BEGINNING ANY MAINTENANCE PROCEDURE. Wash Arms Upper and lower wash and rinse arms (Figs.
– 19 – TROUBLESHOOTING Manual Reset Button on Pump Motor The motor is equipped with a gray manual reset button near the end cover of the motor. If the pump motor becomes overheated, the thermal overload protector will cause the motor to not operate.
– 20 – FORM 34555 ( Dec. 2000 ) PRINTED IN U.S.A. SYMPTOM POSSIBLE CAUSE Inadequate rinse or rinse water 1. Dirty line strainer causing reduced water flow. Turn off water supply, temperature is too low. remove strainer cap, withdraw and clean screen.
Een belangrijk punt na aankoop van elk apparaat Hobart AM14TC (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hobart AM14TC heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hobart AM14TC vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hobart AM14TC leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hobart AM14TC krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hobart AM14TC bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hobart AM14TC kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hobart AM14TC . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
