Gebruiksaanwijzing /service van het product HBA2E van de fabrikant Hobart
Ga naar pagina of 32
O P E R A T I O N 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com HBA RACK OVEN WITH ELECTRONIC OVEN CONTROL MODELS HBA1G GAS HBA2G GAS HBA1E ELECTRIC HBA2E ELECTRIC FORM 34757 Rev.
IMPORTANT FOR YOUR SAFETY — GAS OVENS — POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED FROM THE LOCAL GAS SUPPLIER.
– 3 – MODEL HBA RACK OVEN.
– 4 – TABLE OF CONTENTS GENERAL ............................................................................................................................................. 5 INSTALLATION ..........................................................
– 5 – OPERATION AND CARE OF MODEL HBA GAS RACK OVEN SA VE THESE INSTRUCTIONS GENERAL The Hobart HBA Rack Oven accommodates a roll-in rack. It is equipped with an electronic oven control for baking and/or steaming applications. A mechanism in the oven ceiling rotates the rack during baking.
– 6 – OPERATION HBA STANDARD CONTROLS HBA CONTROLS - STANDARD.
– 7 – Control Guide - Standard Button Action Display POWER Press to turn the oven Control panel displays are lit when the oven is on. Oven ON or OFF. defaults to Program 0. If oven is turned off and back on within 2 minutes, the oven will come up in the last mode and oven setting.
– 8 – Oven Preheat For best results, the oven must be preheated to bake temperature before baking begins. 1 . The door must be closed for oven to heat. The rack carrier will lift and rotate only during timed bake. NOTE: The rack carrier will be in the unload position from the last bake.
– 9 – Loading Procedure 1 . The rack carrier is equipped with a stop on both ends. For B lifts, ensure stop flap is in the up position to load the rack on the rack carrier. For C lifts, push rack stop to the left after rack is loaded. 2. Roll the rack into the oven so the end brackets channel onto the rack carrier.
– 10 – HBA ADVANCED CONTROLS HBA CONTROLS - ADVANCED.
– 11 – Control Guide - Advanced Button Action Display POWER Press to turn the oven Control panel displays are lit when the oven is on. Oven ON or OFF. defaults to Program 0. If oven is turned off and back on within 2 minutes, the oven will come up in the last mode and oven setting.
– 12 – Control Guide - Advanced (cont) Button Action Display Press to stop the BAKE The ON light is off when the BAKE TIMER is inactive. TIMER or silence the beeper after the BAKE TIMER has timed out. PROGRAM Press to select bake The PROGRAM window displays the number of the program.
– 13 – Oven Preheat For best results, the oven must be preheated to bake temperature before baking begins. 1 . The door must be closed for oven to heat. The rack carrier will lift and rotate only during timed bake. NOTE: The rack carrier will be in the unload position from the last bake.
– 14 – Loading Procedure 1. The rack carrier is equipped with a stop on both ends. For B lifts, ensure stop flap is in the up position to load the rack on the rack carrier. For C lifts, push rack stop to the left after rack is loaded. 2 . Roll the rack into the oven so the end brackets channel onto the rack carrier.
– 15 – • The oven monitors the heating system by comparing the current oven temperature to the set temperature. If a problem arises in the heating system or there is a heating system failure, both temperature displays will flash. If the problem continues, contact your authorized Hobart Bakery Systems service agency.
– 16 – PROGRAMMING THE OVEN Single Step Programming The program menu stores up to 99 programs that can be recalled by number when needed. A program is a set of baking instructions (temperature, bake, steam and airflow delay settings) that the operator defines for any baking operation.
– 17 – Multi-Step Programming Additional programs or steps can be entered within the original program number. Up to four individual steps can be added by the operator, each with different bake settings. For example, Program 1 has temperature, bake, steam and delay time settings set by the operator.
– 18 – Changing the Programs 1 . With the oven in the OFF mode, press and hold the UP arrow in the STEPS section. While pressing and holding the UP arrow, press the POWER ON button for 3 seconds. When the beep sounds, the oven is in program mode. 2 .
– 19 – Using the Programs 1 . Press the PROGRAM UP or DOWN arrows to select the desired program number (1-99). The TEMP , BAKE, STEAM and AIRFLOW DELAY settings are displayed. 2 . Confirm that the oven is at the set baking temperature. 3 . Slowly open the doors.
– 20 – CUSTOMIZED OPERATION The HBA oven standard and advanced controls have the capability of being customized to fit your own personal needs using the setup mode. Before entering the setup mode, read all the instructions to make sure you are completely clear on what to do.
– 21 – Setup Guide Setup Number Setup Item Display P 1 Maximum Temperature This is the maximum temperature at which the oven can be Setpoint set. Range is 50°F to 525°F (10°C to 274°C). P2 Preheat Temperature This is the default temperature setpoint when the oven is first turned on (Program 0).
– 22 – Setup Guide (cont) Setup Number Setup Item Display P14* Steam Timer Mode The STEAM TIMER can be set up to display in seconds or operate in food service mode. Select 0 for seconds or 1 for food service mode. P15* Interior Light Brightness This value is the brightness of the interior lights.
– 23 – CLEANING WARNING: DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. WARNING: THE RACK OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, SERVICING OR CLEANING THE RACK OVEN. WARNING: HOT AIR AND STEAM ARE RELEASED FROM THE OVEN INTERIOR WHEN THE LOADING DOOR IS OPENED.
– 24 – MAINTENANCE WARNING: THE RACK OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, SERVICING OR CLEANING THE OVEN. WARNING: HOT AIR AND STEAM ARE RELEASED FROM THE OVEN INTERIOR WHEN THE LOADING DOOR IS OPENED. TO AVOID BURNS, OPEN THE DOOR SLOWLY AND KEEP CLEAR OF THE OPENING.
– 25 – TR OUBLESHOO TING BURNERS WILL NOT LIGHT ON GAS OVEN 1 . Check that door is shut. 2 . Press the OFF button to turn the oven off and wait 5 minutes. 3 . Make sure the gas shutoff valve is in the ON position. 4 . Press the ON button to turn the oven back on.
– 26 – Clean and Vacuum Components and Control/Burner Compartment Area (Gas Only) 1 . Clean the control/burner compartment (Fig. 2) area of dust and/or lint accumulation. 2 . Vacuum the control/burner compartment floor of dust and/or lint accumulation.
– 27 – Inspect Door Components 1 . Check loading door latch. A. Check door gasket for good condition. If door gasket needs replacement, contact your local Hobart office for service. B. Check loading door latch. Latch must fully extend (Fig. 5) when door is closed and contacting door gasket.
– 28 – Inspect Air Louvers 1 . Check air louvers (shutters) (Fig. 9) inside oven and tighten any loose screws. 2 . Check oven interior, tighten or replace loose or missing panel screws. Also check floor anchors. Inspect Cavity Vent 1 . Check cavity vent for proper operation.
– 29 – Verify Ignition Module Safety Lockout Functions (Gas Only) 1 . Verify ignition module safety lockout functions. A . Turn main gas supply off to the oven. B. Open control panel door to gain access to burner compartment area. C. Turn the oven on.
– 30 – 3 . Verify draft inducer pressure switch (Fig. 15) operation. A . Set oven control to call for heat make sure convection fan is running. B. Disconnect tubing from draft inducer pressure switch (Fig. 15), burner flame should go out. C. Reconnect tubing and burner should establish a flame.
– 31 – D E D E E N S A Y P O C S R E B M U N L A I R E S / L E D O M R E N W O D E D N E M M O C E R T S I L K C E H C E C N A N E T N I A M E V I T N E V E R P S A G - S N E V O K C A R Y R E K A B .
NO TES – 32 – FORM 34757 Rev. A (Nov. 2003) PRINTED IN U.S.A..
Een belangrijk punt na aankoop van elk apparaat Hobart HBA2E (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hobart HBA2E heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hobart HBA2E vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hobart HBA2E leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hobart HBA2E krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hobart HBA2E bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hobart HBA2E kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hobart HBA2E . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
