Gebruiksaanwijzing /service van het product HR7E van de fabrikant Hobart
Ga naar pagina of 24
HR7E ROTARY OVEN N S T R U C T I O N S I 701 S. RIDGE A VENUE TROY , OHIO 45374-0001 937 332-3000 www .hobartcorp.com FORM 35508 Rev. C (May 2005) MODEL HR7E ROT AR Y OVEN MODEL HR7E STAINLESS STEEL I.
– 2 – © HOBART 2005 T ABLE OF CONTENT GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 3 – Installation, Operation and Care of MODEL HR7E ROT AR Y OVENS SA VE THIS MANUAL FOR FUTURE REFERENCE GENERAL The model HR7E Oven is a seven-spit rotary oven that features a full view tempered glass door and quartz lighting that promote visual appeal and stimulate customer interest.
– 4 – PLACING THE ROTOR IN THE OVEN The rotor must properly engage with the drive mechanism. Orient the rotor so that the end plate with square drive slots is on the same side of the oven as the drive arm. STEP 1: Stop the drive arm so it is in the down position (Fig.
– 5 – ELECTRICAL CONNECTIONS WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND / OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES.
– 6 – OPERA TION WARNING : HOT GLASS, GREASE AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING AND SERVICING THE OVEN. CONTROLS (Fig. 7) MAIN POWER SWITCH — Turns oven and controls on or off. PROGRAM — Enters program mode to modify a cook program; press P for 3 seconds.
– 7 – INITIAL STARTUP Power On Toggle the Main Power switch on the front panel of the oven to the ON position; the red indicator light on the switch comes on (Fig. 5). Idle Mode When the oven is first turned on, the display shows the time of day and the last operated program number.
– 8 – SAVING OR VERIFYING A COOK PROGRAM (PROGRAM 1 – 9) Begin from Idle Mode. Program display shows last operated program (0 – 9). • Select a program (1 – 9). Program 0 is Manual Mode and cannot be saved into memory. • Press P for 3 seconds to enter programming mode.
– 9 – Cooking 'Step 3' LED is lit. Time display blinks. • Enter the desired cook time from 0:01 (1 minute) to 6:00 (6 hours). • Press ENTER to accept (or, press CLEAR to void and reenter). An invalid entry produces a double beep. Entering 0:00 for the time turns step 3 off and skips to step 4.
– 10 – PROGRAMMED COOKING (Program 1 – 9) Begin from Idle Mode. The Program display shows the last operated program (0 – 9). • Select a saved cook program (1 – 9). Any programmed steps for the selected program are indicated by lit step LEDs.
– 11 – MANUAL COOKING (Program 0) Begin from Idle Mode. The Program display shows the last operated program (0 – 9). • Select manual mode by selecting program 0: [0, ENTER]. Cook Step 1 LED is lit. Time display blinks. • Enter the desired cook time from 0:01 (1 minute) to 6:00 (6 hours).
– 12 – HOLDING CYCLE (SILENCING THE 'END OF CYCLE' ALARM) After a cook cycle has been completed, the beeper sounds and the oven automatically executes the Hold cycle (Step 4 of the cooking program). The Hold cycle will not execute if it was programmed 'off', using Hold Temp = 000.
– 13 – ADDING COOK TIME • Press ADD 5 MIN during a cooking cycle to add 5 minutes of cook time to the current step of the program in process. Press during the end of cycle buzzer or during Hold cycle to add 5 minutes of cook time to the last step of the last operated program.
– 14 – SUGGESTED ROASTING GUIDELINES The suggested cooking times and temperatures in the table may require adjustment for proper doneness depending on initial product temperature, weight, size, shape and other factors.
– 15 – STEP 1 STEP 2 STEP 3 STEP 4 TEMPERATURE TIME STEP 1 STEP 2 STEP 3 STEP 4 TEMPERATURE TIME STEP 1 STEP 2 STEP 3 STEP 4 TEMPERATURE TIME STEP 1 STEP 2 STEP 3 STEP 4 TEMPERATURE TIME STEP 1 ST.
– 16 – Bring chickens from cooler. Check temperature — range should be from 37 ° F to 42 ° F. Insert approved popper, if available; it will pop out when chicken is done. PREPARING, TYING & SPITTING — CHICKENS ON V-SPITS The rotary oven is not designed to roast frozen foods.
– 17 – INCORRECT SPITTING — CHICKENS ON V-SPITS WRONG — Angle of spit is in line with breast. This will split the backbone and could possibly result in falling off the spit during cooking. WRONG — Legs and thighs are not on same side as breast.
– 18 – 1 2 Skip 3 4 Skip 5 6 Skip 7 WARNING : SPITS ARE SHARP. USE CARE WHEN LOADING PRODUCT. SPITTING — CHICKENS ON FORK SPITS Press pointed ends of spits into whole poultry so points go through the chest-wing and leg-thigh regions (Fig. 8).
– 19 – Loading V-Spits or Thermo-Wave Spits on the Rotor 1. Place pointed end of V-spit into small outside hole on non-drive side of rotor (Fig. 12). 2. Fit notched end of V-spit into appropriate holes on drive side of rotor (Fig. 13). 3. Make sure the spit is level.
– 20 – PERSONAL PROTECTIVE EQUIPMENT Chickens and accessories are hot. Use care during unloading by using appropriate personal protective equipment such as 18" insulated gloves, an apron, long sleeved clothing and closed toed shoes. UNLOADING ACCESSORIES FROM OVEN Opening the door does not stop the rotor, heaters or fan.
– 21 – CLEANING WARNING : DISCONNECT ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES BEFORE CLEANING OR SERVICING. Proper cleaning prolongs the life and productivity of the oven. The oven should be routinely cleaned throughout the day and thoroughly cleaned at the end of the day.
– 22 – CLEANING GUIDELINES FOR NONSTICK COA TED SURF ACES Abrasion and aggressive chemicals reduce the life of the nonstick coating. With proper care, the nonstick coated surface should provide a long life of easy-to-clean service. DO NOT do the following: • DO NOT use abrasive cleaning aids such as steel wool.
– 23 – MONTHLY CLEANING Clean ventilation grate and fan blades located in the top of the oven. 1. Remove ventilation grate by unscrewing nuts on both sides of vents. 2. Unscrew nut (clockwise) in center of fan blade. 3. Wash in a sink with warm soapy water.
– 24 – FORM 35508 Rev. C (May 2005) PRINTED IN U.S.A. MAINTENANCE WARNING : DISCONNECT ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES BEFORE CLEANING OR SERVICING. WARNING : HOT GLASS, GREASE, AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING AND SERVICING THE OVEN.
Een belangrijk punt na aankoop van elk apparaat Hobart HR7E (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hobart HR7E heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hobart HR7E vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hobart HR7E leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hobart HR7E krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hobart HR7E bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hobart HR7E kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hobart HR7E . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
