Gebruiksaanwijzing /service van het product C7015A van de fabrikant Honeywell
Ga naar pagina of 15
Honeywell C7015A Infrare d Flame Detector The C7015A Flame Detector includes a lead sulfide photocell that is sensitive to the infrared radiation emitted by the combustion offuels such as natural gas, oil, and coal. n q w n n Particularily suitable for combination or dual-fuel radiation is compatible with a wide range of flame applications.
C7015A SPECIFICATIONS l ORDERING INFORMATION Specifications SUPER TWELINE MODELS SUPER TRADELINE models offer features not available on TRADELINE or standard models, and are designed to replace a wide range of Honeywell and competitive controls.
WIRING CONNECTIONS: Nominal 30, 48 , or 96 in. [0.76, 1.22, or 2.44 ml leadwire+hvoNo. 18 AWG,flexible-tinnedconduc- tom; rated for 194°F [90” C]; twistedpair-onebrown and one white. Underwriters Laboratories Inc. listed: File No. MP268. Canadian Standards Association certified: Master file LR-95329-1.
C7015A OPERATION l INSTALLATION Operation OPERATION OF INFRARED DETECTORS Infrared detectors can be used with gas, oil, coal, or dual- fuel flames. Since more than 90% of the total flame radiation is infrared, these detectors receive ample radiation and can detect weak fkunes as well as flames of higher intensity.
C7015A INSTALLATION is available to facilitate flame sighting after the C7015A is pipe diameter is reduced, the effect is the same as adding an mounted. orifice plate to the pipe as discussed below. FIELD OF VIEW A lead sulfide photocell, like other photocells, views an area rather than a point.
C7015A INSTALLATION INSTALLING AN ORIFICE PLATE AnorificeplatewithahexagonalorificediameterofO.125 in. [3.2 mm] is available for the C7915A Infrared Flame Detector. The orifice can be mounted i n front of the cell in the seal-off adapter or in a standard 314 in.
C7015A INSTALLATION RESPONSE TO HOT REFRACTORY Although the infrared amplifier will not respond to steady radiation, as produced by hot refractory, be careful to protect the infrared detector from hot refractory radiation because of two possible conditions , shimmer and raa’iation saturation.
C7015A INSTALLATION CLEARANCE Make sure there will be enough mom to easily mount the sight pipe, flame detector, and all required accessories, and to remove th e flame detecto r for troubleshooting and servicing. INSTALLING THE SIGHT PIPE Thelocationofthesightpipeisthemostcriticalpartofthe installation.
c701 !?A INSTALLATION Fig. 8-installing lead sulfide photocell. CAP , MOUNTING PLUG-IN LEAD SULFIDE CELL (PART NO. 104662D) METAL CABLE SHIELDS LEADWIRES PHOTOCELL SOCKET EPOA FOCUSING LENS I Fig. O-Mounting C7015A Infrared Flame Detector (and accessories).
C7015A INSTALLATION l ADUSTMENTS AND CHECKOUT Fig. 1 O-Typical wiring of C7015A Infrared Fig. 1 l-Typical wiring of C7015A Infrared Flame Detector to nearby wiring subbase or Flame Detector to distant wiring subbase or terminal strip.
C7015A ADJUSTMENTS AND CHECKOUT and associated flame safeguard controls. Move the detector an d sight pipe around to sight the flame at various positions and angles. Try to get a maximum steady meter reading. The signal must be above the minimum acceptable current/voltage listed in Table 6.
C7015A ADJUSTMENTS AND CHECKOUT PILOT TURNDOWN TEST Ifthedetectorisusedtoproveapilotflamebeforethemain fuel valve( can be opened, perform a Pilot Turndown Test before welding the sight pipe into position. Follow the procedures in the instructions for the appropriate flame safeguard control, and the burner manufacturer instructions.
C7015A ADJUSTMENTS AND CHECKOU T l TROUBLESHOOTING n ! CAUTION FINAL CHECKOUT Before putting the burner into service, check out the installation by using the Checkout procedures in the instruc- tions for the appropriate flame safeguard control.
C7015A SERVICE n 1 CAUTION . 1. Onlyusequalifiedservicetechnicianstoattempt to service or repair flame safeguard controls and burner systems. 2. Open the master switch to disconnect power before removing or installing the detector. 3. If the C7015A is disassembled for any reason (e.
C7015A TABLE OF CONTENTS Table of Contents Page Application and Features 1 .................................................................................................................................................. 1 Specification s ...........
Een belangrijk punt na aankoop van elk apparaat Honeywell C7015A (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Honeywell C7015A heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Honeywell C7015A vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Honeywell C7015A leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Honeywell C7015A krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Honeywell C7015A bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Honeywell C7015A kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Honeywell C7015A . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
