Gebruiksaanwijzing /service van het product IS3480 QuantumE van de fabrikant Honeywell
Ga naar pagina of 210
.
Copyright © 2007 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced, transmitted, or stored in any for m or by any means without prior written consent, except by reviewer, who may quote br ief passages in a review, or provided for in the Copyright Act of 1976.
Table of Contents iii T ABLE OF C ONTENTS Introduction Symbol Key ................................................................................................. xi Bar Code Configuration Methods Single-Code Method ..................................
Table of Contents iv T ABLE OF C ONTENTS Section B: Supplements Two Digit Supplements/Redundancy ........................................................... 1 Five Digit Supplements/Redundancy ..........................................................
Table of Contents v T ABLE OF C ONTENTS ISBN Re-Formatting ..................................................................................... 9 ISSN Check Digit Transmission ................................................................. 10 ISSN Re-Formatting .
Table of Contents vi T ABLE OF C ONTENTS Same Symbol Time Outs.............................................................................. 8 Barcode Absence ......................................................................................... 9 LED Options .
Table of Contents vii T ABLE OF C ONTENTS Telepen......................................................................................................... 9 Plessey ......................................................................................
Table of Contents vii i T ABLE OF C ONTENTS Section J: Light Pen/Laser Emulation Enable Light Pen Mode ................................................................................ 1 Space/Bar Height ................................................
Table of Contents ix T ABLE OF C ONTENTS Section N: Miscellaneous Features Custom Defaults ........................................................................................... 1 Serial Configuration Mode ........................................
Table of Contents x T ABLE OF C ONTENTS Inter-Character Delays ............................................................................... 15 Inter-Character De lays .............................................................................. 16 Section P: USB .
Introduction xi I NTRODUCTION Your new scanner has been configured at the fa ctory with a set of default communication protocols. Since many host systems have unique formats and protocol requirements, Metrologic provides a wide range of configurabl e features that may be selected with the use of this bar code configuration guide.
Bar Code Configuration Meth ods xii B AR C ODE C ONFIGURATION M ETHODS Metrologic scanners can be bar code configured in two ways: the Single-Code Method and the M ulti-Code Method . Single-Code Meth od Most features can be enabled or disabled using the Single-Code Method.
Need to Start Over? xiii N EED TO S TAR T O VER ? Scan the Recall Default bar code. This will erase all previous settings and return to the scanner’s default communications protocol. • Keyboard Wedge interface scanners will load keyboard wedge defaults.
.
Code Types & Decode Rules A 1 S ECTION A UPC/EAN * Enable UPC/EAN Disable UPC/EAN ³ 1 00116 ³ 1 00106 * Enable UPC-A Disable UPC-A ³ 1 00216 ³ 1 00206 * Enable UPC-E Disable UPC-E ³ 1 00210 .
Code Types & Decode Rules A 2 S ECTION A UPC/EAN * Enable EAN-13 Disable EAN-13 ³ 1 00211 ³ 1 00201 * Enable EAN-8 Disable EAN-8 ³ 1 00214 ³ 1 00204 * Enable Auto Redundancy UPC-E Disable Auto.
Code Types & Decode Rules A 3 S ECTION A C ODE 128 * Enable Code 128 Disable Code 12 8 ³ 1 00113 ³ 1 00103 Enable UCC/EAN-28 ‘]C1’ Code Formatting Disable UCC/EAN-128 ‘]C1’ Code Formatting ³ 1 00314 ³ 1 00304 For Coupon Code 128, see Section B, page 5.
Code Types & Decode Rules A 4 S ECTION A C ODE 39 * Enable Code 39 Disable Code 39 ³ 1 00111 ³ 1 00101 Enable MOD 43 Check on Code 39 * Disable MOD 43 Check on Code 39 ³ 1 00213 The scanner will o nly scan Code 39 bar codes that have a valid M odulo 43 check digit.
Code Types & Decode Rules A 5 S ECTION A C ODE 39 Enable Full ASCII Code 39 * Disable F ull ASCII Code 39 ³ 1 00217 ³ 1 00207 Enable PARAF Support (Italian Pharmaceutical Codes) * Disable PARAF Support ³ 1 00215 The scanner will conv ert Code 39 bar codes to PARAF format.
Code Types & Decode Rules A 6 S ECTION A I NTERLEAVED 2 OF 5 * Enable Interleave d 2 of 5 (ITF) Disable Interleaved 2 of 5 (ITF) ³ 1 00115 ³ 1 00105 Enable MOD 10 Check on ITF * Disable MOD 10 Check on ITF ³ 1 00310 The scanner will o nly scan Interleaved 2 of 5 (ITF) Bar codes that ha ve a Modulo 10 chec k digit.
Code Types & Decode Rules A 7 S ECTION A I NTERLEAVED 2 OF 5 Enable ALT Check Digit ITF * Disable ALT Check Digit ITF ³ 1 00717 ³ 1 00707 Enable 12 Digit ITF Check Digit at 1 * Normal Check Digit ³ 1 00910 This feature requir es MOD 10 ITF Check Digit to be enabled.
Code Types & Decode Rules A 8 S ECTION A I NTERLEAVED 2 OF 5 ~ ITF Symbol Length Lock 1 † ~ ITF Symbol Length Lock 2 † ³ 9 01600 To specify a 1 st IT F symbol length lock, s can the abov e bar code and the appropriate code bytes located in Secti on M.
Code Types & Decode Rules A 9 S ECTION A S TANDARD 2 OF 5 Enable Standard 2 of 5 * Disable Standard 2 of 5 ³ 1 00110 ³ 1 00100 ~ Standard 2 of 5 Symbol Length Loc k ³ 9 01500 To specify a mi nimum number of ITF cha racters to be decoded, sc an the above bar code and the appropriate code bytes located in Secti on M.
Code Types & Decode Rules A 10 S ECTION A O THER 2 OF 5 C ODES Enable Matrix 2 of 5 * Disable Matrix 2 o f 5 ³ 1 00015 ³ 1 00005 Enable 15 Digit Airline 2 of 5 * Disable 15 Digit Airline 2 of 5 .
Code Types & Decode Rules A 11 S ECTION A O THER 2 OF 5 C ODES Enable 13 Digit Airline 2 of 5 * Disable 13 Digit Airline 2 of 5 ³ 1 00313 ³ 1 00303 Enable Hong Kong 2 of 5 * Disable Hong Kong 2 .
Code Types & Decode Rules A 12 S ECTION A C ODABAR * Enable Codabar * Disable C odabar ³ 1 00114 ³ 1 00104 Enable Dual Field Codaba r * Disable Dual Field Codaba r ³ 1 00012 ³ 1 00002 Enable Tab in Dual Codabar * Disable Tab in Dual Codabar ³ 1 08012 This feature requir es Dual Field Codabar to be enabled.
Code Types & Decode Rules A 13 S ECTION A C ODE 93 AND C ODE 11 * Enable Code 93 Disable Code 93 ³ 1 00112 ³ 1 00102 Enable Code 11 * Disable C ode 11 ³ 1 00013 ³ 1 00003.
Code Types & Decode Rules A 14 S ECTION A T ELEPEN Enable Telepen * Disable Tel epen ³ 1 00017 ³ 1 00007 Enable ALPHA Telepen * Disable ALPHA Telepen ³ 1 00016 ³ 1 00006.
Code Types & Decode Rules A 15 S ECTION A P LESSEY C ODES Enable MSI Plesse y * Disabl e MSI Plessey ³ 1 00212 ³ 1 00202 * No MSI Plessey Check Digit ³ 2 00704 The scanner will not tes t MSI Plessey bar codes for a check digit.
Code Types & Decode Rules A 16 S ECTION A P LESS EY C ODES Transmit MSI Plessey Check Di git * Do Not Transmit MSI Plessey Check Di git ³ 1 07711 This option works in conjunction with one or both of the Enabled MS I Plessey Mode options. ³ 1 07701 The scanner will not transmit MS I Plessey check digit characters .
Code Types & Decode Rules A 17 S ECTION A O THER D ECODE F EATURES Enable Double Bo rder Required/Large Inter-Character Space * Disable D ouble Border Required/Large Inter-Character Space ³ 1 00011 ³ 1 00001 ~ Minimum Symbol Length † ~ Symbol Length L ock † ³ 9 01800 Omnidirect ional defa ult is 4.
Code Types & Decode Rules A 18 S ECTION A C ONFIGURABLE C ODE L ENGTHS There are seven bar code lock lengths availabl e. Specific code types can be assigned to a lock length using the Multi-Code configuration method. Example: 1. Scan the enter/exit configuration bar code.
Code Types & Decode Rules A 19 S ECTION A C ONFIGURABLE C ODE L ENGTHS ~ Code Length Lock #3 ~ Code Type Lock #3 ³ 9 02400 ³ 9 02500 ~ Code Length Lock #4 ~ Code Type Lock #4 ³ 9 02600 ³ 9 027.
Code Types & Decode Rules A 20 S ECTION A C ONFIGURABLE C ODE L ENGTHS ~ Code Length Lock #6 ~ Code Type Lock #6 ³ 9 03000 ³ 9 03100 ~ Code Length Lock #7 ~ Code Type Lock #7 ³ 9 03200 ³ 9 033.
Code Types & Decode Rules A 21 S ECTION A RSS 14 F EATURES Enable RSS 14 * Disable RSS 14 ³ 1 00413 ³ 1 00403 * Transmit RSS 14 Check Digit Do Not Transmit RSS 14 Check Digit ³ 1 14900 ³ 1 149.
Code Types & Decode Rules A 22 S ECTION A RSS 14 F EATURES * Transmit RSS 14 Application ID Do Not Transmit RSS 14 Application ID ³ 1 14901 Application iden tifier “01” is transmitted by d efault.
Code Types & Decode Rules A 23 S ECTION A RSS L IMITED F EATU RES Enable RSS Limited * Disable RSS Limited ³ 1 00414 ³ 1 00404 * Transmit RSS Limited Check Digit Do Not Transmit RSS Limited Chec.
Code Types & Decode Rules A 24 S ECTION A RSS L IMITED F EATU RES * Transmit RSS Limited Application ID Do Not Transmit RSS Limited Application ID ³ 1 14904 Application iden tifier “01” is transmitted by d efault.
Code Types & Decode Rules A 25 S ECTION A RSS E XPANDED F EATURES Enable RSS Expanded * Disable RSS Expanded ³ 1 00415 ³ 1 00405 * Transmit RSS Expanded Symbol ogy ID Do Not Transmit RSS Expanded Symbol ogy ID ³ 1 14906 Symbology ident ifier “]e0” is transmitted by d efault.
.
Supplements B 1 S ECTION B S UPPLEMEN TS /R EDUNDANCY Enable Two Digit Supplements * Disable Two Digit Supplements ³ 1 01217 ³ 1 01207 * Enable Two Digit Redundancy Disable Two Digit Redundancy ³ 1 01212 Twice before acc epting data, the scann er will scan the bar code plus the two digit add on.
Supplements B 2 S ECTION B S UPPLEMEN TS /R EDUNDANCY Enable Five Digit Redundancy * Disable Five Digit Redundancy ³ 1 01211 Twice before acc epting data, the scann er will scan the bar code plus the five digit add on. ³ 1 01201 The scanner will not implement the fiv e digit redundancy feat ure.
Supplements B 3 S ECTION B S UPPLEMEN TS Enable Bookland ( 978) Supplement Requi rement * Disable Book land (978) Supplement Requi rement ³ 1 01417 ³ 1 01407 Enable 977 (2 digit) Supplemental R equi.
Supplements B 4 S ECTION B S UPPLEMEN TS Enable 434/439 German Supplemental R equirement * Disable 434/439 German Supplemental Requirement ³ 1 01415 ³ 1 01405 Enable 414/419 German Supplemental R eq.
Supplements B 5 S ECTION B S UPPLEMEN TS Enable # System 5 Requires Supplements * Disable # System 5 Requires Supplem ents ³ 1 01215 ³ 1 01205 Enable 8711685 Requ ires 5-Digit Su pplement * Disable 8711685 Requires 5-Digit Supplement ³ 1 07613 The scanner will r equire a 5-digit supplem ent to be scanned when an EAN-13 code begins with 8711685.
Supplements B 6 S ECTION B S UPPLEMEN TS Enable Code 128 ‘ ]C1’ Extended Code Format * Disable Code 128 ‘]C1’ Extended Code Format ³ 1 01411 The scanner will tr ansmit a ‘]C1’ at the begin ning of the code 128 portion of the coupon code.
Supplements B 7 S ECTION B S UPPLEMEN TS 400 msec to Fin d Supplemental ³ 3 01340 The scanner will a llot 400 milliseconds t o “find” an add on after a main U PC/EAN bar code has been scanned.
Supplements B 8 S ECTION B S UPPLEMEN TS * Beep Once on Supplements Beep twice on Supplements ³ 1 18406 ³ 1 18416 Enable ISBN Check Digit Transmission Disable ISBN Check Digit Transmission ³ 1 01315 This feature is n ot available with al l models.
Supplements B 9 S ECTION B S UPPLEMEN TS Enable Bookland t o ISBN Conversion * Disable Bookland to ISBN Conversion ³ 1 01317 This feature is n ot available with al l models. ³ 1 01307 Enable ISBN Re-Formatting * Disable ISBN Re-Formatting ³ 1 01316 This feature is n ot available with al l models.
Supplements B 10 S ECTION B S UPPLEMEN TS Enable ISSN Check Digit Transmission * Dis able ISSN Check Digit Transmission ³ 1 15115 ³ 1 15105 Enable ISSN Re-Formatting * Disable ISSN Re-Formatting ³ 1 15116 Transmit a hyphe n with the barcode.
Supplements B 11 S ECTION B S UPPLEMEN TS Enable Number Sy stem 4 Coupon Code 128 * Disable Number Sy stem 4 Coupon Code 9128 ³ 1 01012 Supports Coupon Code 128 for Number System 4 bar codes. ³ 1 01002 Enable UPC Discard * Disable UPC Discard ³ 1 01013 Supports UPC discard if t he Code 128 portion of the Coupon Code 128 is scanned.
.
Communications C 1 S ECTION C C OMMUNICATIONS * Enable RS-232 Load Keyboard W edge Defaults ³ 4 15554 The scanner will w ork with RS-232 ± 12V serial output.
Communications C 2 S ECTION C C OMMUNICATIONS Load OCIA Defaults Enable OCIA Output ³ 9 99993 Scan this before s electing Enable OCIA output. ³ 4 15544 Select this option if the communications requirement is an Optically Coupled Interface Adapter (OCIA).
Communications C 3 S ECTION C C OMMUNICATIONS Load Low Spee d External USB Defaults † Enable Low Speed USB † ³ 9 99978 † Refer to Section P for full speed USB opt ions.
.
Scanner Operation D 1 S ECTION D C ONFIGURATION M ODE O PT IONS Allow Configuration Mo de on Power-Up * A llow Configuration Mo de Anytime ³ 1 18117 The scanner can only enter MetroSet ® mode before any bar codes are sca nned. ³ 1 18107 Allow MetroSet ® configuration at any time.
Scanner Operation D 2 S ECTION D S CAN B UFFERS * 1 Scan Buffer 2 Scan Buffers ³ 3 18000 The scanner will s can one bar code in the sc an field and not scan a gain until the bar code is remov ed from the scan field f or the duration of the s ame symbol time out.
Scanner Operation D 3 S ECTION D S CAN B UFFERS 5 Scan Buffers 6 Scan B uffers ³ 3 18040 Same function as 2 Scan Buffers, but 5 bar codes are in the scan fiel d.
Scanner Operation D 4 S ECTION D R EDUNDANT S CANS * 0 Redundant Scan s 1 Redundant Scan s ³ 3 01100 Requires 1 good d ecode for a “good scan” . ³ 3 01110 Requires 2 consec utive decodes of the s ame bar code data for a “ good scan”.
Scanner Operation D 5 S ECTION D R EDUNDANT S CANS 6 Redundant Scan s 7 Redundant Scan s ³ 3 01160 Requires 7 consec utive decodes of the s ame bar code data for a “ good scan”. ³ 3 01170 Requires 8 consec utive decodes of the s ame bar code data for a “ good scan”.
Scanner Operation D 6 S ECTION D M ISCELLANEOUS D ECODE F EATURES * Enable Segmente d UPC Decoding Disable Segmente d UPC Decoding ³ 1 01113 Enabling segment ed UPC decoding aids in dec iphering damaged or inco mplete bar codes. ³ 1 01103 Disable this feat ure when bar codes are in good reading conditio n.
Scanner Operation D 7 S ECTION D D EPTH OF F IELD A DJUSTMENTS Do not change these settings un less instructed by a Metrologic repr esentative. * Optimize for Low Density Codes † Optimize for High D.
Scanner Operation D 8 S ECTION D S AME S YMBOL T IME O UTS These numbers determine the length of time before a bar code can be rescanned after it is removed from the scan field. Single code fixed settings in msecs of No, 50, 100, 200, 500, 1200 (1.2 sec), 2000 (2.
Scanner Operation D 9 S ECTION D S AME S YMBOL T IME O UTS Infinite Same Symbol Time Out ~ Variable Same Symbol Time Out ³ 1 18917 The scanner will not repetitively sc an the same bar code.
Scanner Operation D 10 S ECTION D LED O PTIONS Flash Green LED if Rescan Allowed * Do not flash Green LED if Rescan Allowed ³ 1 18313 This indicate s same symbol timeout has ela psed.
Scanner Operation D 11 S ECTION D LED O PTIONS * Las er LED High Intensity Laser LED Low Intensity ³ 2 43100 Laser LED Intensit y is High or Normal. ³ 2 43120 Laser LED is Low Inte nsity This feature is n ot available with al l models. * Sc an LED High Intensity Scan LED Low Intensity ³ 2 43102 Scan LED Intensity is High or Normal.
Scanner Operation D 12 S ECTION D B EEPER O PTIONS * Normal Tone Optional Tone 1 ³ 3 18575 ³ 3 18565 Optional Tone 2 Optional Ton e 3 ³ 3 18555 ³ 3 18545 Optional Tone 4 Optional Ton e 5 ³ 3 1853.
Scanner Operation D 13 S ECTION D B EEPER O PTIONS Optional Tone 6 No Beep ³ 3 18515 ³ 3 18505 * Enab le Good Scan Beep Disable Good Scan Beep ³ 1 41903 Enable good scan beep on power up.
Scanner Operation D 14 S ECTION D B EEPER O PTIONS Next Beep Tone Next Volume ³ 9 99975 ³ 9 99974 * Loudest Volume 2 nd Loudest Volume ³ 2 18500 ³ 2 18510 3 rd Loudest Volum e No Volume ³ 2 18520.
Scanner Operation D 15 S ECTION D B EEPER O PTIONS * Beep Once on Supplements Beep Twice on Supplements ³ 1 18406 ³ 1 18416 Enable Fast Beep * Disable Fast Beep ³ 1 18414 ³ 1 18404.
Scanner Operation D 16 S ECTION D B EEPER O PTIONS Beep on BEL Comman d * Ignore BEL Command ³ 1 18417 The scanner beep s when it receives a BEL charac ter from the host. If a number is sent within 20 0 msecs before the BEL c haracter, then the scanner will beep that number of times.
Scanner Operation D 17 S ECTION D I NTER - C HARACTER D ATA T RANSMISSION D ELAYS Use these codes to select the amount of delay between sending data characters and “Bar Code” records from the scanner to the host. This helps prevent the scanner from overflowing host input buffers.
Scanner Operation D 18 S ECTION D I NTER - C HARACTER D ATA T RANSMISSION D ELAYS No Inter-Character Delay ³ 8 18800 I NTER -R ECORD D ATA T RANSMISSION D EL AYS ~ Variable Inter-Record Delay ³ 9 19.
Scanner Operation D 19 S ECTION D C OMMUNICATION T IME O UT O PTIONS Enable Communications Time Outs * Disable Communic ations Time Outs ³ 1 18412 ³ 1 18402 * Beep Before Tran smit Beep After Trans mit ³ 1 18413 Scanner will beep before each label is tr ansmitted.
Scanner Operation D 20 S ECTION D C OMMUNICATION T IME O UT O PTIONS Short Communicat ions Time Out (1 sec) Long Communicat ions Time Out (4 secs) ³ 8191200 ³ 8191800 Three Beeps on Time Out * No Be.
Scanner Operation D 21 S ECTION D H OST S CANNER C OMMANDS Enable “D/E” Disable Command * Disable “D/E” Dis able ³ 1 18015 The scanner will d isable scan ning after it receives and ASCII “D” from the host dev ice. It will enable scanni ng when it rece ives an AS CII “E ”.
Scanner Operation D 22 S ECTION D H OST S CANNER C OMMANDS Motor “On/Off” Using M/O Commands † * Disable “M/O” Commands ³ 1 18213 The scanner will t urn the motor OFF after it receives an ASCII “O” character. T he motor will turn ON after the scanner receives an ASCII “M” character.
Scanner Operation D 23 S ECTION D H OST S CANNER C OMMANDS Enable S Command * Dis able S Command ³ 1 25610 ³ 1 25600 Enable EM Commands * Dis able EM Commands ³ 1 20610 Enable EM comm and. End of Medium (ctrl Y). The EM command sends a nd ID string then a sc anner status spread over two bytes.
Scanner Operation D 24 S ECTION D H OST S CANNER C OMMANDS Use DTR Scan Disable * Do not use DTR Scan Disable ³ 1 18115 The scanner will monitor the DTR input to determin e if scanning should be allowed. A +12V “active” level enables decoding. A -12V “inactive” level disables deco ding.
Scanner Operation D 25 S ECTION D H OST S CANNER C OMMANDS Activate on DC2 Character * Do Not Activate on DC2 Character ³ 1 18110 ³ 1 18100 Transmit “NO READ” if DC2 Activated Do Not Transmit .
Scanner Operation D 26 S ECTION D P OWER S AVE M ODES Always Power Save Mode † No Power Save Mode † ³ 1 18617 The scanner enter s power save mode immediat ely after power-up and after each bar code sc anned. † † For us e with omnidirectio nal scanners only.
Scanner Operation D 27 S ECTION D P OWER S AVE M ODES Power Save in 20 Minutes † Power Save in 30 Minutes † ³ 8186200 The scanner enter s power save mode if th e scanner remains idle for 2 0 min. † † For use with omni directional scanners only.
Scanner Operation D 28 S ECTION D P OWER S AVE M ODES Laser OFF Power Save Mode †† Laser Motor OFF Power Save Mode †† ³ 3 19420 The laser turns OFF after a configured period of non-use. This feature is n ot available with al l models. ³ 3 19430 The laser and mot or turns OFF after a configured period of non-use .
Scanner Operation D 29 S ECTION D P OWER S AVE M ODES * Enable Power Save Switch Disable Power Save Switch ³ 1 19700 This feature is n ot available with al l models.
Scanner Operation D 30 S ECTION D J APANESE D OUBLE F IELD S UPPORT To support Japanes e Double Field Bar Cod es, first make sure y ou have your sc anner configured t o the following sett ings.
Scanner Operation D 31 S ECTION D J APANESE D OUBLE F IELD S UPPORT Upper Code 1 Character 1 Upper Code 1 Character 2 ³ 9 30000 ³ 9 30100 Lower Code 1 Character 1 Lower Code 1 Character 2 ³ 9 30200.
Scanner Operation D 32 S ECTION D J APANESE D OUBLE F IELD S UPPORT Lower Code 2 Character 1 Lower Code 2 Character 2 ³ 9 30600 ³ 9 30700 Upper Code 3 Character 1 Upper Code 3 Character 2 ³ 9 30800.
Scanner Operation D 33 S ECTION D J APANESE D OUBLE F IELD S UPPORT Upper Code 4 Character 1 Upper Code 4 Character 2 ³ 9 31200 ³ 9 31300 Lower Code 4 Character 1 Lower Code 4 Character 2 ³ 9 31400.
Scanner Operation D 34 S ECTION D J APANESE D OUBLE F IELD S UPPORT Japanese Trial Ti me Enable Code Sele cts ³ 9 38800 Scan the above bar code followe d by the 3 code bytes in Section M th at represent the time out value desire d if in special co de select mode.
Scanner Operation D 35 S ECTION D T EST M ODES Scanability ON * Scanability OFF ³ 1 18017 The scanner will enter scanability tes t mode. Do not enable unless instructed to by a Metrologic representative.
.
Prefixes/Suffixes E 1 S ECTION E C ONFIGURABLE P REFIXES , A LL D ATA Scan the Enter/Exit Configura tion Mode bar code before trying to set this feature.
Prefixes/Suffixes E 2 S ECTION E C ONFIGURABLE P REFIXES , A LL D ATA ~ Configurable Prefix Character #6 ~ Configurable Prefix Character #7 ³ 9 04000 Assigns a 6 th confi gurable prefix character. ³ 9 04100 Assigns a 7 th confi gurable prefix character.
Prefixes/Suffixes E 3 S ECTION E C ONFIGURABLE ID C HARACTERS , C ODE S PECIFIC * Use Configurable Code ID Bytes as Prefixes Us e Configurable Code ID Bytes as Suffixes ³ 1 05507 User configured, code specific ID bytes a re transmitted before the data.
Prefixes/Suffixes E 4 S ECTION E C ONFIGURABLE ID C HARACTERS , C ODE S PECIFIC ~ Configurable EAN-8 ID † ~ Configura ble EAN-13 ID † ³ 9 05800 † While using the Multi-Code met hod, scan this bar code followed by the 3 code byte bar c odes in Sect ion M that represent a unique ID charac ter to be associated w ith this bar c ode type.
Prefixes/Suffixes E 5 S ECTION E C ONFIGURABLE ID C HARACTERS , C ODE S PECIFIC ~ Configurable Code 93 ID † ~ Configurable Co de 11 ID † ³ 9 06300 † While using the Multi-Code met hod, scan this bar code followed by the 3 code byte bar c odes in Sect ion M that represent a unique ID charac ter to be associated w ith this bar c ode type.
Prefixes/Suffixes E 6 S ECTION E C ONFIGURABLE ID C HARACTERS , C ODE S PECIFIC ~ Configurable Standard 2 of 5 ID † ~ Configurable Interleaved 2 of 5 ID † ³ 9 07100 † While using the Multi-Code.
Prefixes/Suffixes E 7 S ECTION E C ONFIGURABLE ID C HARAC TERS C ODE S PECIFIC ~ Configurable MSI Plessey ID † ~ Confi gurable UK Plessey ID † ³ 9 06500 † While using the Multi-Code met hod, sc.
Prefixes/Suffixes E 8 S ECTION E S TANDARD P REFIX C HARACTERS Enable STX Prefix * Disable STX Pref ix ³ 1 16615 The scanner will tr ansmit a S tart of T e X t (ASCII 02H) before each bar c ode. ³ 1 16605 Will not transmit a S tart of T e X t (ASCII 02H) before each bar code.
Prefixes/Suffixes E 9 S ECTION E S TANDARD P REFIX C HARACTERS Enable UPC Prefix ID * Disable UPC Prefix ID ³ 1 16617 When enabled, th e scanner will transmit a prefix before any UPC/EAN bar code. The prefixes are a s follows: A (UPC-A), E0 (UPC-E), F (EAN-13), and FF (EAN-8).
Prefixes/Suffixes E 10 S ECTION E S TANDARD P REFIX C HARACTERS Enable Nixdorf ID Characters * Disable Nixdorf ID Characters ³ 1 07917 This option transm its code identifiers before e ach bar code for many Siemens/Nixdorf registers . ³ 1 07907 This option will not transmi t Siemens/Nixdorf c ode identifiers.
Prefixes/Suffixes E 11 S ECTION E S TANDARD P REFIX C HARACTERS Enable TEC Register Format ID Characters Dis able TEC Register Format ID Characters ³ 1 24710 ³ 1 24700 Enable TEC MA1530 ID Character.
Prefixes/Suffixes E 12 S ECTION E S TANDARD P REFIX C HARACTERS Enable Manufactu rer ID Prefix * Disable Ma nufacturer ID Prefix ³ 1 05512 Transmits “METROLOGIC” before all bar cod e data to identify the sc anner as a Metrolog ic Scanner. ³ 1 05502 The scanner will not transmit the man ufacturer identi fication st ring.
Prefixes/Suffixes E 13 S ECTION E S TANDARD P REFIX C HARACTERS Enable Tab Prefix * Disable Tab Prefix ³ 1 16611 The scanner will tr ansmit a TAB (ASCII 09H) before each bar code.
Prefixes/Suffixes E 14 S ECTION E S TANDARD S UFFIX C HARACTERS * Enable CR Suffix Disable CR Suffix ³ 1 16613 The scanner will tr ansmit a C arriage R eturn after each bar code. ³ 1 16603 The scanner will not transmit a C arriag e R eturn after each bar code.
Prefixes/Suffixes E 15 S ECTION E S TANDARD S UFFIX C HARACTERS Enable ETX Suffix * Disable ETX Suffix ³ 1 16614 The scanner will tr ansmit E nd of T e X t (ASCII 03H) after the bar code data. ³ 1 16604 The scanner will not transmit E nd of T e X t (ASCII 03H).
Prefixes/Suffixes E 16 S ECTION E L ONGITUDINAL R EDUNDANC Y C HECK (LRC) Enable Transmit o f LRC Calculation * Disable Trans mit of LCR Calculation ³ 1 07811 The scanner outp uts an LRC check character af ter the bar code. ³ 1 07801 The scanner will not o utput an LRC (check character) after the bar code.
Prefixes/Suffixes E 17 S ECTION E C ONFIGURABLE S UFFIXES , A LL D ATA Scan the Enter/Exit Configuration Mode bar code before trying to set this feature. Refer to the Multi-Code Method on page xii. Enter/Exit Configuration Mod e ~ Configurable Suffix Character #1 ³ 9 99999 ³ 9 04500 A suffix ID can be added and assigned f or data transmission.
Prefixes/Suffixes E 18 S ECTION E C ONFIGURABLE S UFFIXES , A LL D ATA ~ Configurable Suffix Character #4 † ~ Configurable Suffix Character #5 † ³ 9 04800 Assigns a 4 th confi gurable suffix character.
Prefixes/Suffixes E 19 S ECTION E C ONFIGURABLE S UFFIXES , A LL D ATA ~ Configurable Suffix Character #8 † ~ Configurable Suffix Character #9 † ³ 9 05200 Assigns a 8 th confi gurable suffix character. ³ 9 05300 Assigns a 9 th confi gurable suffix character.
Prefixes/Suffixes E 20 S ECTION E S PECIAL F ORMATS Enable SINEKO Mode * Disable SINEKO Mode ³ 1 07914 ³ 1 07904 Enable Newcode Forma tting Mode A * Disable N ewcode Formatting M ode A ³ 1 16711 ³.
Prefixes/Suffixes E 21 S ECTION E C HARACTER R EPLACEMENTS To replace a character: 1. Scan the Enter/Exit Configura tion Mode bar code (located on page xii, at t he front of this guide).
.
Code Formatting F 1 S ECTION F UPC/EAN * Transmit UPC-A Check Digit Do not Transmit UPC-A Check Digit ³ 1 07517 ³ 1 07507 Transmit UPC-E Check Digit * Do Not Transmit UPC-E Check Digit ³ 1 07516 ³ 1 07506 Expand UPC-E to 12 Digits * Do Not Expa nd UPC-E To 12 Digits ³ 1 07515 Expand UPC-E bar codes to the 12 digit equivalent , UPC-A bar codes.
Code Formatting F 2 S ECTION F UPC/EAN Convert UPC-A to EAN-13 * Do Not Convert UPC-A to EAN-13 ³ 1 07514 The scanner conv erts UPC-A to EAN-13 by transmitting a le ading zero before the bar c ode. ³ 1 07504 The scanner will not c onvert UPC-A to EAN-13.
Code Formatting F 3 S ECTION F UPC/EAN * Transmit UPC-A Number System Do Not Transmit UPC-A Number System ³ 1 07511 ³ 1 07501 Metrologic strongly discourages using this feature.
Code Formatting F 4 S ECTION F UPC/EAN * Transmit EAN-8 Check Digit Do Not Transmit EAN-8 Check Digit ³ 1 07910 ³ 1 07900 * Transmit EAN-13 Check Digit Do Not Transmit EAN-13 Check Digit ³ 1 07912 ³ 1 07902 GTIN-14 Format No GTIN-14 Format ³ 1 07510 This feature is n ot available with al l models.
Code Formatting F 5 S ECTION F C ODABAR Transmit Codabar Start/Stop Characters * Do Not Transmit Codabar Start/Stop ³ 1 07717 Transmits Codabar’s start/stop characters before and after each bar code. ³ 1 07707 Will not transmit Codabar’s start/stop characte rs before and after each bar code.
Code Formatting F 6 S ECTION F C ODABAR Enable CLSI Editing ³ 1 07716 CLSI type editing will be done before the inf ormation is transmitted to the host.
Code Formatting F 7 S ECTION F C ODE 39 Enable MOD 43 Check on Code 39 * Disable MOD 43 Check on Code 39 ³ 1 00213 The scanner will o nly scan Code 39 bar codes that have a valid M odulo 43 Check Digit. ³ 1 00203 The scanner will not tes t Code 39 bar code s for a Modulo 43 Check Digit.
Code Formatting F 8 S ECTION F C ODE 39 Transmit Code 39 Start/St op Characters ³ 1 07710 The scanner trans mits Code 39’s start/stop cha racters before and after each bar c ode. * Do Not Transmit Code 39 Start/Stop Characters ³ 1 07700 The scanner will not tra nsmit Code 39’s start/s top characters before and aft er each bar code.
Code Formatting F 9 S ECTION F C ODE 11 A ND T ELEPEN Transmit Code 11 Check Digit * Do Not Transmit Code 11 Check Digit ³ 1 07713 The scanner will tr ansmit Code 11 check characters when used with th e Enable Code 11 feature in Section A. ³ 1 07703 The scanner will not transmit Code 11 check characters.
Code Formatting F 10 S ECTION F P LESSEY Transmit UK Plessey Check Dig it * Do Not Transmit UK Plessey Check Dig it ³ 1 07816 The scanner will tr ansmit UK Plessey Check Dig it characters when us ed with the Enable UK Ples sey feature in Section A. ³ 1 07806 Will not transmit UK Plessey Check Digit chara cters.
Code Formatting F 11 S ECTION F P LESSEY * No MSI Plessey Check Digit ³ 2 00704 The scanner will not tes t MSI Plessey bar codes for a check digit. Enable MSI Plessey M OD 10/10 Check Digit * Enable MSI Plessey MOD 10 Check Digit ³ 2 00734 The scanner will t est MSI Plessey bar co des for a double Modulo 10 chec k digit.
Code Formatting F 12 S ECTION F 2 OF 5 Enable Mod 10 Check on ITF * Disable MOD 10 Check on ITF ³ 1 00310 The scanner will o nly scan Interleaved 2 of 5 (ITF) bar codes that hav e a Modulo 10 check digit. ³ 1 00300 The scanner will not tes t Interleaved 2 of 5 (ITF) bar codes for a Modu lo 10 check digit.
RS-232 G 1 S ECTION G E NABLE RS-232 M ODE * Enable RS-232 Mode ³ 4 15554 When enabled the scanner will work with RS-232 ±12V serial output..
RS-232 G 2 S ECTION G P ARITY F EA TURES No Parity A parity bit is an extra data bit used to help catch data transmission errors. The scanner’s parity must match the host’s parity. ³ 3 16045 Odd Parity * Space Parity ³ 3 16005 Select Odd Parity to set the parity bit to either 1 or 0 to ensure an odd number of bits are 1’s.
RS-232 G 3 S ECTION G B AUD R AT ES 115200 BAUD Rate A “Baud” or “Baud Rate” is the speed at which data is transmitted. Select a Baud for the scanner that matches the host device.
RS-232 G 4 S ECTION G B AUD R AT ES * 9600 BAUD Rate 4800 BAUD Rate ³ 4 15850 ³ 4 15840 2400 BAUD Rate 120 0 BAUD Rate ³ 4 15830 ³ 4 15820 600 BAUD Rate 300 BAUD Rate ³ 4 15810 ³ 4 15800.
RS-232 G 5 S ECTION G D ATA /S TOP B ITS * 7 Data Bits 8 Data Bits ³ 1 16003 Number of data b its transmitted for eac h character. ³ 1 16013 1 Stop Bit * 2 Stop Bits ³ 1 16014 ³ 1 16004.
RS-232 G 6 S ECTION G H ARDWARE H ANDSHAKING Enable RTS/CTS Handshaking * Disable RTS/CTS Handshaking ³ 1 15816 O utput a R equest to S end (RTS) signal and wait f or a C lear T o S end (CTS) signal before transmit ting data. ³ 1 15806 Do not use RTS/CTS handshaking.
RS-232 G 7 S ECTION G H ARDWA RE H ANDSHAK ING Invert CTS Polarity (RSV2) * Standard CTS Polarity ³ 1 24511 +12V = Inactive, do no t send -12V = Active, OK to send ³ 1 24501 -12V = Inactive, do no t.
RS-232 G 8 S ECTION G H ARDWA RE H ANDSHAK ING CTS Scan Transmit * No CTS Scan Tr ansmit ³ 1 20417 The CTS line is us ed to allow a decoded bar code to be transmitted. Use r eserved code 4 to ensure 1 bar code per CTS. This will prev ent the scanner from gathering data until the CTS sign al has been retracted.
RS-232 G 9 S ECTION G S OFTWARE H ANDSHAKIN G Enable XON/XOFF Handshaking * Disable XON/XOFF Handshaking ³ 1 15914 The scanner will st op transmission when ever an XOFF (ASCII 13H) is received. Transmi ssion will resume after an XON (ASCII 11H) is received.
RS-232 G 10 S ECTION G S OFTWARE H ANDSHAKIN G Enable O/N Handshaking Disable O/N Handshaking ³ 1 15912 ACK/NAK handshaking (page G 9) must be en abled for this feature to work. ³ 1 15902 Support BEL/CAN in ACK/NAK * Ignore BEL/CAN in ACK/NAK ³ 1 15911 When BEL (07H) is rec eived, the scanner bee ps 3 times and exits the comm unications loo p.
RS-232 G 11 S ECTION G S OFTWARE H ANDSHAKIN G Enable XON/XOFF Scan Inhibit On * Dis able XON/XOFF Scan Inhibit Off ³ 1 16011 This feature is n ot available with al l models.
RS-232 G 12 S ECTION G M ISCELLANEOUS Enable French PC Term * Disable French P C Term ³ 1 16110 The scanner trans mits PC type make/break s can codes instead of ASCII data characters. The s can codes match a WYSE French PC Terminal Emulatio n. ³ 1 16100 Do not transmit in French PC Term Mode.
Keyboard H 1 S ECTION H E NABLE K EYBOARD E MULATION Load Keyboard W edge Defaults ³ 9 99994 Loads default s ettings for keyboard wedge mod e. Enable Stand-Alone Key board Emulation * Enable Keyboar d Wedge Emulation ³ 5155153 Use this with speci al stand- alone models that are not cabled for an external keyboard.
Keyboard H 2 S ECTION H C OUNTRY /S CAN C ODE T ABLE S ELECTS * USA Keyboard Switzerland Keybo ard ³ 4 16260 Enable USA Keyboard. ³ 4 16280 Enable Swiss Keyboar d Spain Keyboard Italy Keyboard ³ 4 .
Keyboard H 3 S ECTION H C OUNTRY /S CAN C ODE T ABLE S ELECTS UK Keyboard Belgium Keyboard ³ 4 16210 Enable UK Keyboard. ³ 4 16200 Enable Belgium K eyboard Japanese Keybo ard IBM 4700 Financial Keyb.
Keyboard H 4 S ECTION H K EYBOARD /S YS TEM T YPE * AT Keyboard XT Keyboard ³ 2 16215 If using an AT comput er, scan the above bar code. (Includes IBM PS/2 an d compatible mod els 50, 55, 60, 80) ³ 2 16205 If using an XT comput er, scan the above bar code.
Keyboard H 5 S ECTION H S PECIAL K EYBOARD F EATURES Transmit Make Code Only * Transmit Make/Break Code ³ 1 16311 Do not scan unless instructed by a Metrologic representative.
Keyboard H 6 S ECTION H S PECIAL K EYBOARD F EATURES Enable Alt Mode * Disable Alt Mode ³ 1 16217 The scanner will d uplicate the following key board sequence: Hold down ALT key and Type decimal n umber that corresponds to the appropriate chara cter.
Keyboard H 7 S ECTION H S PECIAL K EYBOARD F EATURES Enable Caps Lock (XT) * Disable Caps Lock (XT) ³ 1 16214 ³ 1 16204 The Caps Lock feature is not supported. Send Numbers as Keypad Data * Send Numbers as Normal Data ³ 1 16316 All data is sent as if it has been entered on a keypad.
Keyboard H 8 S ECTION H S PECIAL K EYBOARD F EATURES * Use Extended ASCII to Send Extended Key Codes Use Extended ASCII Characters as Extend ed ASCII ³ 1 16303 Use extended ASCII characters to send PC keyboard keys s uch as F1, F2, etc…See section M for details.
Keyboard H 9 S ECTION H I NTER -S CAN C ODE D ELAYS Inter-Scan Code Delay 800 Microseconds Inter-Scan Cod e Delay 7.5 msec ³ 8 16580 The time specifi ed represents the amount of tim e between individual 9 bi t-scan codes. This parameter m ay need to be adjus ted for operation with certain PC keyboard BIOS.
Keyboard H 10 S ECTION H C ONTROL S ETS In general, standard bar code symbologies will only encode the ASCII character set. Function keys, arrow keys and many other “extended” keys on an IBM compatible keyboard do not translate to ASCII characters.
Keyboard H 11 S ECTION H C ONTROL S ET #1 ASCII (HEX) ASCII Control Extended Ke y 00H Null Numeric Keypad 01H SOH Num Lock 02H STX Down 03H ETX Numeric Keypad 04H EOT Insert 05H ENQ Delete 06H ACK Sys.
Keyboard H 12 S ECTION H 3151 T ERMINAL K EYBOARD * 3151 Terminal K eyboard ³ 3 16400.
OCIA I 1 S ECTION I OCIA Load OCIA Defaults Enable OCIA ³ 9 99993 ³ 4 15544 Select this option if communications require OCIA ( O ptically C oupled I nterface A dapter).
.
Light Pen/Laser Emulation J 1 S ECTION J L IGHT P EN Enable Light Pen Mode ³ 4 15524 Select this option if the scanner will be us ed in place of a light pen.
Light Pen/Laser Emulation J 2 S ECTION J L IGHT P EN /S ET N ARROW E LEMENT B ORDER Poll Light Pen S ource * Do Not Poll Light Pen S ource ³ 1 16915 The scanner waits for a n active source volt age before transmitting data. ³ 1 16905 The scanner will not wai t for an active source v oltage before transmit ting data.
Light Pen/Laser Emulation J 3 S ECTION J S ET N ARROW E LEMENT W IDTH /L ASER E MULATION * 1 ms Narrow Element Width 60 µs Narrow Element Width ³ 81681630 This option allows the transmission of Light/Pen Wand emulation a 1 ms narrow element width. ³ 8168100 This transmits at 60 µs narrow element width.
.
IBM 46xx Configuration K 1 S ECTION K IBM 46 XX C ONFIGUR ATION /IBM P ORTS Load IBM 46xx Defaults Enable IBM 46xx Communication ³ 9 99995 Load default form at settings for IBM 46xx systems. ³ 4 15504 Select this option for IBM 46xx SIOC/RS485 communication.
IBM 46xx Configuration K 2 S ECTION K IBM R ESER VE C ODES IBM Reserve #1 IBM Reserve # 2 ³ 3 17200 ³ 3 17210 IBM Reserve #3 ³ 3 17220 IBM Reserve #5 ³ 3 17240.
Code Bytes M 1 S ECTION M C ODE B YT E U SAGE User configurable prefixes, symbol length and other features that use these code bytes for configuration, require that the scanner be in configuration mode. Scan the Enter/Exit Configuration Mode bar code before starting t he configuration cycle.
Code Bytes M 2 S ECTION M C ODE B YTE S 0-5 Code Byte 0 Code Byte 1 ³0 ³1 Code Byte 2 Code Byte 3 ³2 ³3 Code Byte 4 Code Byte 5 ³4 ³5.
Code Bytes M 3 S ECTION M C ODE B YTE S 6-9 Code Byte 6 Code Byte 7 ³6 ³7 Code Byte 8 Code Byte 9 ³8 ³9.
Code Bytes M 4 S ECTION M R ESERVED C ODES ~ Enable Reserved Code ³ 9 99988 Contact a Metrolo gic customer s ervice representative for additional deta ils on this feature.
Code Bytes M 5 S ECTION M C ODE B YTE /C ODE T YPE T ABLE C ODE B YTE C ODE T YPES 004 UPC-A 002 UPC-E 003 EAN-8 005 EAN-13 080 Code 39 081 Codabar 082 Interleaved 2 of 5 083 Code 128 084 Code 93 091 .
Code Bytes M 6 S ECTION M ASCII R EF ERENCE T ABLE HEX V ALUE D ECIMAL V ALUE / C ODE B YTE V ALUE C HARACTER C ONTROL K EYBOARD E QUIVALENT 00 000 NUL @ 01 001 SOH A 02 002 STX B 03 003 ETX C 04 004 .
Code Bytes M 7 S ECTION M ASCII R EF ERENCE T ABLE HEX V ALUE D ECIMAL V ALUE / C ODE B YTE V ALUE C HARACTER C ONTROL K EYBOARD E QUIVALENT 1B 027 ESC [ 1C 028 FS 1D 029 GS ^ 1E 030 RS _ 1F 031 US 2.
Code Bytes M 8 S ECTION M ASCII R EF ERENCE T ABLE HEX V ALUE D ECIMAL V ALUE / C ODE B YTE V ALUE C HARACTER C ONTROL K EYBOARD E QUIVALENT 36 054 6 37 055 7 38 056 8 39 057 9 3A 058 : 3B 059 ; 3C 06.
Code Bytes M 9 S ECTION M ASCII R EF ERENCE T ABLE HEX V ALUE D ECIMAL V ALUE / C ODE B YTE V ALUE C HARACTER C ONTROL K EYBOARD E QUIVALENT 4F 079 O letter O 50 080 P 51 081 Q 52 082 R 53 083 S 54 08.
Code Bytes M 10 S ECTION M ASCII R EF ERENCE T ABLE HEX V ALUE D ECIMAL V ALUE / C ODE B YTE V ALUE C HARACTER C ONTROL K EYBOARD E QUIVALENT 6A 106 j 6B 107 k 6C 108 l 6D 109 m 6E 110 n 6F 111 o 70 1.
Code Bytes M 11 S ECTION M E XTEND ED K EY C ODE R E FERENCE T ABLE K EY A T S CAN C ODE PS2 S CAN C ODE 3151 P REFIX /S UFFIX V ALUE H EX = D ECIMAL 75H 48H 63H 80H = 128 72H 50H 60H 81H = 12.
Code Bytes M 12 S ECTION M E XTEND ED K EY C ODE R E FERENCE T ABLE K EY A T S CAN C ODE PS2 S CAN C ODE 3151 P REFIX /S UFFIX V ALUE H EX = D ECIMAL Numeric - 7BH 4AH 7CH 9DH = 157 Numeric * 7CH 37H .
Miscellaneous Features N 1 S ECTION N C USTOM D EFAULTS Metrologic manufactures several scanners for OEM applications. These scanners may use a different set of defaults than the standard Metrologic factory defaults. Scanning the following bar codes will restore the default factory settings.
Miscellaneous Features N 2 S ECTION N C USTOM D EFAULTS Ruby Verifone Defaults RCH ³ 84661280 Scan this code f ollowed by the “Recall Defau lts” code to enable and loa d Ruby Verifone Defaults. ³ 8 46610 Scan this code f ollowed by the “Recall Defaults ” code to enable and load RCH Defaults.
Miscellaneous Features N 3 S ECTION N C USTOM D EFAULTS German Post Defaults Wincor Nixdorf Defaul ts ³ 84660090 Scan this code f ollowed by the “Recall Defau lts” code to enable and loa d German Post Defaults. ³ 84 660140 Scan this code f ollowed by the “Recall Defau lts” code to enable and loa d Wincor Nixdorf Defaults.
Miscellaneous Features N 4 S ECTION N C USTOM D EFAULTS Custom 21 Default s Cus tom 22 Defaults ³ 84660210 Scan this code f ollowed by the “Recall Defau lts” code to enable and loa d Custom 21 Defaults. ³ 84 660220 Scan this code f ollowed by the “Recall Defau lts” code to enable and loa d Custom 22 Defaults.
Miscellaneous Features N 5 S ECTION N S ERIAL C ONFIGUR ATION M ODE For Serial Configuratio n Mode, all comma nds must be f ramed by an STX (02 Hex ) and ETX (03 Hex). To recall defaults: 1. Transmit <STX>9999 99<ETX> through the Seri al Port.
.
Auxiliary Port Controls O 1 S ECTION O D ISABLE A UXILIARY P ORT * Disable AUX Port ³ 4 37300 AUX P ORT AND S ECONDARY D EVIC E D ATA F ORMATS The following se ction includes features that are not available with all Metrologic scanner models. Please contact a customer service representative for additional information and technical assistance.
Auxiliary Port Controls O 2 S ECTION O AUX P ORT AND S ECONDARY D EVIC E D ATA F ORMATS Step 2 : Then scan the following bar codes, in order, to configure the secondary scanner. 1. Enable AUX Output 2. Secondary Scanner Data Format ³ 1 24817 ³ 4 37530 3.
Auxiliary Port Controls O 3 S ECTION O AUX P ORT AND S ECONDARY D EVIC E D ATA F ORMATS The following se ction includes features that are not available with all Metrologic scanner models. Please contact a customer service representative for additional information and technical assistance.
Auxiliary Port Controls O 4 S ECTION O A DDITIONAL A UXILIARY P ORT D ATA F ORMATS The auxiliary input port’s data format must match the main output format of the secondary device.
Auxiliary Port Controls O 5 S ECTION O A DDITIONAL A UXILIARY P ORT D ATA F ORMATS Enable AUX Port with Stratos Decode Data Format ³ 4 37320 A UXILIARY P ORT B AUD R ATES AUX 115200 Baud Rate AUX 576.
Auxiliary Port Controls O 6 S ECTION O A UXILIARY P ORT B AUD R ATES AUX 14400 Baud Rate AUX 9600 Baud Rate ³ 4 37060 ³ 4 37050 AUX 4800 Baud Rate AUX 2400 Ba ud Rate ³ 4 37040 ³ 4 37030 AUX 1200 .
Auxiliary Port Controls O 7 S ECTION O A UXILIARY P ORT B AUD R ATES AUX 300 Baud Rate ³ 4 37000 A UXILIARY P ORT P ARITY AUX No Parity ³ 3 37245 AUX Mark Parity * AUX Space Parity ³ 3 37235 ³ 3 3.
Auxiliary Port Controls O 8 S ECTION O A UXILIARY P ORT P ARITY AUX Even Parity AUX Odd Parity ³ 3 37225 ³ 3 37205 A UXILIARY P ORT S TOP B ITS /D ATA B ITS AUX 1 Stop Bit * AUX 2 Stop Bits ³ 1 372.
Auxiliary Port Controls O 9 S ECTION O A UXILIARY RTS/CT S AND M ODE 7 * Enable AUX RTS/CTS Handshaking Disable AUX RTS/CTS Handshaking ³ 1 37016 ³ 1 37006 Message AUX RTS/CTS * Character AUX R TS/C.
Auxiliary Port Controls O 10 S ECTION O A UXILIARY D/E, F/L, AND M/O Enable AUX “D/E” Commands * Disable AUX “D/E” Commands ³ 1 37117 ³ 1 37107 Enable AUX “F/L” Commands * Disable AUX .
Auxiliary Port Controls O 11 S ECTION O A UXILIARY XON/XOFF AND ACK/ NAK * Enable AUX XON/ XOFF Handshaking Disable AUX XON/XOFF Handshaking ³ 1 37114 ³ 1 37104 * Enable AUX ACK/NAK Commands Disable.
Auxiliary Port Controls O 12 S ECTION O A UXILIARY CTS AND RTS P OLARITY * Normal AUX CTS Polarity Flip AUX CTS Polarity ³ 1 37307 ³ 1 37317 * Normal AUX RTS Polarity Flip AUX RTS Polarity ³ 1 3730.
Auxiliary Port Controls O 13 S ECTION O M AIN O UTPUT P ORT A UXILIARY D ATA F ORMATS When a scanner is used as a secondary scanner to another scanner’s auxiliary input, the output data can be in one of the following formats.
Auxiliary Port Controls O 14 S ECTION O M AIN O UTPUT P ORT A UXILIARY D ATA F ORMATS TECH 7 & 8 Output AUX Data Format Reserved 1 Output AUX Data Format ³ 4 37560 ³ 4 37590 Reserved 2 Output AU.
Auxiliary Port Controls O 15 S ECTION O I NTER -C HARACTER D ELAYS No AUX Port Inter-Character Delays * 1 msec AUX Port Inter-Character Delay ³ 8 37600 ³ 8 37610 10 msec AUX Port Inter-Character Del.
Auxiliary Port Controls O 16 S ECTION O A UXILIARY P ORT C ONTROLS Prevent Beep From AUX * Allow Beep from A UX ³ 8 37600 Prevent the main scanner from beeping whe n the barcode comes fr om the AUX port. This is the opposite of not beeping the AUX and letting t he main scanner beep as v erification of the barcode sen t.
USB P 1 S ECTION P USB Enable Full Speed USB ³ 4155124 Load Integrate d Full Speed USB IBM/OEM Defaults ³ 9 99970.
USB P 2 S ECTION P USB The following cod es can be used if the Loa d Integrated Full Spee d USB IBM/OEM Defaults bar code has not been scanned. Enable USB IBM ID * Disable USB IBM ID ³ 1 17817 ³ 1 1.
USB P 3 S ECTION P USB The following cod es can be used if the Loa d Integrated Full Spee d USB IBM/OEM Defaults bar code has not been scanned. IBM OEM Scanner 4A00h Flatbed IBM OEM Scanner 4B00h Handheld ³ 3 16410 Full speed USB only. ³ 3 16430 Full speed USB only.
USB P 4 S ECTION P USB Enable Low Speed USB Enable Low Speed USB POS Defaults ³ 4155 114 ³ 84 660180 Load Low Spee d External USB Defaults Load L ow Speed Internal USB Keyboard Defaults ³ 9 99978 ³ 9 99941 For units labeled Low Speed (LS) USB. Load Full Speed K eyboard Internal USB Defaults ³ 9 99940 For units labeled Full Speed (FS) USB.
IS3480 / MS3580 / MS3780 R 1 S ECTION R IS3480 / MS3580 / MS3780 The following bar codes are spec ific to the IS 3480, MS358 0 and the MS3780 unless oth erwise noted.
IS3480 / MS3580 / MS3780 R 2 S ECTION R IS3480 / MS3580 / MS3780 The following bar codes are spec ific to the IS 3480, MS358 0 and the MS3 780 (in-stand) unless otherwise noted.
IS3480 / MS3580 / MS3780 R 3 S ECTION R MS3780 The following bar codes are spec ific to the MS37 80 (out-of-stan d) unless otherwis e noted. Primary Scan Patterns Secondary Scan Patterns * Primary Omni, Out-of-Stand Secondary Omni, Out-of-Sta nd ³ 9 99937 This bar code se ts the primary pattern to all scan lines on for omn idirectional reading.
IS3480 / MS3580 / MS3780 R 4 S ECTION R IS3480 / MS3580 / MS3780 The following bar codes are spec ific to the IS 3480, MS358 0 and the MS3780 unless oth erwise noted. Sweet Spot Mode Enable Sweet Spot Mo de ³ 9 98048 This feature is n ot available with th e MS3580 or the MS3780.
IS3480 / MS3580 / MS3780 R 5 S ECTION R IS3480 / MS3580 / MS3780 The following bar codes are spec ific to the IS 3480, MS358 0 and the MS3780 unless oth erwise noted. IR Activation IR Activation * Disable IR Activation ³ 1 23817 ³ 1 23807 TTL RS232 The following bar codes are only valid for the TTL RS 232 Quantum seri es (IS/MS3x80- 102 ).
IS3480 / MS3580 / MS3780 R 6 S ECTION R MS3780 The following bar codes are spec ific to the MS 3780 unless otherwise noted. CodeGate (MS3780) * Enable CodeGate Out-of-Stand, Primary Pattern Active Dis.
IS3480 / MS3580 / MS3780 R 7 S ECTION R MS3780 The following bar codes are spec ific to the MS 3780 unless otherwise noted. Modes (MS3780) Enable Normal Mo de ³ 4 18304 Enable IR Activation Mode ³ 4.
.
Protocol Formatting S 1 S ECTION S P ROTOCOL F ORMATTING The following barcodes may be used for the Stratos Series and some Fusion or Voyager models. Please contact a customer service representative for additional information and technical assistance.
Protocol Formatting S 2 S ECTION S P ROTOCOL F ORMATTING ROM Emulation Version 7 ROM Emulati on Version 8 ³ 3 42160 ³ 3 42170.
.
.
.
April 2007 Printed in the USA 00 - 02407 H.
Een belangrijk punt na aankoop van elk apparaat Honeywell IS3480 QuantumE (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Honeywell IS3480 QuantumE heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Honeywell IS3480 QuantumE vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Honeywell IS3480 QuantumE leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Honeywell IS3480 QuantumE krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Honeywell IS3480 QuantumE bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Honeywell IS3480 QuantumE kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Honeywell IS3480 QuantumE . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
