Gebruiksaanwijzing /service van het product 40120 van de fabrikant Hunter Fan
Ga naar pagina of 28
1 Electronic/Mechanical Thermostat Model 40120 installation and operation manual 44018-01 04-01-2008.
2 For assistance with wiring or operation, our T echnical Support Group is available from 8 am to 5 pm CST . they may be reached toll-free at 1-888-830-1326.
3 T able of Contents Important Information ....................................... 5 T ools ................................................................. 6 Uninstalling the Existing Unit ............................ 9 Installing the Thermostat ...
4 Congratulations! Thank you for choosing a Hunter thermostat. Y our new Hunter thermostat will provide years of reliable service and year-round energy savings. Please read this manual before beginning installation and save this booklet for complete operation instructions.
5 This thermostat is designed to work on the following heating and cooling systems: Gas – Standing Pilot Gas – Electronic Ignition Gas – Fired Boilers Gas – Millivolt Systems Oil – Fired Boilers Oil – Fired Furnace Electric Furnace This thermostat is not designed for heat pump systems or 1 10/220 V baseboard heating systems.
6 This thermostat includes two #8 slotted screws and two wall anchors for mounting. T o install your new thermostat, you will need the following supplies: Flat-head screwdriver ..........................................................................
7 NOTICE! Do not disconnect the wires from the existing thermostat before reading these instructions. The wires must be labeled prior to removal to ensure proper reconnection.
8 Y RC G W Y RC G W.
9 1. T urn the system power OFF from the existing thermostat. T urn the power to the HV AC system OFF at the main power panel or at the furnace. 2. Remove the existing thermostat cover to access the wires from the wall. (Some thermostats may have multiple covers, screws or other locking devices that must be removed or disengaged.
10 If your existing thermostat is marked... label the wire with this sticker: RH / R / VR / 4 RH RH 24 V olt W / H W W heating G / F G G fan * See page 27 for complete wiring diagram.
11 4. Using the provided stickers, label each wire according to the chart. (If the terminals are not labeled, contact a qualied HV AC technician.) Note: Wire colors do not always comply with standards, so wire color should be ignored. Refer to the existing terminal designation for proper identication.
12 INST ALLING THE THERMOST A T INST ALLING THE THERMOST A T 1. Remove the new thermostat from the back plate by pulling the two halves apart. Thermostat W all Plate.
13 W RH G.
14 2. Position the new wall plate on the wall and pull the labeled wires through the opening. 3. If the existing holes do not match those on the Hunter wall plate, or if there are no existing holes, level the wall plate and mark the wall for two holes.
15 RH G W.
16 INST ALLING THE THERMOST A T , CONT . CONNECTING THE WIRES 1. Loosen, but do not remove, the terminal screws. 2. Match and connect the wires from the wall to the terminals as shown. Wires should be inserted behind the black terminal shields. T ighten each screw after the connection has been made.
17 HE/HG Switch HG HE.
18 A TT ACHING THE THERMOST A T 4. Locate the HE/HG s w i t c H on the back of the thermostat. Set the switch to HG for a gas furnace or oil burner . Set the switch to HE for electric furnaces. 5. Insert two fresh AA alkaline batteries. 6. Align the thermostat with the the wall plate, and snap the two halves together .
19.
20 Fan Switch System Switch Set T emperature Slider Thermometer Battery Indicator SY STEM OFF HE A T AU T O ON 3 0 2 0 1 0 9 0 8 0 7 0 6 0 5 0 F C 9 0 8 0 7 0 6 0 5 0 F.
21 OPERA TION 1. Set the s E t t E m p E r a t u r E s l i d E r to the desired temperature. 2. The s y s t E m s w i t c H determines the operating mode of the thermostat. Select O f f or H E a t . 3. The f a n s w i t c H should normally be located in the a u t O position.
22 INDICA T ORS AND ADUSTMENT 1. The t H E r m O m E t E r indicates the room temperature. 2. The B a t t E r y i n d i c a t O r displays two stages of w E a k B a t t E r y w a r n i n G , indicated by the B a t t E r y i n d i c a t O r ashing once approximately every second.
23 Span Adjust SP AN.
24 INDICA T ORS AND ADJUSTMENTS, CONT . 1. Remove the thermostat from the wall plate. 2. T o make your system run LONGER, turn the s p a n a d j u s t clockwise. 3. T o make your system run SHORTER, turn the s p a n a d j u s t counter clockwise. 4. Reattach the thermostat to the wall plate.
25 1. My heating or cooling will not turn on or off. 1 a. Check the HE/HG switch to ensure it is set to the correct position. 1 b. Check the circuit breakers and switches to ensure there is enough power to the system. 1 c. Replace the batteries with fresh AA alkaline batteries.
26 Is there help on the web? Y es. Visit http://www .hunterfan.com for more information. .................................................................................... ......... Can’t I just call someone? Sure. Our T echnical Support Group is available from 8 am to 5 pm CST .
27 WIRING DIAGRAMS Rh W Heat 24V or Millivolt Supply Heat Rela y or V alve 2-wire Heat Only System G Rh W Heat 24V Supply Heat Rela y or V alve 3-wire Heat Only System Fan Relay.
28 © 2007 Hunter Fan Company.
Een belangrijk punt na aankoop van elk apparaat Hunter Fan 40120 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Hunter Fan 40120 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Hunter Fan 40120 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Hunter Fan 40120 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Hunter Fan 40120 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Hunter Fan 40120 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Hunter Fan 40120 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Hunter Fan 40120 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
