Gebruiksaanwijzing /service van het product 13524SB-XLS van de fabrikant Husqvarna
Ga naar pagina of 25
13524SB - XLS 13524SB - XLS Owner's Manual / 96193004800 / 2009-07.
2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces.
3 CONGRA TUL A TIONS on your purchase of a new snow thrower . It has been designed, engineered and man u fac - tured to give best possible dependability and per for mance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center .
4 P ARTS P ACKED SEP ARA TEL Y IN CARTON (1) POWER CORD (198563) (1) DISCHARGE CHUTE (6) SHEAR BOL TS 1/4-20 x 1-3/4 (192090) (1) WASHER 3/8 (19131316) (1) L OCKNUT 5/16-18 (751153) (1) CARRIAGE BOL T.
5 AS SEMBL Y / PRE-OPERA TION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product.
6 AS SEMBL Y / PRE-OPERA TION AUGER CONTROL LEVER AUGER CONTROL ROD AUGER CONTROL BRACKET RET AINER SPRING FIG. 6 INST ALL AUGER CONTROL ROD (See Figs. 5 and 6) The auger control rod has the short loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.
7 AS SEMBL Y / PRE-OPERA TION INST ALL DISCHARGE CHUTE / CHUTE ROT A TER HEAD (See Fig. 7) NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head. 1. Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower .
8 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments.
9 OPERA TION Drive speed control lever - used to select forward or reverse motion and speed of snow thrower . T raction drive control lever - used to engage power - pro pelled for ward or reverse motion of snow thrower . LH and RH turn triggers - used to steer the snow thrower .
10 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just- ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles.
11 OPERA TION TO THROW SNOW (See Fig. 15) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow . • Release the auger control lever to stop throwing snow .
12 OPERA TION BEFORE ST ARTING THE ENGINE CHECK ENGINE OIL LEVEL (See Fig. 22) The engine on your snow thrower has been shipped, from the factory , already filled with oil.
13 OPERA TION ENGINE OIL FILL CAP / DIPSTICK FUEL SHUT - OFF VAL VE PRIM ER SAFETY IG NI TION KEY THROT TLE CHOKE CONTROL ST ARTER BUTTON RECOIL ST ARTER HANDLE GAS O LINE FILLER CAP NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL L OCA TION. ACTUAL L OCA TION MA Y VARY WITH ENGINE ON Y OUR UNIT .
14 SNOW THROWING TIPS • Always operate the snow thrower with the engine at full throttle. F ull throttle offers the best performance. • Go slower in deep, freezing or heavy wet snow . Use the drive speed control, NOT the throttle, to adjust speed.
15 MAINTENANCE LUBRICA TION CHART GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual.
16 MAINTENANCE BEL TS Check belts for deterioration and wear after every 50 hours of operation and replace if necessary . The belts are not ad just able. Replace belts if they begin to slip from wear . (See “TO REMOVE BEL T COVER” in the Service and Adjustments section of this manual).
17 SERVICE AND ADJUSTMENTS FRAME BEL T COVER SCREWS FIG. 24 SHEAR BOL TS (See Fig. 23) AUGER SHEAR BOL TS Both right and left-hand augers are secured to the auger shaft with a spacer , shear bolt and hex nut.
18 SERVICE AND ADJUSTMENTS 7. RELIEVE TENSION ON TRACTION DRIVE BEL T IDLER and remove traction drive belt from around pulleys. HINT : Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.
19 SERVICE AND ADJUSTMENTS AXLE KLIK PIN (INST ALL IN OUTER HOLE OF AXLE ONL Y) OUTER HOLE WHEEL HUB WHEEL FIG. 26 TO ADJUST CABLE TENSION (See Fig. 27) Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster .
20 STORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance.
21 Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Refill fuel tank with fresh, clean gasoline.
22 SERVICE NOTES.
23 SERVICE NOTES.
532 42 85-38 07.09.09 SR Printed in the U.S.A. SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from.
428482 07.01.09 SR Printed in U.S.A..
Een belangrijk punt na aankoop van elk apparaat Husqvarna 13524SB-XLS (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Husqvarna 13524SB-XLS heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Husqvarna 13524SB-XLS vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Husqvarna 13524SB-XLS leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Husqvarna 13524SB-XLS krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Husqvarna 13524SB-XLS bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Husqvarna 13524SB-XLS kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Husqvarna 13524SB-XLS . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
