Gebruiksaanwijzing /service van het product DS160C van de fabrikant Husqvarna
Ga naar pagina of 23
DS160C Manuel d’utilisation et d’entretien Manuale di Istruzioni Foreuse de chantier T rapanatrice da cantiere Manual de Instrucciones Operating Instructions T aladradora de obra Drilling Machine .
2.
W ARNING Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to cause cancer , birth defects or other reproductive harm.
PREF ACE TO THE MANUAL These operating instructions apply exclusively to drill stand, type DS 160 C. Please also read the operating instructions that accompany your drill motor to verify their compatibility and not to exceed the limitations of the DS 160 C drill stand.
·Prevent accidents due to unsuitable use, by an untrained person, during maintenance, repairs, overhauls, handling or transport ·Improve the reliability and durability of the machine ·Ensuring correct use, regular maintenance and rapid repair in order to reduce stoppage times and repair cost.
·Use of a diamond core bit for water lubricated cutting of concrete, asphalt, marble, stone, granite, brick and facings (porcelain, glazed tiles, ceramics, etc).
3. Assembly Align holes on the wheel assembly (1) with the tapped holes on rear of the base plate (2). Insert bolts (3) through lockwashers (4), then insert bolts through wheel assembly and screw onto base plate. 4. Description and Features of the Drill Stand T apered roller carriage.
The operator must wear protective clothing appropriate to the work he is doing. W e recommend that this includes both eye and ear protection. Any person not involved in the work should leave the working area. Use core bits which are suitable for the work to be done.
10. Designation of the Components Carrying Handle Feed Handle Back Support Carriage Level and Plum Indicator Carriage Brake Drill Motor Mount Gear Rack Depth and Angle Scale Angle Column Lock Screw Le.
11. Operation Positions The drill stand can be used for drilling ceilings, floors and walls. Individual safety instructions for each area of applications as described in the following chapters must be observed and complied with.
Drill a hole for the anchor at a distance of 292 mm ( X ) from the hole center . Drive the impact anchor and secure. Screw in the all thread rod (2). Slip on the base plate (4) over the thread rod. Fit the washer and tighten nut (1) slightly . Align the base plate (4) by means of the adjusting screw (3).
13. Setting the Angle of the Column Remove the column lock bolt (1) Loosen bolt on back support bracket (2). The column can now be pulled into the desired position, 0 to 45 degrees. Side decal provides approximate measurements. If greater precision is required use alternate measuring techniques.
16. Maintenance For details of maintenance work required for the drill motor , please refer to the enclosed motor manufacturer’ s documentation. Routine Checks Check electrical connections routinely before each use. The following routine checks should be carried out monthly: Check that all screws and fastening elements are properly secure.
Wear Cylinders Using a 4mm allen wrench, turn each of the 4 setscrews (4) clockwise until the nylatron wear cylinders (5) are in slight contact with the column. Side Cleaning Plates Loosen each of the 4 cleaning plate capscrews (6) using a 3mm allen wrench and slide the cleaning plate (7) so it is in contact with the column wear plates.
1 2 3 4 5 6 7 8 9 11 12 13 14 15 16 20 19 18 23 24 25 26 27 29 28 17 22 21 10 31 30 15.
I te m D e scri p ti o n Pa rt N u mb er Q ty Co mme n ts 1 M4x16 S ocket Head Cap sc rew 541404147 4 2 H andl e To p D ecal 541404097 1 3 Col u mn Hand l e 541404781 1 4 T- Washer 541404078 1 5 Angl .
1 2 3 4 5 6 * 7 * 8 1 0 9 11 12 13 5 1 5 1 6 1 7 18 19 18 16 20 21 22 23 14 * 6.1 6.2 6.3 6.4 6.5 *7.1 7.2 7.3 7.4 7.5 17.
I te m D e scri p ti o n Pa rt N u mb er Q ty Co mme n ts 1 D rill C a r ria g e 541404784 1 2 A daptor Plat e 541404029 1 3 D rill C o lla r 541404030 1 4 Key 541404031 1 5 M8x25 S ocket Head Cap sc rew 541404126 3 6 Locki ng Mec h ani sm 541404114 1 Compl et e 6.
1 2 3 4 5 6 7 8 9 10 11 I te m D e scri p ti o n Pa rt N u mb er Q ty Co mme n ts 1 Col u mn 541404050 1 2 M3x8 S ocket Head, Fl at Head Scr ew 541404137 24 3 D epth M easurem ent Decal 541404054 2 4 .
I te m D e scri p ti o n Pa rt N u mb e r Q ty Comme n ts 1 Roll er 541404037 1 2 Spacer 541404036 1 3 Bear i ng 12mm I. D .x 24mm O . D . x6mm 541404034 2 1 2 3 20.
I te m D e scri p ti o n Pa rt N u mb er Q ty Co mme n ts 1 Angl e Suppor t M ember 541404062 2 2 Angl e Suppor t S pacer 541404064 1 3 T- Washer Retai ner 541404065 1 4 M6x20 F l at Soc ket Head Scr .
1 2 3 4 5 I te m D e scri p ti o n P art Numb er Qty Co mme n ts 1 Knob w / St ud 541404073 1 2 1/ 8 N PT Mal e Fi t ti ng 541404071 1 3 Ball D etent 541404072 2 4 Vacuu m C ap 541404785 1 5 Vacuu m C.
HUSQV ARNA CONSTRUCTION PRODUCTS Product Limited W arranty Equipment manufactured by Husqvarna Construction Products is warranted to be free from defects in material and workmanship if operated proper.
Een belangrijk punt na aankoop van elk apparaat Husqvarna DS160C (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Husqvarna DS160C heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Husqvarna DS160C vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Husqvarna DS160C leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Husqvarna DS160C krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Husqvarna DS160C bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Husqvarna DS160C kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Husqvarna DS160C . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
