Gebruiksaanwijzing /service van het product SENG-3002-01 van de fabrikant IBM
Ga naar pagina of 30
iSeries 270 and 820 30xx Memory Card Installation V ersion 5 SENG-3002-01 .
.
iSeries 270 and 820 30xx Memory Card Installation V ersion 5 SENG-3002-01 .
Note Before using this information and the pr oduct it supports, be sure to r ead the “Safety and Environmental Notices” on page iii and the “Notices” on page 19. Second Edition (May 2001) This edition applies only to reduced instructions set computer (RISC) systems.
Safety and Environmental Notices Danger Notices A danger notice calls attention to a situation that is potentially lethal or extremely hazardous to people.
Product Recycling and Disposal Components of the system, such as structural parts and cir cuit cards, can be recycled wher e recycling facilities exist. IBM does not curr ently collect and recycle used IBM products fr om customers in the United States other than those products that are involved in trade-in pr ograms.
Installation Instructions Before you begin __ 1. T ake a minute to become familiar with these instructions. Note that you may not complete every step in this instruction. __ 2. These instructions contain steps on how to install memory (main storage cards) , including adding another 2884 card assembly , into the system unit.
__ 9. If you encounter difficulties during the installation, contact your authorized dealer or service provider . Powering off the system unit __ 1. Set the System performance adjustment to a value other than option 0 . __ a. On an iSeries command line, type WRKSYSVAL (QPFRADJ) and press Enter .
__ 1. Do you have a 270 system unit? Ye s N o ↓ Y ou have a 820 system unit. Go to step 5 on page 4. __ 2. Does your system unit have an access cover as shown in Figure 1 A ? Ye s N o ↓ The memory is located on the inside of your 270 system unit.
__ 5. Do you have a new 2884 card assembly to install in your 820 system unit? Ye s N o ↓ Go to step 7 on page 5. __ 6. Remove the empty card assembly C .
__ 7. Remove the 2884 card assembly B or C fr om the system unit by doing the following: __ a. Unlatch the two blue latches on the 2884 until the card assembly slightly “ pops ” out. __ b. Pull on both latches at the same time to remove the car d assembly from the system unit.
__ 2. Remove the blank filler cards fr om the next available positions by doing the following: __ a. Push outward on the latches A that ar e located at each end of the filler card, Figure 5 on page 7. __ b. Remove the filler card fr om the card socket and discar d it.
__ 6. Install the remaining memory car ds. __ 7. When you finish installing all the memory cards, turn the car d assembly over , and slide it into the system unit. Push on both card latches at the same time. Close the latches when you cannot push the card assembly any further into the system unit.
Figure 6. Memory Connectors View 1 8 30xx Memory Card Installation V5R1.
__ 2. Refer to the figure that matches your system unit to place the memory in the correct or der . __ 3. Place memory cards as follows on the pr ocessor: v In pairs, beginning with C and D , then E and F , and so on. v Each pair of storage cards must be either 128MB, 256MB, or 512MB.
__ 8. Install the second memory card. __ 9. Do you have any other adapter cards or devices to install? No Y es ↓ If you have another device such as an adapter card, a tape unit, or disk units to install, go to the instructions that came with that device.
__ 4. DANGER An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the system or the products that attach to the system. It is the customer ’ s responsibility to ensure that the outlet is correctly wired and grounded to prevent an electrical shock.
__ a. Press the Mode Select button until the Manual mode indicator (a small hand) lights up. __ b. Press the Incr ement/Decrement push button until 02 appears in the Function/Data display . __ c. Press the Enter push button on the contr ol panel. __ d.
Note: If the status is not Operational, check the memory cards. __ g. If you have a printer , print the configuration list. Note: T o print the hardware r esources list, pr ess F12 one time. When the Logical Hardware Resour ces menu appears, press F6 .
14 30xx Memory Card Installation V5R1.
Unit Covers Locate the diagram of the unit you are working on. If you have a 270 system unit in a rack, go to “ 270 unit in a rack ” on page 16. 270 and 820 System Units T o access the PCI card location, you need to remove the back cover and the side cover: __ 1.
270 unit in a rack 1. Press latches B and pull the server out using the handle C . 2. Refer to previous unit diagram to r emove the side cover .
System unit control panel Go to the front of your system unit. Open the contr ol panel door . Y our control panel looks like either Figure 9 or Figure 10 on page 18. Refer to the control panel for your unit. A Power On Light v A blinking light indicates power to the unit.
If your control panel looks like this, befor e you can use F Increment/Decr ement buttons and G Enter push button, you need to press H Mode Selects to select Manual mode N . A Power On Light v A blinking light indicates power to the unit.
Notices This information was developed for products and services of fered in the U.S.A. IBM may not offer the pr oducts, services, or features discussed in this document in other countries. Consult your local IBM repr esentative for information on the products and services curr ently available in your area.
T rademarks The following terms are trademarks of the IBM Corporation in the United States or other countries or both: AS/400 AS/400e series Client Access Client Access/400 IBM NetFinity Operating Sys.
Readers’ Comments — W e’d Like to Hear from Y ou iSeries 270 and 820 30xx Memory Card Installation V ersion 5 Publication No. SENG-3002-01 Overall, how satisfied are you with the information in .
Readers ’ Comments — We ’ d Like to Hear from Y ou SENG-3002-01 SENG-3002-01 Cut or Fold Along Line Cut or Fold Along Line Fold and T ape Please do not staple Fold and T ape Fold and T ape Please do not staple Fold and T ape NO POST AGE NECESSARY IF MAILED IN THE UNITED ST A TES BUSINESS REPL Y MAIL FIRST -CLASS MAIL PERMIT NO.
.
Printed in the United States of America on recycled paper containing 10% recovered post-consumer fiber . SENG-3002-01.
Een belangrijk punt na aankoop van elk apparaat IBM SENG-3002-01 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen IBM SENG-3002-01 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens IBM SENG-3002-01 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding IBM SENG-3002-01 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over IBM SENG-3002-01 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van IBM SENG-3002-01 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de IBM SENG-3002-01 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met IBM SENG-3002-01 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
