Gebruiksaanwijzing /service van het product IGM1600 van de fabrikant Icom
Ga naar pagina of 32
INSTRUCTION MANUAL iGM1600 SURVIV AL CRAFT 2-W A Y RADIO This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful inter- ference.
i SAFETY TRAINING INFORMA TION Y our Icom radio generates RF electromagnetic energy during transmit mode. This radio has been evaluated for compliance at the distance of 2.
ii RECOMMENDA TION CLEAN THE TRANSCEIVER THOROUGHL Y WITH FRESH W A TER after exposure to saltwater , and dry it before opera- tion. Otherwise, the transceiver ’s keys, switches and con- trollers may become inoperable due to salt crystallization. NOTE: DO NOT remove the battery pack when cleaning the transceiver thoroughly with fresh water .
iii PRECAUTION R W ARNING! NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. R W ARNING! NEVER hold the transceiver so that the antenna is closer than 2.5 cm (1 inch) from exposed parts of the body , especially the face or eyes, while transmitting.
iv SAFETY TRAINING INFORMA TION ............................................... i RECOMMENDA TION ...................................................................... ii FOREWORD ......................................................................
1 OPERA TING RULES 1 D Priorities • Read all rules and regulations pertaining to priorities and keep an up-to-date copy handy . Safety and distress calls take priority over all others. • Y ou must monitor Channel 16 when you are not operating on another channel.
2 2 SUPPLIED ACCESSORIES AND A TT ACHMENTS 1 2 ■ Supplied accessories The following accessories are supplied: Qty . q Handstrap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 w Battery charger (BC-158) . . . . . . . . . . .
3 2 SUPPLIED ACCESSORIES AND A TT ACHMENTS ï Battery pack T o remove the battery pack: T urn the screw counterclockwise, then pull the battery pack in the direction of the arrow as shown below . T o attach the battery pack: Insert the battery pack in the IC-GM1600 completely , then turn the screw clockwise.
4 3 P ANEL DESCRIPTION 2 3 ■ Front, top and side panels q VOLUME CONTROL [VOL] T urns power ON and adjusts the audio level. w MICROPHONE CONNECTOR [MIC/SP] Connects the optional external microphone. NOTE: Attach the [MIC/SP] cap when the optional speaker-microphone is not used.
5 3 P ANEL DESCRIPTION i CHANNEL 16 KEY [16] Selects Channel 16 when pushed. (p. 7) o CHANNEL UP/DOWN KEYS [ Y Y ]/[ Z Z ] ➥ Selects an operating channel. (pgs. 7 – 8) ➥ Selects the SET mode condition of the item. (p. 1 1) ➥ Selects the SET mode item when pushed with [SQL].
6 3 P ANEL DESCRIPTION 3 t BA TTER Y INDICA TOR Indicates remaining battery power . y VOX INDICA T OR “ VOX ” appears when the VOX function is used. (p. 10) u SET MODE ITEM READOUT Indicates the SET mode items while in the SET mode. (p. 1 1) i LOCK INDICA T OR Appears when the lock function is activated.
7 BASIC OPERA TION 4 ■ Channel selection D Channel 16 Channel 16 (Distress channel) is used for establishing initial contact with another station and for emergency communica- tions. While standing by , you must monitor Channel 16. q Push [16] to select Channel 16.
8 4 BASIC OPERA TION 4 ■ Receiving and transmitting q Rotate [VOL] clockwise to turn power ON. w Set the volume and squelch level. ➥ Push [SQL • MONI ], and push [ √ ] to open the squelch. ➥ Push [SQL • MONI ] to stop the “ SQL ” indicator blinking, then rotate [VOL] to set the volume level.
9 4 BASIC OPERA TION ■ Call channel programming The call channel switch is used to select Channel 9* by de- fault, however , you can program your most often-used chan- nel for quick recall. *The channel number depends on version. q Push [CALL] to select the call chan- nel.
10 4 BASIC OPERA TION 4 ■ Lock function This function electronically locks all keys (except for [PTT], [SQL • MONI ] and [Hi/Lo • ]) to prevent accidental channel changes and function access. ➥ Push [Hi/Lo • ] for 1 sec. to turn the lock function ON and OFF .
11 SET MODE 5 ■ SET mode programming SET mode is used to change the condition of 1 1 transceiver functions: beep tone function, monitor switch action, back- lighting function, LCD contrast selection.
12 5 SET MODE 5 ■ SET mode items D Beep tone function “ bP ” Y ou can select silent operation by turning the beep tones OFF , or you can have 2 types of con fi rmation beeps sound at the push of a key . When “ ON ” is selected, a fi xed beep (Pi) sounds, and when “ US ” is selected, the preset beeps (e.
13 5 SET MODE D Auto power save function “ PS ” The auto power save function reduces battery drain by deac- tivating the receiver circuit for preset intervals. • ON : The power save function is turned ON. The power save func- tion will activate when no signal is received, and no operation is performed for 5 sec.
14 5 SET MODE 5 D Battery voltage indicator “ bt ” This function controls display or non-display settings of the connected battery pack ’ s voltage when the power is ON. • The voltage of the connected battery pack is displayed for 2 sec. after power is turned ON.
15 5 SET MODE D VOX delay “ dL ” (A vailable for on-board use only) Sets the VOX delay timer (0.5 to 3.0 sec. in 0.5 sec. steps) keeping the radio in transmit mode after you stop speaking. • Setting the delay to 0.5 (0.5 sec.) is a short VOX delay .
16 6 BP-234 BA TTER Y P ACK 5 6 The optional BP-234 battery pack is a non-rechargeable, Lithium battery pack for operation in a survival craft. The fol- lowing precaution must be observed. • NEVER dispose of the BP-234 battery pack in a fi re. This could re- sult in an explosion.
17 BA TTER Y CHARGING (FOR ON-BOARD USE ONL Y) 7 ■ Battery charging Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. CAUTION: T o avoid damage to the transceiver , turn the power OFF while charging.
18 7 BA TTERY CHARGING (FOR ON-BOARD USE ONL Y) 7 ï Charging connections q Attach the BC-158 to a fl at surface, such as a desk. w Connect the AC adapter as shown below . e Insert the battery pack with/without the transceiver into the charger . • The charge indicator lights green.
19 7 BA TTERY CHARGING (FOR ON-BOARD USE ONL Y) ■ Optional battery chargers ï AD-109 installation q Connect the charger ’ s 10-pin connector to the AD-109 desktop charger adapter ’ s plug.
20 7 BA TTERY CHARGING (FOR ON-BOARD USE ONL Y) 7 ï Rapid charging with the BC-1 19N+AD-109 The optional BC-1 19N provides rapid charging of battery packs. The following are additionally required. • AD-109 charger adapter • An AC adapter (BC-145A/E)* 1 or the DC power cable (OPC-515L/CP-17L).
21 OPTIONAL SWIVEL BEL T CLIP 8 ■ MB-86 contents Qty . Belt clip ………………………………………………………… 1 Base clip ……………………………………………….
22 9 OPTIONAL SPEAKER-MICROPHONE (FOR ON-BOARD USE ONL Y) 8 9 ■ HM-125 descriptions NEVER immerse the connector in water without connecting with the transceiver . If the connector becomes wet, be sure to dry BEFORE connecting it to the transceiver .
23 CHANNEL LIST FOR SUR VIV AL OPERA TION 10 Channel number TX/RX Channel number TX/RX Channel number TX/RX 06 156.300 MHz 08 156.400 MHz 09 156.450 MHz 10 156.500 MHz 1 1 156.550 MHz 12 156.600 MHz 13 156.650 MHz 14 156.700 MHz 15* 156.750 MHz 16 156.
24 11 TROUBLESHOOTING 10 11 The transceiver does not turn ON. No sound from the speaker . T ransmitting is impos- sible, or high power can not be selected. The displayed channel cannot be changed. No beeps. Self check error . (T emperature) Self check error .
25 SPECIFICA TIONS 12 D GENERAL • Frequency coverage TX/RX : 156.300 – 156.875 MHz • Mode : 16K0G3E • Channel spacing : 25 kHz • Power supply requirement : Battery packs (BP-234 or BP- 224*) *For on-board use only • Current drain (approx.) : TX High (2 W) 1.
26 13 OPTIONS 12 13 D BA TTER Y P ACKS <FOR SURVIV AL CRAFT USE> • BP-234 LITHIUM BA TTERY P ACK 9.0 V/3300 mAh Lithium battery pack. <FOR ON-BOARD USE> • BP-224 Ni-Cd BA TTERY P ACK 7.2 V/750 mAh Ni-Cd battery pack. • BP-225 Ni-Cd BA TTERY P ACK 7.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-6383D-1EX Printed in Japan © 2004 Icom Inc..
Een belangrijk punt na aankoop van elk apparaat Icom IGM1600 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Icom IGM1600 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Icom IGM1600 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Icom IGM1600 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Icom IGM1600 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Icom IGM1600 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Icom IGM1600 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Icom IGM1600 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
