Gebruiksaanwijzing /service van het product PH30.2 van de fabrikant a/d/s/
Ga naar pagina of 24
analog and digital systems PH30.2 owner's manual front_cover.qxd 10/26/56 5:13 AM Page 2.
table of contents introduction 1 about this manual 2 features of your PowerPlate™ 2 warning and tips 3 mounting locations 3 system planning 4 system configurations 5-9 amplifier and crossover contr .
about this manual T o get the most from your a/d/s/ PowerPlate™, we recommend that you have the installation performed by your qualified authorized a/d/s/ dealer . If this unit is installed by your dealer , we will extend the warranty to two years instead of the standard one-year .
war nings and tips Always disconnect the battery ground wir e before doing any work on your vehicle. Reconnect the cable only after the installation is complete and the wiring has been checked to make sure that ther e are no problems.
system planning Proper system planning is the best way to maximize your PowerPlate’ s™ performance. By planning your installation carefully you can avoid situations wher e the performance or the reliability of your system is compromised. Y our authorized a/d/s/ dealer has been trained to maximize your system’ s sonic potential.
system configurations All a/d/s/ PowerPlates™ provide extensive featur es, which make a variety of system configurations possible. It is not feasible to cover all of the possibilities within the few pages of this manual.
System 2 - PH30.2 used in 5-channel mode with the AC502 providing level contr ol for bridged channels 5 and 6. 1 and 2 are high-passed for fr ont speaker and channels 3 and 4 are high-passed for r ear speakers. Although shown as a 4-channel input, the source unit can be either 2 or 4-channel depending on the setting of the 2/4 channel switch.
System 4 - PH30.2 used in 4-channel mode with high-pass tweeters and bandpass midrange. Channels 1and 2 are configur ed high-pass for the main tweeters and channels 3 and 4, and 5 and 6 are configur ed bandpass for main midrange. Channels 4 and 6 are contr olled by the 3/4 level control and cr ossover section.
System 6 - PH30.2 used in 3-channel bridged mode with two channels dedicated for the main speakers and one bridged channel pair used for a subwoofer . Channels 1/2, and 3/4 are configur ed high-pass for the main front speakers using a single pair of RCA inputs to pr oduce a bridged mono output.
System 7 - T wo PH30.2’ s are used. The first PH30.2 is configured the same as system 4 and the second PH30.2 is configured similar to system 5. The first amplifier drives the fr ont midrange and tweeters and the second amplifier drives the rear speakers and the subwoofer .
10.
1. 2ch/4ch input switch- Leave this switch OUT if you are using 4 channels of input. Push the switch IN if you have only 2 channels of input to send input 1 and 2 to channels 3 and 4, respectively . (see page 15) 2. 5/6 source- This switch selects the sour ce for channel 5 and 6.
installation 1. Disconnect the battery ground cable. Reconnect the gr ound cable only after the installation is complete and the wiring has been checked to make sure that ther e are no pr oblems. If your radio features a code type security system, be sur e you know the code before disconnecting the battery! 2.
speaker connections for stereo configurations Minimum r ecommended impedance is 2 ster eo. Speaker terminals accept up to A WG #12 speaker wire. speaker connections for bridged configurations Minimum recommended i mpedance is 4 when bridged to subwoofers and 4 when bridged to full range speakers.
signal sour ces Due to the wide input level adjustment range, all a/d/s/ PowerPlates™ can be driven with either a conventional preamplifier drive signal or the amplifier signal fr om a powered sour ce unit.
inter nal signal r outing 2-channel/4-channel input switch - routes RCA input fr om channels 1/2 to channels 3/4. When the switch is engaged, channel 1 input is routed to both amplifier channels 1 and 3 with input channel 2 routed to amplifier channels 2 and 4.
multi-cr oss™ cr ossover configuration xover control 1/2- The cr ossover selection for channels 1 & 2 has three options: When the switch is in the left position, the crossover section of the amplifier is bypassed. Channels 1 & 2 output is full range.
Constant Bass cir cuit T o mix sub-bass information into channels 1/2 and 3/4, select a low- pass crossover point, and use the level contr ols to set the level of sub- bass signal sent to channels 1/2 and 3/4.
adjusting input sensitivity The input sensitivity setting is important to ensure pr oper performance, low noise levels, and maximum system reliability .
tr oubleshooting symptom possible cause action to take no output low or no remote turn-on check remote turn-on voltage input output at amplifier and correct as needed fuse blown check power wire integ.
symptom possible cause action to take distorted output (cont’d) speakers are blown check system with known working speakers and repair or replace as needed poor bass response speakers wired with wr .
specifications amplifier section PH 30.2 power output 4 (watts)1 6 channel 6 x 75 3 channel 3 x 250 power output 2 (watts)2 6 x 112.5 fuse type 70 A maxi dimensions 13" x 19 7/8" x 2" distortion all channels driven <0.
warranty information LIMITED TWO YEAR CONSUMER W ARRANTY Directed Electr onics, Inc. promises to the original pur chaser , to replace this pr oduct should it prove to be defective in workmanship or ma.
a Directed Electronics, Inc. All rights reserved G49200 09-02 front_cover.qxd 10/26/56 5:13 AM Page 1.
Een belangrijk punt na aankoop van elk apparaat a/d/s/ PH30.2 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen a/d/s/ PH30.2 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens a/d/s/ PH30.2 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding a/d/s/ PH30.2 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over a/d/s/ PH30.2 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van a/d/s/ PH30.2 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de a/d/s/ PH30.2 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met a/d/s/ PH30.2 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
