Gebruiksaanwijzing /service van het product ZEQ25GT van de fabrikant iOptron
Ga naar pagina of 41
iOptron ® ZEQ25GT Balanced GoTo Equatorial Mount With Go2Nova ® 8408 Hand Controller Instruction Manual Product #7100, #7101 and #7102.
2 Table of Content Table of Content ................................................................................................................................................. 2 1. ZEQ25GT Overview ...............................................
3 5.5.2. Record PEC .................................................................................................................................... 26 5.6. Set User Objects .........................................................................
4 1. ZEQ25GT Overview Welcome to a new type of EQ mount! The iOptron “Z” des ign mount puts the payload weight at the center of gravity allowing for greater natural stability. Thi s also means the mount is extremely light compared to its payload—a nice benefit when setting up at a remote site.
5 2. ZEQ25 Terms 2.1. Parts List 1 There are two shipping boxes for a regular tri pod version. One box contains a ZEQ mount, hand controller, one 10.4 lbs (4.7kg) cou nterweight, counterweight shaft, tripod spreader and accessories. The other box contains a tripod.
6 2.2. Assembly Terms Polar Axis Cover Polar Scope Cover Polar Axis (R.A. axis) Azi. Adj. Knob Lat. Adj. Knob Lat. Locki ng T-bolt CW mounting nose Front C W position scr ew R.A. Drive Unit DEC Drive Unit Dovetail Saddle Main board CW Safety Screw CW Bar Counterweigh t CW Locki ng Screw Polar Axis Cover Polar Scope Cover Polar Axis (R.
7 2.3. ZEQ25 Ports Ports on the mount DEC Unit R.A. Un it Main Board Main Bo ard DEC Unit R.A. Un it Main Board Main Bo ard Figure 2. Ports on a ZEQ25 mount On main control board: • OFF/ON Switch: P.
8 The Go2Nova ® 8408 hand controller (HC) shown in Figure 3 is the standard controllers that used for a ZEQ25 mount. It has a 4 line, 21 character large LCD screen, function keys, dire ction keys and number keys on the front; a and a HBX port (6-pin) and a serial port ( 4-pin) at the bottom.
9 Figure 6. 8408 HC LCD Information Screen 1. Target Name/Mount Position: displays the name of the target that telescope is currently pointed to or the current mount position.
10 3. ZEQ25GT Mount Assembly 3.1. Introduction You have just purchased a telescope mount that is capable of taking you to a new level of astronomy. No matter which telescope or optical tube assembly (OTA) you select to install on the mount, the overall performance will be greatly enhanced.
11 WARNING: Please DO NOT rock t he counterweight shaft rigorously. You’ll degrade the performance of the spring loaded gear meshing system, or even damage it. WARNING: The new Gear Sw itch will allow you to have most precise weight balance. This also means the mount or OTA will swing FREELY when the Gear Switch is disengaged.
12 Alignment Peg Tray Loc king Knob Accessory Tray Center Rod Knob Figure 8. Set up tripod STEP 3. Attach the ZEQ25 Mount Retract both Azimuth Adj. Knobs to allow enough clearance inside the chamber. Position the mount on the tripod head with the Alignment Peg in between the 2 Azimuth Adj.
13 (1) Remove CW Shaft Locking Screw from the CW Mounting Nose. (2) Insert CW shaft into the CW Mounting Nose as indicated in 2nd photo below. (3) Lock it using CW Shaft Locking Screw from the other side of the CW Mounting Nose. Tighten the Front CW Positioning Screw which is located in front of the CW Mounting Nose.
14 Rotate the DEC axis to horizontal position. Adjust the CW position to balance the mount in R.A. axis (Figure 14a) and move the OTA position to balance the mount along DEC axis (Figure 14b).
15 To set up the controller, press MENU button on the hand controller. From the main menu, scroll down and select “ Set Up Controller ” Press ENTER and select “Set Up Time and Site” Press ENTER. A time and site information screen will be displ ayed: Set Local Time The time will be updated automatically when the GPS has picked up a signal.
16 Set Observation Site Coordinate The third and fourth lines display th e longitude and latitude coordinates, respectively. The longitude and latitude coordinates will be automatically updat ed when the GPS picks up satellite signals.
17 If a ZEQ25GT mount equipped with an iOptron’s AccuAligning TM polar scope, you can do a fast and accurate polar axis alignment with iOptron’s Quick Polar Alignment procedure.
18 NOTE: If you are located in southern hemisphere, Sigma Octantis will be chosen for Polar Alignment. For example, on May 20, 2010, 20:00:00 in Sydney , Australia (Lat S33º51’36” and Long E151º12’40”), 600 min ahead of UT, the Sigma Octantis Position is 1hr21.
19 Figure 20. Zero position.
20 4. Getting Started In order to experience the full GOTO capability of GOTONOVA ® technology it is very important to set up the mount correctly before observation. 4.1. Setup the Mount and Polar Alignment Assemble your ZEQ25 mount according to Section 3.
21 4.5. Star Identifying Function The 8408 hand controller has a star identifying function. After Polar Alignment and Set Up Time and Site , slew the telescope to an bright star, manually or using GOTO. Press ? (Help) button to identify the star name telescope is pointing to, as well as nearby bright stars if there are any.
22 5. Complete Functions of Go2Nova ® 8408 Hand Controller 5.1. Slew to an Object Press the MENU button. From the main menu select “ Select and Slew .” Select an object that you would like to observe and press the ENTER key. The Go2Nova ® 8408 hand controller has a database of about 50,000 objects.
23 5.1.7. User Objects It can store up to 60 used entered objects, including comets. 5.1.8. Enter R.A. DEC Here you can go to a target by entering its R.A. and DEC numbers. 5.2. Sync to Target This operation will match the telescope's current coordinates to Target Right Ascension and Declination.
24 Press ENTER. A R.A. anti-backlash screen will display: To adjust steps move the cursor to each digit and use the number keys to input number directly. Press ENTER – “DEC anti-backlash” will display: Move the cursor to each digit and use the number keys to set the anti-backlash.
25 5.3.9. Upgrade RA & DEC Use this operation to upgrade 8408 hand controller, R.A. and DEC motor controller firmware. Please refer to iOptron online documents for ZEQ25 firmware upgrade details. The password is 9999 . 5.4. Align This function is used for aligning the telescope.
26 If you’ve done with the two star alignment, press the BACK button to finish the alignment. Press ENTER key to select third star for further alignment. 5.4.5. Pole Star Position This shows Polaris position in northern hemispher e or Sigma Octantis position in southern hemisphere, which is used for Quick Polar Alignment.
27 Press ENTER to bring up user objects setting screen. Select “ Add a New Record ”. A screen will display asking to Enter R.A. DEC : You may enter the R.A. and DEC c oordinates of the star you want to watch, and press ENTER. A confirmation screen will show.
28 6. Maintenance and Servicing 6.1. Maintenance The ZEQ25GT is designed to be maintenance free. Do not overload the mount . Do not drop the mount, this will damage the mount or degrade the GOTO tr acking accuracy permanently. Use a wet cloth to clean the mount and hand controller.
29 Appendix A. Technical Specifications Mount “Z Balanced” Equatorial Mount Payload 27 lb (12.3kg), exclude counterweight Mount weight 10.4 lb (4.7kg) Payload/Mount weight 2.
30 Appendix B. Go2Nova ® 8408 HC MENU STRUCTURE MENU Select and Sle w Select and Sle w Solar Syste m Solar Syste m Comets Comets Asteroids Asteroids Stars Stars Mercur y Venus Mars Jupiter Satur n Ur.
31 Set Polar Light Align Align Firmware In formation Firmware In formation Polar Align Polar Align One Star Align One Star Align Multi-Star Align Multi-Star Align Pole Star Posit ion Pole Star Posit i.
32 Appendix C. Firmware Upgrade The firmware in the 8408 hand controller and motor control boards can be upgraded by the customer. Please check iOptron’s website, www.iOptron.com , under Support Directory/ZEQ Mounts, select ZEQ25GT with 8408 Hand Controller, for detail.
33 Appendix D. Computer Control an ZEQ25GT Mount The ZEQ25GT mount can be connected to a computer using supplied RS232 cable. A RS232 to USB adapter (not supplied) is needed if your computer does not have a serial port, like most of t he laptops on the market today.
Appendix E. Go2Nova ® Star List Messier Catalog This table is licensed under the GNU Free Documentation License . It uses material from the Wikipedia article List of Messier objects.
35 001 Acamar 050 Asellus Australis 099 Kaus Media 148 Rastaba 002 Achernar 051 Asellus Borealis 100 Keid 149 Regulus 003 Acrux 052 Aspidiske 101 Kitalpha 150 Rige l 004 Acubens 053 Atik 102 Kochab 15.
No. Constellation Abbreviation No. Constellation Abbreviation 1 A ndromeda A nd 45 Lacerta Lac 2 A ntlia A nt 46 Leo Leo 3 A pus A ps 47 Leo Minor LMi 4 A quarius A qr 48 Lepus Lep 5 A quila A ql 49 L.
ID No. OBJECT NGC # Messier# IC# A (A bell) U(UGC) ID No. OBJECT NGC # Messier# IC# A (A bell) U(UGC) 1 Andromeda Galaxy 224 31 31 Hind's Variable Nebula 1555 2 Barnards Galaxy 6822 32 Hubble&apo.
No. Ob j ect Const Sep. Ma g itude SAO Comm. Name No. Ob j ect Const Sep. Ma g itude SAO Comm. Name 1 Gam And 9.8 2.3 / 5.1 37734 Almaak 36 Eta Cas 12.9 3.5 / 7.5 21732 Achird 2 Pi And 35.9 4.4 / 8.6 54033 37 Iot Cas 2.3 4.7/7.0/8.2 12298 3 Bet Aql 12.
No. Ob j ect Const Sep. Ma g itude SAO Comm. Name No. Ob j ect Const Sep. Ma g itude SAO Comm. Name 71 Bet C yg 34.4 3.1 / 5.1 87301 Albireo 106 Del Her 8.9 3.1 / 8.2 84951 Sarin 72 Omi 1 C yg 107 3.8 / 6.7 49337 107 Mu Her 34 3.4 / 9.8 85397 73 52 Cyg 6.
No. Ob j ect Const Sep. Ma g itude SAO Comm. Name No. Ob j ect Const Sep. Ma g itude SAO Comm. Name 141 Eps 2 Lyr 2.3 5.2 / 5.5 67315 Double dbl2 176 Zet Psc 23 5.6 / 6.5 109739 142 Alp Mic 20.5 5.0 / 10 212472 177 Kap Pup 9.9 4.5 / 4.7 174199 143 Zet Mon 32 4.
IOPTRON TWO YEAR TELESCOPE, MO UNT, AND CONTROLLER WARRANTY A. iOptron warrants your telescope, mount, or cont roller to be free from defects in materials and workmanship for two years. iO ptron will repair or replace such product or part which, upon inspection by iOptron, is found to be defective in materials or workman ship.
Een belangrijk punt na aankoop van elk apparaat iOptron ZEQ25GT (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen iOptron ZEQ25GT heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens iOptron ZEQ25GT vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding iOptron ZEQ25GT leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over iOptron ZEQ25GT krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van iOptron ZEQ25GT bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de iOptron ZEQ25GT kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met iOptron ZEQ25GT . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
