Gebruiksaanwijzing /service van het product BB2250 van de fabrikant Jonsered
Ga naar pagina of 17
Please read the operator’ s manual carefully and make sure you understand the instructions before using the machine. 115 32 10-26 English Operator’ s manual Original Instr uctions BB2250_English.
English 2 EC-declaration of conf ormity (Applies to Europe onl y) Husqvarna AB, SE-561 82 Huskv arna, Sweden, tel +46-36-146500, declares under sole responsibility that the blow ers Jonsered BB22 50 w.
English 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY FIRST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
English 4 SAFETY FIRST Instructions contained in warnings within this manual and warning seals marked with a symbol on the blo wer concern critical points which must be taken into consideration to pre v ent possible serious bodily injury , and for this reason y ou are requested to read all such instructions carefully and follow them without fail.
English 5 For saf e operation and maintenance, symbols are car ved in relief on the machine. Using to these indications, please be careful not to make a mistak e.
English 6 WORKING CONDITIONS 1. Refrain from operating the b lower if y ou are tired, ill, or upset, or if you are under the influence of alcohol, drugs or medication 2. T o reduce the r isk of hearing loss associated with sound lev els, hearing protection is required.
English 7 W ARNING Check to see if the shoc k-absorbers have become crac ked or otherwise damaged. Note that failing to replace these rubber and spring mounts when they have become crac ked or damaged may cause the engine to come loose fr om its frame during use, thus resulting in possib le serious bodily injury .
English 8 MAINTENANCE 1. In order to maintain your product in proper working order , perform the maintenance and checking oper ations described in the manual at regular intervals. 2. Alwa ys be sure to turn off the engine and disconnect the spark plug before perf orming any maintenance or checking procedures.
English 9 1. F rame 2. Harness 3. Engine Cov er 4. V olute Case, Cov er 5. Net 6. Air Cleaner 7. Recoil Star ter 8. Fuel T ank 9. Spark Plug Cap 10.Choke Lev er 11. Control handle 12. Stop Switch 13. Throttle Lev er 14. Elbow 15. Clamp (large) 16. Flexible hose 17.
English 10 MODEL BB2250 Dimensions (L x W x H) mm 401x460x495 Dry W eight (including pipes) kg 10.1 Dry W eight (without accessories) kg 9.4 Fuel T ank Capacity liter 2.
English 11 ■ FLEXIBLE HOSE AND SWIVEL JOINT 1. Connect the blo wer and s wivel joint with fle xible hose . Clamp both ends of the flexib le hose securely with the hardware supplied with the unit.
English 12 ■ FUEL W ARNING • Gasoline is very flammable. A void smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground f or fueling and move at least 10ft (3m) a way from the fueling point bef ore starting the engine .
English 13 ■ ST AR TING ENGINE IMPORT ANT • A void operating the b lower with the flexib le tube and swivel joint disconnected. That will reduce the cooling air and the engine could be damaged by o verheating. 1. Push the primer bulb until fuel flows out in the clear tube .
English 14 ■ ADJUSTING IDLE SPEED • The idling speed is set for 2000 rpm at the factory . If it is necessar y to adjust the idle speed, use the adjustment screw on the top side of carb uretor . (1) Idling Adjustment Screw ■ ST OPPING ENGINE • Mov e the throttle lev er to the idling position and set the stop s witch to the stop position.
English 15 Maintenance, replacement, or repair of the emission control de vice and systems ma y be performed by an y non-road engine repair establishment or individual. W ARNING Make sure that the engine has stopped and is cool before perf orming any service to the blower .
English 16 ■ SP ARK PLUG • The spark plug may gather carbon deposits on its firing end with reasonable use . Remov e and inspect the spark plug ev ery 25 hours and clean the electrodes as necessary with a wire br ush. The spar k gap should be adjusted to .
English 17 ■ AIR INLET NET IMPORT ANT • Blown air is taken in fr om the air inlet net. If the air flow drops during opera- tion, stop the engine and inspect the air inlet net for bloc kage by obstac les. • Note that failure to remove an y such obstacles ma y result in the engine becoming overheated and damaged.
Een belangrijk punt na aankoop van elk apparaat Jonsered BB2250 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Jonsered BB2250 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Jonsered BB2250 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Jonsered BB2250 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Jonsered BB2250 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Jonsered BB2250 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Jonsered BB2250 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Jonsered BB2250 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
