Gebruiksaanwijzing /service van het product GR-DV801 van de fabrikant JVC
Ga naar pagina of 88
L YT1107-001A Master P age: Cover1 EN ENGLISH GR-D V801 AU TO M AT I C DEMONSTRA TION 9 GETTING ST ARTED 10 VIDEO RECORDING & PLA YBA CK 17 DIGIT AL STILL CAMERA (D.
2 EN Master P age: Left-Safety-Dummy Using T his Instruction Manual ● All major sections are listed in the T able Of Contents on the cover page. ● Notes appear after most subsections . Be sure to read these as well. ● Basic and adv anced features/operation are separ ated for easier refer ence.
EN 3 Master P age: Right-Safety When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear). Do not block the ventilation holes.
4 EN Master P age: Left-Safety SAFETY PRECAUTIONS Do not point the lens or the viewfinder direct ly into the sun. T his can cause eye injur ies, as well as lead to the malfunctioning of internal circuitry . There is also a risk of fire or electric shoc k.
EN 5 Master P age: Right NOTES: ● In order to maintain optimum performance of the camc order , provided cables ma y be equipped with one or more core filter . If a cable has only one core filter , the en d that is closest to the filte r should be connected to the camcorder .
6 EN Master P age: Left How T o Use The Audio Cable When using optional headphones or external microphone, connect to the provided Audio cable (with a core filter attached), then connect the A udio cable to the camcorder . The core filter reduces interference.
EN 7 Master P age: Right How T o Attach The Lens Cap T o protect the lens, attach the provided lens cap to the camcorder as shown in the illustration. NOTE: T o confirm the lens cap is on correctly make sure the cap is flush to the camcorder . ● During shooting GR-DV801US.
8 EN Master P age: Left-Heading0 CONTENTS AUTOMATIC DEMONSTRATION 9 GETTING STARTED 10 Power ........... ..................... ................. ..................... . 10 Grip Adjustment ................... .................. .................. 12 Viewfinder Adju stment .
EN 9 Master P age: Right-start A UTOMA TIC DEMONSTRA TION Automatic Demonstr ation takes place when “DEMO MODE” is set to “ON” (factory-preset). 䡲 Automatic Demonstration starts w hen there is no operation for about 3 minutes after the P ower Switch is set to “ A ” or “ M ” and no cassette is in the camcorder .
Master P age: Left-start 10 EN GETTING ST ARTED T his camcorder’ s 2-way po wer supply system lets you c hoose the most appropriate source of power .
EN 11 Master P age: Right INFORMA TION: T he optional extended-use ba ttery pac k kit is a set composed of a battery pack and A C P ower Adapter/ Charger: VU-V840 KIT : B N-V840U battery pack & AA.
12 EN Master P age: Left-Heading0 1 Adjust the velcro strip. 2 P ass your right hand through the loop and grasp the grip. 3 Adjust your thumb and fingers through the grip to easily operate the Recording Start/Stop Button, P ower Switc h and P ower Zoom Lev er .
EN 13 Master P age: Right 1 Set the P ower Switc h to “ M ” or “PLA Y” while pressing down the Lock Button located on the switch. 2 Open the LCD monitor fully , or pull out the viewfinder fully . 3 Press the MENU Wheel in. T he Menu Screen appears.
14 EN Master P age: Left-Heading0 T he date/time is recorded onto the tape at all times, but its display can be turned on or off during pla yback. ( 墌 pg. 31, 41) 1 Set the P ower Switc h to “ M ” while pressing down the Lock Button located on the switch.
EN 15 Master P age: Right T he camcorder needs to be powered up to load or eject a cassette. 1 Slide and hold OPEN/EJECT in the direction of the arrow , then pull the cassette holder cover open until it locks. T he cassette ho lder opens automatically .
16 EN Master P age: Left-Heading0 T he provide d memory card is alread y inserted in the camcorder at the time of purchase. 1 Make sure the camcor der’ s power is off. 2 Open the card cov er (MEMOR Y C ARD). 3 T o load a memory card , firmly insert it with its clipped edge first.
EN 17 Master P age: Right-start VIDEO RECORDING & PLA YB A CK VIDEO RECORDING NOTE: Before continuing, perfor m the procedures listed below: ● Pow e r ( 墌 pg. 10 ) ● Loading A Cassette ( 墌 pg. 15) 1 Remove the lens cap. 2 Press PUSH OPEN and open the LCD monitor fully , o r pull out the viewfinder fully .
18 EN Master P age: Left Zooming Produces the zoom in/out effect, or an instantaneous change in image magnification. Zoom In Slide the P ower Zoom Lever towards “T”. Zoom Out Slide the P ower Zoom Lever towards “W”. ● T he further you slide the P ower Zoom Lev er , the quicker the zoom action.
EN 19 Master P age: Right Ti me C o d e During recording, a time code is recorded on the tape. T his code is to confirm the location of the recorded scene on the tape during playbac k. If recording starts from a blank portion, the time code begins counting from “00:00:00” (minute:second:frame).
20 EN Master P age: Left-Heading0 VIDEO PLA YBA CK 1 Load a cassette. ( 墌 pg. 15) 2 Set the VIDEO/MEMOR Y Switch to “VIDEO”. 3 Set the P ower Switc h to “PLA Y” while pressing down the Loc k Button located on the switch. 4 T o start playback, press 4 / 9 .
EN 21 Master P age: Right Shuttle Search Allows high-speed searc h in either direction durin g video playbac k. 1) During play back, press 5 for forw ard search, or 3 for reverse searc h. 2) T o resume normal playback, press 4 / 9 . ● During playbac k, press and hold 5 or 3 .
22 EN Master P age: Left-Heading0 VIDEO PLA YBA CK (cont.) T hese are some basic type s of connections. When making the connections, refer also to your VCR and TV instruction manuals. * Not required for watching still images only . ** Connect when y our TV/VCR has only A/V input connectors.
EN 23 Master P age: Right-start DIGIT AL STILL CAMERA (D.S.C.) RECORDING & PLA YBA CK D.S.C. RECORDING Y ou can use your camcorder as a Digital Still Camera for taking snapshots. Still images are stored in the memory card. NOTE: Before continuing, perfor m the procedures listed below: ● Pow e r ( 墌 pg.
24 EN Master P age: Left-Heading0 D.S.C. PLA YBA CK Images shot with the cam corder are automatically numbered, then stored in numerical order in the memory card. Y ou can view the stored image s, one at a time, much like flipping through a photo album.
EN 25 Master P age: Right Y ou can view video clips ( 墌 pg. 50) stored in the memory card. 1 Load a memory card. ( 墌 pg. 16) 2 Set the VIDEO/MEMOR Y Switch to “MEMOR Y”. 3 Set the P ower Switc h to “PLA Y” while pressing down the Loc k Button located on the switch.
26 EN Master P age: Left Y ou can view several different files stored in the memory card at a time. This bro wsing capability makes it easy to locate a particular file you want. 1 F or Index Pla yback of image files , perform 1 – 6 in “Normal Playbac k Of Images” ( 墌 pg.
EN 27 Master P age: Right T he Protect mode helps prevent the accidental erasure of files. 1 Load a memory card. ( 墌 pg. 16) 2 Set the VIDEO/MEMOR Y Switch to “MEMOR Y”. 3 Set the P ower Switc h to “PLA Y” while pressing down the Loc k Button located on the switch.
28 EN Master P age: Left T o remov e protection from all files stored in the memo ry card 9 Rotate the MENU Wheel to select “C ANC.ALL ”, and press it. T he PRO TECT screen appears. 10 Rotate the MENU Wheel to select “EXECUTE”, and press it. ● T o cancel selection, select “RETURN”.
EN 29 Master P age: Right By resetting the file name , a new folder will be made. T he new files you are going to make will be stored in the new folder . It is convenient to separate the new files from previously made files. (A vailable only for Image and video clip files.
30 EN Master P age: Left T o Print By Select ing Still Images And Number Of Prints 1 P erform steps 1 – 8 in “T o Print All Still Images (One Print F or Each)” ( 墌 pg. 29). 2 Rotate the MENU Wheel to select “CURRENT”, and press it. T he DPOF screen appears.
EN 31 Master P age: Right-start ADV ANCED FEA TURES MENUS FOR DET AILED ADJUSTMENT T his camcorder is equipped with an easy-to-use, on- screen menu system that simplifies many of the more detailed camcorder settings. ( 墌 pg. 32 – 41) 1 F or Video and D .
32 EN Master P age: Left-Heading0X2 MENUS FOR DET AILED ADJUSTMENT (cont.) 4) Press the MENU Wheel in. T he Menu Screen returns. ● Repeat the procedure if you wish to set other function menus. 5) Press the MENU Wheel in again. T he Menu Scree n closes.
EN 33 Master P age: Right W I P E–C O R N E R : Wipe in on a black screen from the upper right to the lower left corner , or wipe out from lower left to upper right, leaving a blac k screen.
34 EN Master P age: Left RECORDING ME NUS (cont.) SEPIA : Recorded scenes hav e a brownish tint like old photos. Combine this with the Cinema mode for a classic look. MONO TON E : Like classic black and w hite films, your footage is shot in B/W . Used together with the Cinema mode, it enhances the “classic film” effect.
EN 35 Master P age: Right Zooming ZOOM (F actory-preset: 40X ) 10X : When set to “10X” while using digital zoom, the zoom magnification will reset to 10X since digital zoom will be disengaged.
36 EN Master P age: Left MANUAL Digital Image Stabilization T o compensate for unstable i mages caused by camera-shake, particularly at high magnification.
EN 37 Master P age: Right Wide mode WIDE MODE (F actory-preset: OFF ) OFF : Records with no change in the screen ra tio. F or pla yback on a TV with a normal screen ratio. CINEMA * : Inserts black bands at the top and bottom of the screen. T he indicator appears.
38 EN Master P age: Left Automatic demonstration mode Demonstrates certain functions such as Progr am AE with special effect s, etc., and can be used to c onfirm how these functions operate. ( 墌 pg. 9) DEMO MODE (F actory-preset: ON ) OFF : Automatic demonstration will not take place.
EN 39 Master P age: Right DSC Picture quality T he Picture Quality mode can be selected to best match your needs. T wo Pi cture Quality modes are a vailable: FINE ( ) and ST AND ARD ( ) (in order of quality).
40 EN Master P age: Left-Heading0 PLA YBA CK MENUS VIDEO Playback sound During tape playbac k, th e camcorder detects the sound mode in whic h the recording was made, and pla ys the sound back. Select the type of sound to accompany y our playbac k picture.
EN 41 Master P age: Right SYSTEM Each setting is linked with “ s ”, whic h appears when the P ower Switch is set to “ M ”. ( 墌 pg. 31) T h e parameters ar e the same as in the description on page 37.
42 EN Master P age: Left-Heading0 FEA TURES FOR RECORDING Makes dark subjects or areas even brig hter than they would be under good natural lighting. Although the recorded image is not grainy , it ma y look as if it is strobing due to the slow shutter speed.
EN 43 Master P age: Right ● If Program AE with special effects ( 墌 pg. 33) is engaged, certa in modes of Program AE with special effects are disabled during Snapshot recording. In such a case, the icon blinks. ● If SNAPSHO T is pressed when “DIS” is set to “ON” ( 墌 pg.
44 EN Master P age: Left NOTE: If “BEEP” and “T ALL Y” are set to “OFF” ( 墌 pg. 37), the beep does not sound and the tally lamp does not light. A selection of titles/frames stored in the provided memory card can be superimposed. Tit le S e le c ti on 1 P erform steps 1 to 6 in “Playbac k Of T itle Images” ( 墌 pg.
EN 45 Master P age: Right T he camcorder’ s Full Range AF system offers continuous shooting ability from close-up (as close as approx. 5 cm (2”) to the subject) to infin ity .
46 EN Master P age: Left Manual exposure control is recommended in the following situations: ● When shooting using reverse lighting or w hen the background is too bright. ● When shooting on a reflective natur al background such as at the beach or w hen skiing.
EN 47 Master P age: Right Backlight compensation brightens the subject quickly . Press BACK L IG HT . The indicator is display ed and the subject is brightened.
48 EN Master P age: Left T he Na vigation Function helps you chec k tape contents by making thumbnail images on a memory card. T o make thumbnail images during video recording aut omatically 1 Load a cassette. ( 墌 pg. 15) 2 Load a memory card. ( 墌 pg.
EN 49 Master P age: Right ● T he “NA VIGA TION SEAR CH” indication appears blinking and the camcorder starts searching the tape for the relev ant point of the selected thumbnail image. T o cancel NA VIGA TION search midw ay ... Press 4 / 9 , 3 , 5 or 8 .
50 EN Master P age: Left Y ou can make video clips in 160 x 120 pixels from real-time camer a image or recorded video footage and store them in a memory card as files which can be conveniently sent via E-Mail. T o make video clips from real-time camera image 1 Load a memo ry card.
EN 51 Master P age: Right T o make video clips from recorded video footage 1 Load a cassette. ( 墌 pg. 15) 2 Load a memory card. ( 墌 pg. 16) 3 Set the VIDEO/MEMOR Y Switch to “VIDEO”. 4 Set the P ower Switc h to “PLA Y” while pressing down the Loc k Button located on the switch.
52 EN Master P age: Left-Heading0 DUBBING . * Connect when your TV/VCR has an S-VIDEO IN/OUT connector . I n this case, it is not necessary to connect the yellow video cable. ** When connecting the cable, open the co ver . T o use this camcorder as a play er .
EN 53 Master P age: Right It is also possible to copy recorded scenes from the camcorder onto another video unit equipped with a D V connector . Since a digital signal is sent, there is little if any image or sound deterioration. 1 Make sure all units are turned off.
54 EN Master P age: Left It is also possible to copy recorded scenes from another video unit equipped with a DV connector onto the camcorder . Since a digital signal is sent, there is little if any image or sound deterioration. 1 Make sure all units are turned off.
EN 55 Master P age: Right Still images can be dubbed fr om a tape to a memory card. 1 Load a cassette. ( 墌 pg. 15) 2 Load a memo ry card. ( 墌 pg. 16) 3 Set the VIDEO/MEMORY Switch to “VIDEO”. 4 Set the P ower Switch to “PLA Y” while pressing down the Lock Button located on the switc h.
56 EN Master P age: Left-Heading0 USING THE REMOTE CONTROL UNIT T he Full-Function Remote Control Unit can operate this camcorder from a distance as well as the basic operations (Pla yback, Stop, P ause, Fa st-F orward and Rewind) of your VCR. It also makes additional pla yback functions possible.
EN 57 Master P age: Right Buttons And Functions A Infr ared beam tr ansmitting window T ransmits the beam signal. T he following buttons are a v ailable only when the camcorder’ s Power Switc h set to “PLA Y”. B DISPLA Y Button .................
58 EN Master P age: Left . Slow-Motion Playback Allows slow-speed sear ch in either direction during video playbac k. During normal video playbac k, press SLOW ( Y I o r I U ) more than approx. 2 seconds. ● After approx. 5 minutes (approx. 20 seconds with an 80-minute cassete) in Slow Rewind or approx.
EN 59 Master P age: Right T he audio trac k can be customised only when recorded in the 12-bit and SP modes. ( 墌 pg. 34) 1 Pla y back the tape to locate the point where editing will start, then press PA U S E ( 9 ). 2 While holding A. DUB ( D ) on the remote control, press PA U S E ( 9 ).
60 EN Master P age: Left Y ou can record a new scene into a previously recorded tape, replacing a section of the original recording with minimal picture distortion at the in and outpoints. T he original audio remains unchanged. NOTES: ● Before performing the follo wing steps, m ake sure that “TIME CODE” is set to “ON”.
EN 61 Master P age: Right Set Remote/VCR Code 1 T urn off the power to the VCR and point the remote towards the VCR’ s infrared sensor . Then, referring to the VCR CODE LIST , press and hold MBR SET , and enter the brand code. T he code is automatically set once you releas e MBR SET , and th e VCR’ s power comes on.
62 EN Master P age: Left Make Connections Also refer to page 22. * Connect when y our TV/VCR has an S-VIDEO IN connector . In this case, it is not necessary to connect the yellow video cable.
EN 63 Master P age: Right Select Scenes 6 Press PLA Y ( U ) and then press R.A.EDIT ON/OFF on the remote control. T he Random Assemble Editing Menu app ears. 7 If using a Wipe/F ader at the beginning of the scene, press FA D E / W I P E on the remote control.
64 EN Master P age: Left Picture Wipe And Dissolve Menu (av ailable only for Random Assemble Editing) Y ou can use not only the wipe/fader effects on page 32 but also the picture wipe and dissolve effects below . DISSOL VE : T he new scene gr adually appears as the old one gradually disappears.
EN 65 Master P age: Right For More Accurate Editing Some VCRs make the transition from Record-P ause to Record mode faster than others. Even if you begin editing for the camcor der and the VCR a t exactly the same time, you ma y lose scenes you wanted, or find that you ha ve recorded scenes y ou did not want.
66 EN Master P age: Left-Heading0 SYSTEM CONNECTIONS [A] Using USB cable It is possible to do the following things: ● T ransfer still images stored on a memory card to a PC. ● T ransfer still/moving images recorded on a tape to a PC. ● Capture still/moving images in real-time.
EN 67 Master P age: Right T his camcorder can be used as a We bCam via USB connection. 1 Make sure all necessary s oftware (prov ided) are installed in your PC and all units are turned off. 2 Connect the camcorder to your PC using the USB cable. 3 Set the VIDEO/MEMORY Switch to “MEMOR Y”.
Master P age: Left-start 68 EN REFERENCES DET AILS ITEMS NOTES V Po w e r ( 墌 pg. 10) ● Perform c harging wher e the temperatur e is between 10°C and 35°C (50°F and 95°F). 20°C to 25°C (68°F to 77°F) is th e ideal temperature r ange for c harging.
EN 69 Master P age: Right-Heading0 TROUBLESHOOTING If, after following the steps in the chart below , the probl em still exists, please consult your nearest JVC dealer . Power Video and D.S.C . Recording T he camcorder is a microcomputer-controlled device.
70 EN Master P age: Left Video and D.S.C. Playback 7. T he LCD monitor or viewfinder indications blink. 7. • Certain Wipe/F ader eff ects, certain modes of Program AE with special effects, “DIS” and other functions that cannot be used together are selected at the same time.
EN 71 Master P age: Right Advanced features SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION 13. T he focus does not adjust automatically . 13. • Focus is s et to the Manual mode. • T he recording was done in a dark place, or the contrast was l ow . • T he lens is dirty or covered with condensation.
72 EN Master P age: Left Other problems SYMPTOM POSSIBLE CA USES CORRECTIVE ACTION 24. T he power/charge lamp on the camcorder does not light w hen the charging is attempted. 24. • T he temperature of the battery is extremely high/low . • Charging is difficult in places subject to extremely high/ low temperatures.
EN 73 Master P age: Right 33. Colored bright spots appear all over the LCD monitor or the viewfinder . 33. • T he LCD monitor and the viewfinder are made with high-precision technology . Howeve r , black spots or bright spots of light (red, green or blue) ma y appear constantly on the LCD monitor or the viewfinder .
74 EN Master P age: Left-Heading0 CA UTIONS When using the A C Po wer Adapter in a reas other than the USA 䡲 T he provided A C P ower Adapter features automatic voltage selectio n in the AC range from 110 V to 240 V .
EN 75 Master P age: Right Memory Cards T o properly use and store your memory cards, be sure to read the following cautions: 1. During use… ... make sure the memory card bears the SD or MultiMediaCard mark. ... make sure the memory card is positioned properly when inserting.
76 EN Master P age: Left How T o Handle A CD-ROM • T ake car e not to soil or scratch the mirror surface (opposite to the printed surface). Do not write anything or put a stic ker on either the front or back surface. If the CD-ROM gets dirty , gently wi pe it with a soft cloth outward from the center hole using a circular motion.
EN 77 Master P age: Right-Heading0 USER MAINTENANCE 1 T urn off the camcorder . 2 Slide and hold OPEN/EJECT in the direction of the arrow , then pull the cassette holder cover open until it locks. T he cassette ho lder opens automatically . Remove the cassette.
78 EN Master P age: Left-Heading0 SPECIFICA TIONS Camcorder For G e n e ra l P ow er supply : DC 11 V (Using AC Adapter) DC 7.2 V (Using battery pack) P ow er consumption LCD monitor off, viewfinder on : Approx. 3.7 W LCD monitor on, viewfinder off : Approx.
EN 79 Master P age: Right Specifications shown are for SP mode unless otherwise indicated. E & O.E. Design and specifications subject to change without notice. For Connectors S S-V ideo input : Y : 0.8 V to 1.2 V (p-p), 75 Ω , analog C: 0.2 V to 0.
Master P age: Left-start 80 EN INDEX INDEX Contr ols, Connect ors And Indicat ors W X Y Z GR-DV801US.book Page 80 Wednesday, J anuary 22, 2003 5:39 PM.
EN 81 Master P age: Right Controls a •Menu Wheel [MENU] ........................ 墌 pg. 31 •Speaker/Headphone V olume Control [MENU/VOLUME +, –] ... .................. 墌 pg. 20 b Snapshot Button [SNAPSHO T]....... 墌 pg. 23, 42 c P ow er Zoom Lever [T/W] .
82 EN Master P age: Left-Heading0 INDEX Indications Indications LCD Monitor/Viewfinder Indications During Video Recording Only a Navigation Indicator ( 墌 pg. 48) (Appears when “NA VIGA TION” is set to other than “MANUAL ”.) b Selected Wipe/F ader Effect I ndicator ( 墌 pg.
EN 83 Master P age: Right (Appears when Nig ht-Aliv e is engaged.) • : Gain Up Mode ( 墌 pg. 35) (Appears when “GAIN UP” is set to “ AUT O” and the shutter speed is automatically adjusted.) c Flash Indicator (Appears when the optional flash attached to the info-shoe is ready .
84 EN Master P age: Left-Heading0 INDEX Indications (cont .) Wa r n i n g I n d i c a t i o n s Indications Function Displays the battery remaining po wer . Remaining power level: high Remaining power level: exhausted As the battery power comes close to nil, the battery indicator blinks.
EN 85 Master P age: Right Indications Function IN SE RT ER RO R! <CANNOT EDIT ON A LP RECORDED T APE> <CHECK T APE’S ERASE PRO T ECTION T AB> ● Appears if Insert Editing is attempte d on a tape recorded in the LP mode.
86 EN Master P age: Left A AC Adapter ................................................. .. 10, 11 Animation ........................................................... 36 Audio Dubbing ........................................... ........ 59 Auto Focus .
EN 87 Master P age: Right P Picture Quality (QUALITY) .......................... ........ 39 Playback sound (SOUND MODE, 12bit MODE) ........................... 40 Playback Special Effects .............................. ........ 58 Playback Zoom .....
COPYRIGHT© 2003 VICT OR COMP ANY OF JAP AN, L TD . EN GR-D V801 Master P age: Cover4 US Printed in Japan 0203-FO-ID-VP GR-DV801US.book Page 88 Wednesday, J anuary 22, 2003 5:39 PM.
Een belangrijk punt na aankoop van elk apparaat JVC GR-DV801 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen JVC GR-DV801 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens JVC GR-DV801 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding JVC GR-DV801 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over JVC GR-DV801 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van JVC GR-DV801 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de JVC GR-DV801 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met JVC GR-DV801 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
