Gebruiksaanwijzing /service van het product GR-FX120A van de fabrikant JVC
Ga naar pagina of 56
LYT0683-001A EN COMPACT VHS CAMCORDER GR-SXM470A GR-FXM270A GR-FXM170A GR-FXM17A GR-FX220A GR-FX120A GR-FX12A GR-SXM27EA GR-SX22EA INSTRUCTIONS VHS PA L 625 ENGLISH CONTENTS SAFETY PRECAUTIONS 2 – 3 AUTOMA TIC DEMONSTRA TION 4 PROVIDED ACCESSORIES 4 GETTING ST ARTED 6 – 13 RECORDING 14 – 29 Basic Recording .
2 EN Using This Instruction Manual • All major sections and subsections are listed in the T able Of Contents on the cover . • Notes appear after most subsections. Be sure to read these as well. • Basic and advanced features/operation are separated for easier reference.
EN 3 When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both sides, on top and at the rear). Do not block the ventilation holes. (If the ventilation holes are blocked by a newspaper , or cloth etc.
4 EN AUTOMA TIC DEMONSTRA TION Automatic Demonstration takes place when “DEMO MODE” is set to “ON” (factory-preset). A vailable when the Power Switch is set to “ ” or “ ” . Operating the Power Zoom Lever during the demonstration stops the demonstration temporarily .
EN 5 1 2 3 How T o Attach The Core Filter Attach the provided Core Filter to the provided A/V Cable, S-V ideo Cable and AC Adapter . The Core Filter reduces interference. 1 Release the stoppers on both ends of the Core Filter . 2 Run the cable through the Core Filter , leaving approx.
6 EN 2 1 4 3 5 GETTING ST ARTED Power This camcorder ’ s 2-way power supply system lets you choose the most appropriate source of power . Do not use provided power supply units with other equipment. CHARGING THE BA TTERY P ACK 1 Make sure the battery pack is attached to the camcorder .
EN 7 USING AC POWER Use the AC Adapter (connect as shown in the illustration). NOTES: ● The provided AC Adapter features automatic voltage selection in the AC range from 1 10 V to 240 V .
8 EN GETTING ST ARTED (cont.) PAUSE 1 180 ° 180 ° 2 2 3 3 2 4 3 1 A M P L A Y O F F Power Zoom Lever Recording Start/Stop B utton Set to “ ” or “ ” . Shoulder Strap Attachment 1 Following the illustration, thread the strap through the eyelet 1 , then fold it back and thread it through the buckle 2 .
EN 9 R I T T D J D T E N E I A L E R O C T L T T I M E . E L E P O T C T E / U S A I T M T I M R Y M M I A L I D O N S E E M C A M D T R E R N E N E E A O G O M . . M M E E N O O O E 0 O N U F F F N 6 F U F F F G F LIS H F E M T O X . O C P W U O .
10 EN R D W S T D N E . I – A I R E C D V P S E X Z E H E P T T M O S L U S O O L A R Y D M E E Y N S E T N T G E T M H ME S 5 O O T F N P 0 F N 3 U U x F 0 LL R D W S T D N E .
EN 11 Recording Playback NOTES about S-VHS and S-VHS ET JVC EHG (Extra High Grade) tapes are recommended for superior results. Use S-VHS tape for storing recordings for an extended period or for recording important scenes, as it enables higher-quality recording and playback.
12 EN T T T T E 3 4 5 6 X 0 5 0 0 IT TAPE LEN GTH T 30 S L E P P XIT REC M ODE SP GETTING ST ARTED (cont.) T ape length indicator T APE LENGTH Menu MENU Wheel Power Switch T ape Length Setting Set the tape length according to the length of the tape used.
EN 13 Loading/Unloading A Cassette 1 Open the LCD monitor fully (models equipped with LCD monitor only). 2 Slide EJECT until the cassette holder opens. Do not use force to open. 3 Insert or remove a cassette. When inserting, make sure the label is facing outward.
14 EN 180 ° 90 ° BR I G H T – ––––––– 6 ––– + 25 MI N 60MIN 3MIN 2MIN MIN 59MIN 1MIN 0MIN NOTE: Y ou should already have performed the procedures listed below . If not, do so before continuing. ● Power ( pg. 6) ● Load A Cassette ( pg.
EN 15 NOTES: ● If the Record-Standby mode continues for 5 minutes without performing Zoom or any other operations, the camcorder ’ s power shuts off automatically . Set the Power Switch to “ OFF ” , and then back to “ ” or “” to turn the camcorder on again.
16 EN RECORDING Basic Features 1 x 5 S PAUSE RET AKE ( 2 / 3 ) Button Zoom in (T : T elephoto) Zoom out (W: W ide angle) Power Zoom Lever Zoom indicator bar Zooming: T o produce the zoom in/out effect, or an instantaneous change in image magnification.
EN 17 5Sec. Rec (5-sec. Recording) (GR-FXM170A/FXM17A/FX120A/FX12A only) : T o record a scene for 5 seconds, providing quick scene transitions like those seen in TV programmes. 1) Make sure the recording mode is set to “ SP ” . 2) During Record – Standby , press 5SEC.
18 EN RECORDING Advanced Features Snapshot (GR-SXM470A/FXM270A/FX220A/SXM27EA/SX22EA only) Use your camcorder like a regular camera and take a snapshot, or several of them in succession. 1 Set the Power Switch to “ ” or “ ” . 2 Press SNAPSHOT .
EN 19 Fade/Wipe Effects These effects let you make pro-style scene transitions. Fade- or wipe-in works at recording start, and fade- or wipe-out works at recording end. 1 Set the Power Switch to “ ” . 2 Press F ADE/WIPE repeatedly until the desired mode ’ s name and indication appear .
20 EN Program AE With Special Effects 1 Set the Power Switch to “ ” . 2 Press P .AE repeatedly until the desired mode ’ s name and indication appear . They are displayed for approx. 2 seconds, then the name disappears so that only the indication remains.
EN 21 Digital Effects 1 Set the Power Switch to “ ” . 2 Press DIGIFECT repeatedly until the desired mode ’ s name and indication appear . They are displayed for approx. 2 seconds, then the name disappears so that only the indication remains. The mode is activated.
22 EN F E T O X O C P U O S S S C Y U A S R M T E E E R M A M M E E N A A N U U U U T T O O R D W S T D N E . I – A I R E C D V P S E X Z E H E P T T M O S L U S O O L A R Y D M E Y N S E N T G E T M H ME S 5 O O T F N P 0 F N 3 U U x F 0 LL R D W S T D N E .
EN 23 CAMERA MENU CONTINUED ON NEXT P AGE SYSTEM MENU This Menu Screen cannot be accessed while recording. MENU SCREEN EXPLANA TIONS D. ZOOM TITLE DA TE/TIME DISP . FOCUS EXPOSURE M.W .B. : Factory-preset WIDE REC MODE Refer to “ Focusing ” ( pg.
24 EN ON Records in S-VHS on a VHS or S-VHS cassette ( pg. 10). OFF Records in VHS on a VHS or S-VHS cassette ( pg. 1 0). Allows you to set the tape length depending on the tape used ( pg. 12). FULL Make all of the indications appear on the LCD monitor**/ viewfinder during playback or recording.
EN 25 25. 12. 01 25. 12. 01 22 : 25 : 00 22 : 25 : 00 25. 12. 01 (DATE) (TIME) (DATE/ TIME) AUTO DATE 1 Set the Power Switch to “ ” . 2 Press MENU . The Menu Screen appears. 3 Rotate MENU to select “ DA TE/TIME DISP . ” and press it. The DA TE/TIME DISP .
26 EN RECORDING Advanced Features (cont.) O 1 1 1 5 F / / F 4 2 S S S S REC T I ME O 1 3 1 5 F 5 0 F M M S S I I N N IN T . T IM E 1 1 5 S S MENU Wheel Recording Start/Stop Button REC TIME Menu Display Recording time indicator Interval time indicator INT .
EN 27 Exposure Control This feature automatically adjusts the iris for the best available picture quality , but you can override it and make the adjustment manually . Manual exposure adjustment is recommended in the following situations: • When shooting using reverse lighting or when the background is too bright.
28 EN Focus detection zone Focusing AUTO FOCUS The camcorder ’ s Full Range AF system offers continuous shooting ability from close-up to infinity . However, correct focus may not be obtainable in the situations listed below (in these cases use manual focusing): • When two subjects overlap in the same scene.
EN 29 Power Switch White Balance Adjustment A term that refers to the correctness of colour reproduction under various lighting. If the white balance is correct, all other colors will be accurately reproduced. The white balance is usually adjusted automatically .
30 EN 1 Load a tape ( pg. 13). 2 Set the Power Switch to “ ”. T o start playback, press 4 / 6 . •T o stop playback, press 5 . •Press 2 to rewind, or 3 to fast-forward the tape during Stop mode. NOTES: ● The camcorder shuts off automatically after about 5 minutes in Stop mode.
EN 31 Set to “ ” . TBC Button PLA YBACK Features COUNTER R/M Button Rewind ( 2 ) Button Fast-Forward ( 3 ) Button Play/Pause ( 4 / 6 ) Button Stop ( 5 ) Button T racking: Eliminates noise bars that appear on-screen during playback. Factory-preset is Auto T racking.
32 EN PLA YBACK Connections And T ape Dubbing A/V cable (provided) Yellow to Video Output Connector cover* T o TV or VCR Y ellow to V ideo Input B. Connection to a TV or VCR equipped only with A/V input connectors Use the provided A/V cable. White to Audio Output White to Audio Input Yellow: not connected A.
EN 33 Basic Connections 1 Make sure all units are turned off. 2 Connect the camcorder to a TV or VCR as shown in the illustration ( pg. 32). If using a VCR . . . go to step 3 . If not . . . go to step 4 . 3 Connect the VCR output to the TV input, referring to your VCR ’ s instruction manual.
34 EN PLA YBACK Using The Cassette Adapter Compact video cassette VCR Reels Compartment door Recording safety hole Sliding latch Cassette Adapter (provided with GR-SXM470A/FXM270A/FXM170A/FX220A/ FX120A/SXM27EA/SX22EA only) Use this to play back an S-VHS-C/VHS-C video cassette recorded with this camcorder on a VHS VCR.
EN 35 USING THE REMOTE CONTROL UNIT (GR-SXM470A only) The Full-Function Remote Control Unit can operate this camcorder from a distance as well as the basic operations (Playback, Stop, Pause, Fast-Forward and Rewind) of your VCR.
36 EN USING THE REMOTE CONTROL UNIT (GR-SXM470A only) (cont.) 1 3 2 + – + – I nstalling The Batteries The remote control uses two “ AAA (R03) ” size batteries. See “ General Battery Precautions ” ( pg. 52). 1 Open the battery compartment cover as illustrated.
EN 37 Press T Normal playback Remote sensor Playback Zoom T o magnify the recorded image up to 10X at any time during playback. NOTES: ● Use the remote control unit to perform this procedure. ● Make sure that the TBC mode is activated ( pg. 31).
38 EN w M – 0 : 12 : 34 PAUSE FF A.DUB STOP PLAY REW INSERT START/STOP Insert editing indicator Display COUNTER R/M Button T ape Counter Remote sensor Power Switch Insert Editing Y ou can record a new scene onto a previously recorded tape, replacing a section of the original recording with minimal picture distortion at the in- and out-points.
EN 39 M – 0 : 05 : e 2 4 0 PAUSE FF A.DUB STOP PLAY REW INSERT START/STOP Audio Dubbing Y ou can record a new soundtrack on a prerecorded tape. The existing original sound is erased and replaced by the sound from the built-in microphone. Perform steps 1, 2 and 3 of the Insert Editing procedure ( pg.
40 EN VCR CODE LIST 6 2 6 4 7 7 MITSUBISHI 6 7 6 8 NEC 3 7 3 8 GRUNDIG 1 4 3 4 HITACHI 6 6 6 3 PANASONIC 1 3 1 7 1 1 9 4 1 8 JVC 9 1 9 6 9 3 BLAUPUNKT AKAI 9 7 9.
EN 41 MAKE CONNECTIONS 1 JVC VCR EQUIPPED WITH REMOTE P AUSE TERMINAL Connect the editing cable to the Remote PAUSE terminal. JVC VCR NOT EQUIPPED WITH REMOTE P AUSE TERMINAL BUT EQUIPPED WITH R.A. EDIT CONNECTOR Connect the editing cable to the R.A.EDIT connector .
42 EN SELECT SCENES 4 Point the remote control at the camcorder ’ s remote sensor . Press PLA Y ( 4 ), then press R.A.EDIT ON/OFF on the remote control. The R.A. Edit counter display appears. 5 Press REW ( 2 ) or FF ( 3 ) to locate the beginning of the scene you want, then press EDIT IN/OUT to register that point.
EN 43 AUTOMA TIC EDITING TO VCR 9 Rewind the tape in the camcorder to the beginning of the scene you want to edit and press P AUSE ( 6 ). 10 Point the remote control towards the VCR ’ s infrared sensor and press VCR REC STBY ( q6 ), or manually engage the VCR ’ s Record-Pause mode.
44 EN I T E M S N O T E S ❍ Perform charging where the temperature is between 10 ° C and 35 ° C. 20 ° C to 25 ° C is the ideal temperature range for charging. If the environment is too cold, charging may be incomplete. ❍ Charging times are for a fully dischar ged battery pack.
EN 45 I T E M S N O T E S ❍ When the Power Switch is set to “ ” or “ ” and the LCD monitor is opened at an angle of 60 degrees or more, the LCD monitor switches on and the viewfinder switches off automatically to save power (models equipped with LCD monitor only).
46 EN TROUBLESHOOTING If, after following the steps in the chart below , the problem still exists, please consult your JVC dealer . The camcorder is a microcomputer -controlled device. External noise and interference (from a TV , a radio, etc.) might prevent it from functioning properly .
EN 47 SYMPTOM POSSIBLE CAUSE(S) OTHER During recording, the indications do not appear . The tape will not eject. Some functions are not available. V ertical white lines appear when shooting a very bright object. Bright, crystal-shaped spots appear in the LCD monitor and the viewfinder .
48 EN INDEX Controls, Connectors And Indicators I 2 1 3 5 6789 ! 0 yu Y U T Q W E R p i @ $ # % ^ * ( & t r w e q o ) @ 4.
EN 49 Controls 1 V ideo Light Switch [LIGHT OFF/AUT O/ON] (GR-SXM470A/FXM270A/FX220A/ SXM27EA/SX22EA only) ....................... pg. 17 2 Stop Button [STOP] .............................. pg. 30 3 • Retake Rewind Button [RETAKE R] ..... pg.
50 EN INDEX Indications 1 R 4 B 2 2 E 4 5 1 R 5 0 C 4 M / I . M I 2 G C 1 I S N S H O 2 N P 1 T N . S G 0 N – – R 1 I V P A G H A – T H S U – U T S – L S R E – A – 1 E – T E 0 C – I 1 T x – O 1 6 N : – S 4 T + M – 5 4 0 W – : 0 2 B 1 + 8 1X 7 9 0 ! @ $ % # 8 * & ^ 5 3 4 1 2 6 a b ( ) 1 T ape Remaining T ime .
EN 51 W ar ning Indications Indications Function Displays the battery remaining power . Remaining power level: high. It does not necessarily mean that the battery pack is fully charged. Remaining power level: exhausted As the battery power comes close to nil, the battery indicator blinks (battery power warning).
52 EN Video Light DANGER: • The video light becomes extremely hot. Do not touch it either while in operation or soon after turning it off, otherwise serious injury may result. • Do not place the camcorder into the carrying case immediately after using the video light, since it remains extremely hot for some time.
EN 53 Cassettes T o properly use and store your cassettes, be sure to read the following cautions: 1. During use . . . ... make sure the cassette bears the S-VHS-C or VHS-C mark. ... be aware that recording onto prerecorded tapes automatically erases the previously recorded video and audio signals.
54 EN For Y our Maintenance 1. After Use 1 Set the Power Switch to “ OFF ” to turn off the camcorder. 2 Open the LCD monitor to an angle of over 60 degrees. Slide EJECT to open the cassette holder , then remove the cassette. 3 Close and lock the cassette holder by pressing the Close button.
EN 55 Lens : F1.6, f = 3.9 mm to 62.4 mm, 16:1 power zoom lens with auto iris and macro control, filter diameter 40.5 mm V iewfinder : Electronic viewfinder with 0.5" black/white CRT White balance adjustment : Auto/Manual adjustment LCD monitor : 3" diagonally measured, LCD panel/TFT active matrix system (GR-SXM470A only) 2.
® Registered Trademark owned by VICTOR COMPANY OF JAPAN, LTD. COPYRIGHT© 2000 VICTOR COMPANY OF JAPAN, LTD. A/EA Printed in Malaysia 1000MKV * UN * PJ EN GR-SXM470A GR-FXM270A GR-FXM170A GR-FXM17A G.
Een belangrijk punt na aankoop van elk apparaat JVC GR-FX120A (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen JVC GR-FX120A heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens JVC GR-FX120A vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding JVC GR-FX120A leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over JVC GR-FX120A krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van JVC GR-FX120A bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de JVC GR-FX120A kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met JVC GR-FX120A . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
