Gebruiksaanwijzing /service van het product GY-DV500 van de fabrikant JVC
Ga naar pagina of 94
JVC D V CAMCORDER GY-DV500 Min i INSTRUCTIONS * The illustration shows the GY-DV500 D V Camcorder with the optional lens viewfinder attached. Thank you fo r purchasing this JVC product. Before operating this unit, please read the instructions carefully to ensure the best possible performance.
Thank you for purchasing the JVC GY-DV500 D V Camcorder. These instructions are for GY-DV500E. SAFETY PRECAUTIONS WARNING: TO REDUC E TH E RIS K O F FIR E OR ELECTRIC SHOCK, DO NO T EXPOSE THIS APPLIANCE T O RAIN OR MOISTURE. This uni t should b e use d with 12V D C only .
Min i This uni t i s a MiniD V video system format camcorder. Videocassettes which are not marked wit h the MiniDV symbol cannot b e used with this unit. The following phenomena ma y occur when tapes recorded on other unit s (including another GY-DV500) are recorded or played back on this camcorder.
CONTENTS 5 . PREPARATIONS MAIN FEATURES........................................................ . 3 1 . INTRODUCTION 1- 1 1- 2 1- 3 1-4 1-5 1-6 1- 7 Main Uni t Configuration............................................. . Precautions for Proper Use ...
11 . USING EXTERNAL COMPONENTS 11- 1 11- 2 Connecting a Video Component with D V Connector Connecting a PC..................................................... . 64 6 5 12 . SETUP MENU 12- 1 12-2 12-3 12-4 12-5 12-6 12-7 12-8 12-9 12-10 12-1 1 VCR Setup Menu .
1 . INTRODUCTION Th e GY-DV500 configuration i s a s shown below . CAUTION : • The front base mount may b e locked while the pi n of the tripod base i s not inserted into th e hol e o n th e rea r bas e moun t of the unit. Therefore, after mounting, make sure that these parts are engaged properly.
1 . INTRODUCTION • When the uni t i s no t i n use , b e sure to set the POWER switch • The camera ma y b e unstable i n the period immediately after to OFF i n order to reduce power consumption, the power i s turned on, but this i s no t a malfunction.
1 . INTRODUCTION • Use JVC's Videocassette tapes marked with MiniDV for this unit. Please us e DVM60 or DVM30 type videocassettes. • Videocassettes cannot b e used upside down • Avoid storing a Videocassette with unevenly wound tape, as this may damage the tape.
1 . INTRODUCTION Smear and Blooming Du e t o the physical structure of a CCD i t i s possible to induce vertical streaking (calle d "smear") when shooting a n extremely brigh t ligh t source. Another effect i s the expansion o f ligh t around a bright ligh t or object (called "blooming").
2 . CONTROLS, INDICATOR S AND CONNECTOR S [ZEBRA] Switch Viewfinder mount base, sliding securing ring Mount the Viewfinder on the base an d secure i t using the slidin g securing ring. See "Attaching the Viewfinder" o n pag e 31 . [VF] Viewfinder connector (6-pin) Connect the cable from the viewfinder here.
2 . CONTROLS, INDICATORS AND CONNECTORS CAUTION: • As the automatic shutter i s activated here, flicker ma y appear on th e scree n depending on the lighting conditions (such as a fluorescent lamp, etc.) • This operation i s not possible i n the LOLUX mode .
2 . CONTROLS, INDICATORS AND CONNECTORS [Camera Setting Section] [ALARM] Volume control Turn to adjust the volume of the alarm tone that i s output from the monitoring loudspeaker or earphone i n case o f a warning or other abnormal condition occurring with the GY- DV500 .
2 . CONTROLS, INDICATORS AND CONNECTORS [AUTO IRIS] Auto iris level switch Thi s switc h select s th e automati c iris adjustmen t reference value according to th e conditio n i n which th e camera i s used . BACK. L : Under back light (Opens the iri s abou t 1 step from the standard level.
2 . CONTROLS, INDICATORS AND CONNECTORS [Audi o Setting Section] CAUTION: Make sur e to move switches al l the way . Do no t leave a switc h stoppe d i n a midwa y position .
2 . CONTROLS. INDICATORS AND CONNECTORS [VCR Setup Block] 0 [MENU] butto n Press this button t o enter the VCR setup menu mode . When the VCR setup menu mode i s engaged, the "MENU" indicator i n the LCD display lights and the counter display and viewfinder displa y are changed to the menu indication.
2 . CONTROLS, INDICATORS AND CONNECTORS [VCR Display Section] [OPERATE/WARNING] indicator Normally lights green. Lights orange during the VTR SAVE (tape protect) mode . This indicator light s or blinks i n re d i n the case of a warning condition related to the remaining tape time, remaining battery power or other abnormal condition i n the unit.
2 . CONTROLS. INDICATORS AND CONNECTORS Tape transport direction indicators ^BEV FWD^ One of the indicators lights according to the tape transport direction. i s displayed i n the record-pause mode an d i n the stil l picture mode. Remaining Battery Power Display Th e 7-dot segmen t ba r displa y shows the remainin g batter y power.
2 . CONTROLS, INDICATORS AND CONNECTORS Cassette cover Pressing the EJECT switch o n top o f the section opens this cover so that a videocassette can be inserted or removed fro m the unit. The cover can be locked automatically b y pushing and closing it .
2 . CONTROLS, INDICATORS AND CONNECTORS [EJECT] switch Slid e t o th e sid e whe n insertin g o r ejectin g th e videocassette. Sliding this switch opens the cassette cover . I f the switch i s moved while the power i s off , the cassette cover opens but i t i s not possible to inser t or eject the cassette.
2 . CONTROLS, INDICATORS AND CONNECTORS [DV] connector Using a D V cable (optional), a digital video component with D V connector can b e connected here. This connecto r is used fo r output of the D V signal or to input th e VC R contro l signa l fro m the digita l vide o component with D V connector.
2 . CONTROLS, INDICATORS AND CONNECTORS [CH- 2 AUDIO IN ] CH- 2 audi o inpu t connector (XLR 3-pin) Connect the external audio equipment or microphone to this connector. Set the CH-2 AUDIO I N LINE/MIC select switch according to the connected equipment.
2 . CONTROLS, INDICATORS AND CONNECTORS COUNTER switch Counter displa y Remaining Tape Time Display This display shows the remaining tape time (minutes/seconds) i n record and pla y modes. • Example : 3 0 minutes of remainina taoe . • Thi s indicator blink s when remainin g tape tim e i s equivalen t to less than 2 minutes.
2 . CONTROLS. INDICATORS AND CONNECTORS [S14x7.3B12 ] IRIS mode switch A: Activates the auto iris feature. M : Allows manua l iri s control. Momentary auto iris button When the IRI S MODE switch 0 i s a t "M", pushin g thi s butto n activates the Auto Iris Function while i t i s hel d down only .
2 . CONTROLS, INDICATORS AND CONNECTORS [VF-P115B] Stopper screw This screw prevents the viewfinde r from coming of f th e camera. Mounting guid e T o attach on the camera.
2 . CONTROLS, INDICATORS AND CONNECTORS WARNING LED INDICATORS INSIDE THE VIEWFINDER BAT T Lam p REG/ALARM Lam p Th e viewfinde r ha s two LE D indicator s belo w the screen. Thes e LEDs ligh t or blink t o indicate the present status o f th e camer a or the VCR.
2 . CONTROLS, INDICATORS AND CONNECTORS 2- 9 Indication s inViewfinder(Cont'd ) ®- .( D . ® ACCU-FOCUS— — G—— F— — ———L.......
2 . CONTROLS, INDICATORS AND CONNECTORS • Status 1 I n addition to the information on the Statu s 0 screen, this screen displays audio indicators and informatio n o n remainin g tape , voltage an d lens F-number. Status 2 This screen displays the camera setup statuses.
2 . CONTROLS, INDICATORS AND CONNECTORS Alarm Message Displa y The following alarm messages are displayed on the status 0 and status 1 screens . Indicatio n LO W BATTERY CLOSE CASSETTE COVER VTR WARNI.
2 . CONTROLS. INDICATORS AND CONNECTORS Safety Zone Three types o f safety zone items can b e displaye d i n the viewfinder. Select th e require d on e with th e SAFETY ZONE ite m o n th e VF DISPLAY menu screen. OF F ZONE1 ZON E 2 ZONES Setting the Screen Displa y Screen used for making various setting s o f th e camer a an d VCR.
3 . BASI C SYSTEM CONNECTION S AND ADJUSTMENTS 3- 1 Basi c Syste m Fo r information on connection with the individua l attachments, refer to the page explaining the respective connection methods. * HZ-FM 1 3 cannot be used with S14X7.3B12/U. Please use the Focus Manual Uni t (FMM-8, CHF-3, CFC-12-990) manufactured by Fujinon.
3 . BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS 1. Loosen the moun t ring . 2. Connect the cabl e connector. 3. Attach th e len s with it s pi n aligne d with th e hol e i n th e mount . 4. Tighte n th e moun t ring . Be sure to tighten the mount ring completely.
3 . BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS Provided Microphone Connecting the provided microphone to the viewfinder. The provided microphone i s a phantom microphone. 1.3. I. Loosen the stopper screw o n the viewfinder. 2..Attach the microphone to th e attachment guide on the viewfinder a s illustrated .
3 . BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS 1. Tripo d mountin g hole s Us e the provided tripod bas e to place the camera o n a tripod. 1. 2. 3. Attach the tripod base on the tripod b y usin g the hol e that balances the uni t most optimally .
3 . BASIC SYSTEM CONNECTIONS AND ADJUSTMENTS The GY-DV500 uses a lithium battery for backu p of th e tim e code data an d time date data . Instal l the provided lithium battery before actually using the unit .
4 . POWER SUPPL Y Th e GY-DV500 i s operable with AC power supply or battery pack . Use the JVC AA-P250 AC power adapter (max. rate d output 12. 5 V DC , 3.5 A) a s the AC power supply . DC cable AC power adapter Note : D o no t remove or connect the D C cable while recording i s being performed.
4 . POWER SUPPL Y Attaching a Fla t Shape Type Battery Pac k Loc k release lever Open th e batter y cas e cove r whil e pushin g the loc k releas e lever . Inser t the battery pac k int o the batter y case with it s electrodes facing the unit . Close the battery case cover .
4 . POWER SUPPL Y Using a n Anton-Bauer Battery Pack T o use a n Anton-Bauer battery pack (Propack 13/14, Tnmpac k 13/14, Magnum 13/14, Compack 13/14 Series), i t i s necessary to detach the battery case from the GY-DV500 and replace i t with the Anton-Bauer battery holder.
4 . POWER SUPPL Y REMAINING BATTERY POWER DISPLAY WARNING indicato r Viewfinder BAT T lam p • T o display the remaining battery power accurately, set the VCR Setup Men u ite m No . 396 BATTERY TYPE according to the type of the battery pac k i n use .
5 . PREPARATIONS 2. VTR switch 1. POWER switch Turn the POWER switch to ON • The power i s then supplied to the unit . • Video image i s output to the viewfinder. • The displa y of the VCR section i s turned on . Select the GY-DV500 operation mode with the VTR switch.
5 . PREPARATIONS Cassette rear switch - Videocassette Cassette cove r A cassette cannot b e loaded or unloaded while the GY-DV500 i s i n POWER OF F mode . Use a videocassette tape marked MiniDV . The videocassette should b e held vertical and inserted straight into the slot.
5 . PREPARATIONS Th e date and tim e o f the built-in clock should b e set . During shooting, the date an d time data are recorded i n th e sub-time code area o n the tape.
6 . SETTIN G AND ADJUSTMENTS BEFOR E SHOOTING 1. , POWER ON Firs t place a charged battery pac k i n the battery case o n the rear section of the unit I f battery pack i s not used, connect D C power .
6 . SETTING AND ADJUSTMENTS BEFORE SHOOTlMft Eyepiec e 2. Eyepiece focusing rin g 3 . 3 . CON T BRIGH T Adjust the position and angle of the viewfinder. Diopter adjustment Rotate the eyepiece focusing ring unti l the viewfinder screen image i s clearly visible.
6 . SETTING AND ADJUSTMENTS BEFORE SHOOTING I t i s only necessary to perform this when the lens is attached fo r the firs t time or when focusin g i s not correc t i n both the telephoto and wide-angle positions. Adjust the viewfinder fo r sharpness first.
6 . SETTING AND ADJUSTMENTS BEFORE SHOOTING 6- 5 White Balanc e Adjustmen t Since the colour of light (colour temperature) varies depending o n the ligh t source, i t i s necessary to re-adjust the white balance When the main ligh t source illuminating the subject changes.
6 . SETTING AND ADJUSTMENTS BEFORE SHOOTING Audio inpu t signal selection Use the AUDIO INPUT switch to select whether the sound recorded on audio channel 1 or 2 i s th e sound fro m the microphone connector on the front section o r the sound from the AUDIO INPUT connector on the rear section.
6 . SETTING AND ADJUSTMENTS BEFORE SHOOTING Microphone inpu t connector CH-1 AUDIO LINE/MI C switc h CH-1 AUDI O INPU T connector CH-2 AUDIO LINE/MIC switch CH- 2 AUDIO INPU T connecto r The GY-DV500 i s provided with the microphone connector on the front section and the two AUDIO INPU T connectors a t the rear section for audio input.
6 . SETTING AND ADJUSTMENTS BEFORE SHOOTING CH- 2 Audi o selec t switch CH- 1 recording leve l contro l Fo r each audio channel, us e the AUDIO SELECT switches to select whether the recording leve l adjustment should b e set to AUTO mode or MANUAL mode .
6 . SETTING AND ADJUSTMENTS BEFORE SHOOTING EARPHONE jack MONITOR SELECT switch Monitoring loudspeaker ALARM control MONITOR control Th e audio inpu t during recording, i n record-pause or sto p mode can be monitored throug h the monitorin g loudspeaker or earphone.
7 . SHOOTIN G OPERATION 1. "DEW" 1. Set the POWER switch to ON . Power i s supplied to the unit . Check that the condensation indicator "DEW" does not appear o n th e display . I f i t i s lit , wait unti l the indicato r goes out.
7 . SHOOTING OPERATION 8. 9. 10. VTR trigger button 8. Press the VTR trigger button on the GY-DV500 or len s to start recording. Once recording ha s started, th e BACK TALLY lam p o n th e rea r section o f the unit and the tally lamp o n the viewfinder light red, and the REC indication i n the viewfinder lights green.
7 . SHOOTING OPERATION Viewfinder VCR operation status displa y STBY or SAVE When a recordable videocassette is loaded, the GY-DV500 enters the record-pause mode. However, the record-pause operation condition differs dependin g on the setting o f the VTR switch .
7 . SHOOTING OPERATION RET button * This functio n does not work when the GY-DV500 is i n the save mode or stop mode . * During recording check, the following indications wil l appear i f the error rate increases due to head clogging, etc. • "RF" appears on the display panel .
8 . PLAYBACK MOD E 2. 2. EJECT switch 4. STIL L butto n 6. STOP button - 3. 5. PLAY button 1. POWER switch Operation Set the POWER switch to ON . Load the recorded videocassette correctly. • Slide the EJECT switch to the side. When the cassette cover opens, insert the videocassette and then close the cassette cover again.
8 . PLAYBACK MOD E REW button F F button STO P butto n Press the F F button i n stop mode to fast forward the tape . Press the REW button i n sto p mode to rewind the tape.
9 . TIME COD E OPERATION Th e GY-DV500 records EBU-standard time codes and user's bits . I n the pla y or record mode, the reproduced time codes o r user' s bits are shown on the counter display . • Time code dat a cannot b e output through the unit' s connectors.
9 . TIME CODE OPERATION TIME CODE PRESETTING PROCEDURE 2. HOLD button 4. SHIFT butto n 6. 'PRESET button 3. ADVANCE - button 1 . Display the time code on the counter display . Se t the COUNTER switch t o "TC". • Time code u p t o 23 hrs .
9 . TIME COD E OPERATION Th e GY-DV500 also incorporates a time code reader Therefore, when the unit enters record mode from record-pause mode , i t can read the time code data recorded on the tape and record time codes i n continuation of the existing data.
9 . TIME CODE OPERATION The GY-DV500 incorporates a time code reader. During playback , th e time code or user's bi t data recorded o n the tape i s displayed o n th e counter display . Set the VCR Setup Men u ite m No . 516 DISPLA Y SELEC T to "TC".
10 . S.S.F . (Supe r Scen e Finder ) FUNCTIO N During recording, the S.S.F . function records the time code data a t the point of time of a desired recorded scene i n the unit's memory. Using the S.S.F . data stored i n memory during after-processing of the recorded image allows efficient us e of the tape.
10 . S.S.F . (Supe r Scene Finder ) FUNCTION VTR trigger button TAKE button CUE Mode MARK Mode 1. Set the S.S.F . mode as CUE mode. Set the VC R Setup Menu item No . 398 S.S.F . MODE to "CUE". See page 69 . • The CUE mod e i s indicate d i n the lowe r par t of th e Status 1 screen i n the viewfinder.
10 . S.S.F . (Supe r Scen e Finder ) FUNCTIO N The S.S.F . data recorded i n the unit' s memory can b e deleted i n the record mode and the record-pause mode . This function i s only valid i n the MARK mode . I n the record mode, press the N G button after the I N poin t ha s been stored or after the scene ha s been stored.
10 . S.S.F . (Supe r Scen e Finder ) FUNCTIO N S.S.F . data stored i n the unitis memory can b e written to the beginning of tape. Precautions when writing S.
11 . USIN G EXTERNAL COMPONENT S Rear section of GY-DV500 Video component with DV Connector DV connector DV connector DV cabl e Connection Connect th e D V connecto r on the GY-DV500 t o th e DV connecto r o n th e video component using th e D V cable .
11 . USIN G EXTERNAL COMPONENTS D V connector Connections Connect the GY-DV500's VTR REMOTE connector to the RS-232C connector on the P C or the non-linear editin g controller using the TTL < > RS-232C converter cable.
12 . SETU P MEN U Th e setup menus for the VCR section can b e set while observing the menu i n the viewfinder and on the unit's counter display . The set contents are stored i n the memory an d retained even after th e power i s switched OFF . VCR SETUP MENU CONFIGURATION Th e VCR Setup Menu i s a two-layer construction.
12 . SETUP MEN U DISPLAYING AND SETTING VCR SETUP MENUS "MENU" indication Viewfinder 1. Engaging the VCR Setup Menu mode. Press the MENU button. • The "MENU" indication i n the display section starts blinkin g and th e VC R Setu p Menu appears i n the viewfinder an d o n the counte r display .
12 . SETUP MEN U VCR SETUP MENU CONTENTS Item Factory Setting Grou p Contents (Upper row: Viewfinder display Lower row: Counter display indication SERVO /SYSTEM AUDI O 050 : REMOTE SELECT rnS L 082: B.
12 . SETUP MEN U Grou p Settin g Valu e Ite m Factory Settin g Contents Upper row: Viewfinder display Lower row: Counter display indication SYSTEM ON SCREEN 307 : LONG PAUSE TIME LGP t 396: BATTERY TYPE bAt t 398: SSFMODE SS F 516: DISPLAY SELECT dS P 3MIN 30MIN 0 3 3 0 12 V 13.
12 . SETUP MEN U Camera Menu Screen Flow As illustrated below, the Camera Menu i s a men u screen comprising several layers . The first laye r o f th e CAMERA MENU screen i s for choosing and setting the menus required i n accordance with functions or purposes.
12 . SETUP MEN U | STATUS butto n 2. 3. 4. 5. 6. 8. SHUTTER dial CURSOR Item Settinq value CAMERA MENU screen Ite m Settin g valu e VF DISPLAY MENU screen Return to the CAMERA MENU screen. Turn the SHUTTER dia l u p or down to alig n the cursor with the PAGE BACK item , and the n press th e SHUTTER dia l i n the direction of the arrow.
12 . SETUP MEN U Ite m FNO. DISPLA Y AUDIO DISPLAY SAFETY ZONE RECTIME ZEBRA PAG E BACK Function , Operation Selects whether or not the F-number o f the lens iris i s displayed on the Statu s 1 screen. O N ....................... . F-number i s displayed.
12 . SETUP MEN U Ite m SHUTTER FA W GAIN L GAIN M GAIN H SMOOTH TRANS PAG E BACK Function , Operation Th e SHUTTER butto n on the right side section i s used to select STEP for fixed shutter speed orV.SCAN variabl e scannin g rat e for shooting computer monitor screens.
12 . SETUP MEN U Ite m MASTER BLACK DETAI L DTL.V/H BAL DTL . FREQUENCY SKI N DT L DETECT V . RESOLUTION ADVANCED PROCESS PAG E BACK Function , Operatio n Adjusts the pedestal leve l (master black) , which i s th e reference of black . •T o increase the pedestal level.
12 . SETUP MEN U Ite m COLOR MATRIX GAMMA SKIN COLOR ADJUST PAGE BACK Function , Operation Sets the colour matrix OFF...... Deactivates the colour matrix function O N .
12 . SETUP MEN U The uni t ha s three files tha t can b e used for storing camera menus. The FIL E MANAGE screen i s for performing the operations for saving the set CAMERA MENU . • When menu settings are made using SCENE FIL E A or B , the contents of the settings wil l b e invali d i f th e storage operation s are not performed on this screen.
12 . SETUP MEN U Ite m H PHASE S C PHASE CAM MI C +48V PAG E BACK Function , Operation Fo r adjusting the horizontal phase of the unit i n relation to the signal (external sync signal) input through the SYNC I N connector on the left side of the unit.
12 . SETUP MEN U Usin g the FIL E MANAGE screen, the CAMERA MENU settings can b e reset to the initial setting values. On the FIL E MANAGE screen, select the file of the CAMERA MENU to b e reset, and then perform the resetting operation. 2 . 3 . 4 . 5 .
13 . FEATURES OF THE CAMERA SECTION The FA W function adjusts the white balance value automatically as the lighting condition changes. This mode i s convenient when you have n o time to adjust the whi.
13 . FEATURES OF THE CAMERA SECTION ADJUSTMENT OF LENS IRIS The lens iris can b e adjusted using any of the following three methods. Temporary aut o iri s button Iri s mod e switch • Automatic adjustment Set the iris mod e switch to "A " (Auto).
13 . FEATURES OF THE CAMERA SECTION 13- 3 Shootin g th e Scree n Imag e o n a Compute r Moo|^^^ r Ban d Video monitor Outline The following operation allows the alignment of the shutter speed of the camera with the variable scanning rate of a computer monitor or display .
13 . FEATURES OF THE CAMERA SECTION Th e gai n should b e switched when the brightness i s insufficient due to poor lighting conditions . GAIN SWITCHING GAI N switc h CAUTION: When gain i s set to "ALC", gain i s boosted automatically a s the illumination becomes darker.
13 . FEATURES OF THE CAMERA SECTION Various switch settings are performed to accommodate th e conditions o f the illumination and the subject when shooting.
13 . FEATURES OF THE CAMERA SECTION 13- 6 Ho w t o Us e Ski n Detai l Th e contour emphasis i n the skin colour areas of the video signa l can b e controlled and mad e to appear gentle and smooth. PROCESS screen ADVANCED PROCESS screen SKIN COLOR ADJUST screen Pres s th e STATU S butto n fo r abou t 1 secon d to displa y th e CAMERA MENU screen.
13 . FEATURES OF THE CAMERA SECTION Confirming the colour tone area adjusted with the Skin Detai l function When the ZEBRA switch o n the front section i s pressed to the "SKIN AREA " side, the colour tone areas adjusted with Skin Detai l are displayed i n the viewfinder.
14.OTHERS Warnings concerning problems with the unit are provide i n the form of indicators, displa y indications an d monitor tones. The warnings are of the following two types.
14.OTHERS Alarm Indications (Cont'd) Depending on the alarm conditions, the warning indicators i n the LCD display , the WARNING indicator, the TALLY lamp , alarm tones and the viewfinder appea r as shown i n the following table. The WARNING indicator normally light s green or orange to indicate that operation i s possible .
14.OTHERS WARNINGS I N VIEWFINDER Viewfinder Warning Lamps REG/ALARM lamp Batter y lam p 1. BATTERY lamp This red lamp light s under the following circumstance. Light s re d : • When the battery voltage becomes to o lo w for the camera to operate. 2.
14 . OTHERS I n the case of troubles occurring during operation of the GY-DV500, i t performs a self-test to identify the cause and displays the resul t i n the form of a n error code. The error code consists of the "main code" which indicates it s contents an d the "sub-code" which indicates the details.
14.OTHERS TROUBLES WITH ERROR CODE OUTPUTS Error Cod e 3200 3300 4000 4100 420 0 560 5 5606 to 5607 570 2 5802 700 1 710 1 7202 t o 720 3 730 2 to 730 3 730 5 Error Detail s Tape loading impossible. Tape unloading impossible . Irregular cassette intake operation.
14 . OTHERS TROUBLES WITHOUT ERROR CODE OUTPUTS Symptoms Power cannot b e switched ON . Operation buttons o n the GY-DV500 don't work. Recording i s no t possible. Noise interferes with playbac k video . Sound and picture are disturbed during playback.
14.OTHERS Th e uni t can display the accumulated runnin g time of th e hea d drum a s hou r meter data o n the counter displa y The hour meter ca n b e displayed b y selecting H M (HOUR METER) on the .
14.OTHERS CAMERA SECTION Image picku p devices: 1/2-inc h interline CCD x 3 Colour separation optical system: F1.4 3-colour separation prism Number of effective pixels: 440,000 pixel s ((H ) 752 x (V ) 582 ) Colour system Colour bar s Sync system Len s moun t Optical filter Sensitivity Minimu m illumination : Gain Shutter spee d V.
14.OTHERS OPTIONAL ACCESSORIES Viewfinder Powe r zoo m len s AC power adapter Microphone Microphone holder : VF-P115B,VF-P116 : S14 x 7.3B12, S16 x 6.7B12, S1 9 x 6.5B1 2 (FUJINON ) YH14 x 7.3K12, YH18 x 6.7K12 (CANON) : AA-P250 : MV-P615 : KA-A50 EXTERNAL DIMENSIONS (unit: mm ) * Design and specifications are subject to change without notice .
Een belangrijk punt na aankoop van elk apparaat JVC GY-DV500 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen JVC GY-DV500 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens JVC GY-DV500 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding JVC GY-DV500 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over JVC GY-DV500 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van JVC GY-DV500 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de JVC GY-DV500 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met JVC GY-DV500 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
