Gebruiksaanwijzing /service van het product nxd-700vi van de fabrikant AMX
Ga naar pagina of 226
Operation/Reference Guide Touch Panels NXD-700Vi 7" Modero ® Wall/Flush Mount Touch Panel with Intercom Last Revised: 4/1/2011.
AMX Limited Warranty and Disclaimer This Limited W arranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partn er which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity .
AMX Software License and Warranty Agreement • LICENSE GRANT . AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this License. The AMX Software is licensed, no t sold. This license does not grant Licensee the right to create derivative wor ks of t he AMX Software.
FCC Information This device complies with Part 15 of the FCC Rules. Operati on is subject to the fol lowing two condition s: (1) this device may not cause harmful interference, and (2) this device must accept any interference rece ived; in cluding in terference that may cause undesi red operation.
Table of Contents i NXD-700Vi 7" Modero® Wall/Flush Mo unt Touch Panel with Intercom Table of Contents Introduction .................. ...................................................................... ................ 1 Common Applicati on.
ii NXD-700Vi 7" Modero® Wall/Flush Mount Tou ch Panel with Intercom Table of Contents Ethernet/RJ-45 Port: Connections and Wiring ................... .................... ................. 37 USB Port: Connecting and Using Input Devices ........
Table of Contents iii NXD-700Vi 7" Modero® Wall/Flush Mo unt Touch Panel with Intercom Step 3: Confirm an d Upgrade the firmw are via the USB port ........ ................ ............... 65 Upgrading the Modero Firmware via Et hernet (IP Address) .
iv NXD-700Vi 7" Modero® Wall/Flush Mount Tou ch Panel with Intercom Table of Contents Checking imag e cache status .... ............. ............. ................ ............. ................ ........... 116 Password Setup Page .............
Table of Contents v NXD-700Vi 7" Modero® Wall/Flush Mo unt Touch Panel with Intercom @PHT .................. ............ ............ ............ ........... ............... ............ ............ ........... ........ .... ........ 136 @PPA .
vi NXD-700Vi 7" Modero® Wall/Flush Mount Tou ch Panel with Intercom Table of Contents ^BSO .............. ........... ............ ............... ............ ........... ............ ............... ............ ......... .. ......... 155 ^BSP .
Table of Contents vii NXD-700Vi 7" Modero® Wall/Flush Mo unt Touch Panel with Intercom ADBEEP ....................... ............ ............... ........... ............ ............ ............... ........... .......... .. ........ 172 ?TXT .
viii NXD-700Vi 7" Modero® Wall/Flush Mount Tou ch Panel with Intercom Table of Contents ^BBR ... ............ ........... ............... ............ ............ ........... ............... ............ ............ ........ ...... ...... 182 ^RAF .
Table of Contents ix NXD-700Vi 7" Modero® Wall/Flush Mo unt Touch Panel with Intercom ?PHN-LINESTATE ........... ............ .............. ............ ............... ............ ............ .............. ........... ... 189 ^PHN-PRIVACY .
x NXD-700Vi 7" Modero® Wall/Flush Mount Tou ch Panel with Intercom Table of Contents.
Introduction 1 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Introduction The NXD-700V i is an incredibly versatile user interf ace, combining a sleek, co mpact size, W all/Flu.
Introduction 2 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom These Color V ideo (CV) panels display NTSC/P AL/SEC AM video formats within variable sized windo ws.
Introduction 3 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom The NXD-700V i comes with a standard silver bezel (FIG. 1), b ut the de vice is also av ailable with the optional Mystique-style bezel (FIG.
Introduction 4 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom NXD-700Vi Specifications The following table outlines th e specifications for the 7" W i descreen Modero panels. Product Specifications Dimensions (HWD): • NXA-RK7: metal rack-mount with black matte finish: (4 RU - rack units high) 6.
Introduction 5 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Product Specifications (Cont.) Side Panel Components: Front setup access button: • Provides both access to the Setup and Calibration page and toggles the panel between a "sleep" or "wake" state.
Introduction 6 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Product Specifications (Cont.) Operating / Storage Environment: • Operating T emperature: 0° C (32° F) to 40° .
Introduction 7 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom NXD-700Vi Panels - Connector Layout FIG. 4 sho ws the layout of the connectors (located on the re ar of the base on the NXT and on the left side panel of the NXD panels).
Introduction 8 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom.
NXA-AVB/ETHERNET Breakout Box 9 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom NXA-AVB/ETHERNET Breakout Box The NXA-A VB/ETHERNET Brea kout Box (FIG. 5) is incl uded as part of the NXD -700V i Kit configuration ( panel and box ) but can be purchased as a separate access ory .
NXA-AVB/ETHERNET Breakout Box 10 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Installing the NXA-AVB/ETHERNET A 12 VDC-compliant power supply can indirectly pro v ide po wer to a Modero panel by routing po wer through the NXA-A VB/ETHERNET Breakout Box.
NXA-AVB/ETHERNET Breakout Box 11 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Wiring the NXA-AVB/ETHERN ET Connectors And Cables The inputs and outputs on the breakout box are separated into front and rear connect ors. The rear connectors are used to input external signals.
NXA-AVB/ETHERNET Breakout Box 12 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Wiring the NXA-AVB/ETHERNET for Unbalanced Audio Most domestic audio equipment has unbalanced audio inputs and outputs.
NXD-700Vi Touch Panel Accessories 13 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom NXD-700Vi Touch Panel Accessories Overview The following section outli nes and describes the othe r AMX equipment av ailable for these touch panels.
NXD-700Vi Touch Panel Accessories 14 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom NXA-WC80211GCF 802.11g Wireless Card (FG2255-07) These panels can also connect to a wireless network using the ( optional) 802.11g W i-Fi CF card.
NXD-700Vi Touch Panel Accessories 15 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom This card works with compatible 802.11b/g W ire less Access Points s uch as the NXA-W AP200G ( which uses a default SSID of AMX ).
NXD-700Vi Touch Panel Accessories 16 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom NXA-WC80211GCF Spec ifications (Cont.) Network Architecture: • Infrastructure mode (Client-to-Access Point) Operating Channels: • Using 802.
NXD-700Vi Touch Panel Accessories 17 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom NXA-WC80211GCF Spec ifications (Cont.) T ransmit Out put Power: • 802.
NXD-700Vi Touch Panel Accessories 18 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom.
NXA-CFSP Compact Flash (FG2116-7x) 19 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom NXA-CFSP Compact Flash (FG2116-7x) Overview Every NXD-700V i Modero panel is shipped with a 128 MB Compact Flash card (NXA-CFSP).
NXA-CFSP Compact Flash (FG2116-7x) 20 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom.
Installation and Upgrade of the Inter nal NXD Components 21 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Installation and Upgrade of the Internal NXD Components Overview Upgra.
Installation and Upgrade of the Inter nal NXD Components 22 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 6. Carefully lift-of f the back box housing and angle it ov er to the side of the unit where the wires are connected to the circuit board.
Installation and Upgrade of the Inter nal NXD Components 23 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 6. T o complete the upgrade process, either upgrade the re maining wir.
Installation and Upgrade of the Inter nal NXD Components 24 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom.
Installation 25 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Installation Overview NXD-700V i panels are installed into either a pre-w all surface (using a CB-TP7 conduit/w allbox) or a solid surface (using either solid surface or drywall scre ws).
Installation 26 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 5. From along the internal surface of the Faceplate, r emov e the six b u ttons by gently bending each Button latch up and pulling the b utton outwards.
Installation 27 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 5. From along the internal surface of the Faceplate, instal l the six b uttons by fi rmly inserting them into the button open ings until the Button latch secures the button in place (FIG.
Installation 28 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Pre-Wall Installation of the Conduit Box W all Mount panels (NXDs) are contained within an outer housing (back box). This back box is not remov ed when installing the NXD into a Con duit Box (CB-TP7).
Installation 29 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 4. Thread the incoming power , RJ-45 audio/video, Ethernet, and USB wiring through the knockouts ( use of the left wiring knock out s are recommended wit h this installation ).
Installation 30 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 5. Disconnect the terminal end of the power cable from the connected power supply . 6. Carefully slide the main NXD-700V i unit ( B in FIG. 12) into the conduit box, so that all Mounting T abs lie flush against the conduit box ( C in FIG.
Installation 31 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 3. Remove the F aceplate/bezel ( A in FIG. 14) from the main NXD unit ( B in FIG.
Installation 32 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 8. Install the three sets of drywall screws and e xpansio n clips into the three ov al notch lo cations along both sides of the main unit ( B in FIG.
Installation 33 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Installing the NXD into a Fl at Surface using #4 screws Mounting scre ws (#4-40, includ ed) are secur ed through two sets of circul ar holes located at the left and right sides of the NXD-700V i.
Installation 34 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 7. Disconnect the terminal end of the power cable from the power supply . 8. Carefully slide the main unit into the cutout un til the Mounting T abs of the NXD-700V i unit lie flush against the wall.
Installation 35 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 4. T est the incoming wiring by connecting the panel connect ions to their terminal locations and applying power . V erify that the panel is rece iv ing po wer a nd functioning properly to pre vent repetition of the installat ion.
Installation 36 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Wiring a Power Connection T o use the 2-pin 3.5 mm mini-Phoen ix connector with a 12 VDC-complia nt po wer supply , the incoming PWR and GND wires from the external source must be connected to their co rresponding locations on the connector (FIG.
Installation 37 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Ethernet/RJ-45 Port: Connections and Wiring FIG. 18 describes the blink activity for the Ethernet 10/100 Base-T RJ-45 connector and cable. The Ethernet cable is connected to the rear of T able T op and side of the W all Mount panels.
Installation 38 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom If a USB mouse has been connected, a mouse cursor appears on the panel screen and its location corresponds to the mouse cursor posit ion sent by the external USB mouse.
Panel Calibration 39 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Panel Calibration Overview This section outlines the steps fo r calibrating the touch panel. It is r ecommended that you calibrate the panel befor e its initial use and after completing a firmwar e download.
Panel Calibration 40 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Testing your Calibration 1. Press and hold down the on-screen Calibration b utton for 6 seconds to enter the Calibration T est page (FIG. 23). 2. Press anywhere on this page to confirm the on-screen crossh airs match your touch points.
Configuring Communication 41 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Configuring Communication Overview Communication between the Modero panel and the Master is done using either USB or ETHERNET ( DHCP or Static IP ).
Configuring Communication 42 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Setting the Panel’ s Device Number In the Pr otected Setup page: 1.
Configuring Communication 43 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Configuring a Wireless Network Access When working with a wire less card, the f irst step is to conf igure wireless comm unication parameters within the W ireless Settings page.
Configuring Communication 44 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Security Settings section on page 46 f or detailed procedures to setup either a secure or unsecure connection. Wireless communic ation using a Static IP Address In the Pr otected Setup page: 1.
Configuring Communication 45 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom If a W AP is displayed in the list is not detected for 10 scans in a ro w it is then remov ed from the screen. In this way , a user can walk ar ound a building and see access points come and go as they mo ve in and out of range.
Configuring Communication 46 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Step 2: Configure the Card’s Wireless Security Settings The second step to successfully setting up your wireless ca rd is to configure the W i reless Settings section of the W ireless Settings page.
Configuring Communication 47 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 3. From within the W ireless Security section, press the Open (Clear T ext) button to open the Open (Clear T ext) Settings dialog (FIG.
Configuring Communication 48 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Configuring the Mode ro’s wireless ca rd for secured access to a WAP200G After logging into the W AP200G, the default Status page appears within the web bro wser .
Configuring Communication 49 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Manually set SSID In the Pr otected Setup page: 1. Select Wireless Settings . 2. Locate the W ireless Security section (FIG. 3 2). 3. Press the Static WEP b utton to open the Static WEP Settings dialog (FIG.
Configuring Communication 50 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom As an example, if you use TECHPUBS as your SSID, you must match this word and the case within both the Network Name (SSID) f ield on the touch panel’ s Network Name SSID f ield and on the W AP’ s Basic W ir eless Conf iguration page.
Configuring Communication 51 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom As an exam ple, enter the w ord AMXPanel using a 128-bit hex digit encr yption.
Configuring Communication 52 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Configuring Multiple Wirel ess Moderos To Communicate To a Target WAP200G 1.
Configuring Communication 53 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Prepare your PC for USB communicati on with the panel If you hav en’t already done so, do wnload and install th e latest versions of Ne tLinx Studio2 and TPDesign4 (from www .
Configuring Communication 54 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 8. Click Ye s to proceed with the driv er installation. Once the install ation is comple te, the pane l and PC are ready to communicate via USB. 9. Navigate back to the System Settings page.
Configuring Communication 55 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 3. Click the Communication s Settings button t o open the Co mmunications Settings dialog. 4. Click the NetLinx Master radio b utton ( fr om the Platform Selection section ).
Configuring Communication 56 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Master Connection to a Virtua l Master via Ethernet Before beginning: 1. V erify the panel has been configured to communicate with the W ireless Access Point and v erify the signal strength quality bar graph is On.
Configuring Communication 57 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 13. After the panel power s-up, pre ss and hold the two lo wer buttons on both sides of the display ( for 3 seconds ) to continue with the setup proces s and proceed to the Setup page.
Configuring Communication 58 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Using G4 Web Control to Interact with a G4 Panel The G4 W eb Control feature allows you to use a PC to interact with a G4 enable d panel via the web .
Configuring Communication 59 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 12. From the W eb Password ke yboard, enter a unique al pha-numeric string to b e assigned as the G4 Authentication se ssion password a ssociated with VNC web access of this panel.
Configuring Communication 60 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom If the Master has been previously conf igured for secur ed communication, cl ick OK to accept the AMX SSL certif icate ( if SSL is enabled ) and then enter a valid username and passw ord into the field s within the Login dialog.
Configuring Communication 61 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 8. In some cases, you might get a Connection Details dialog (FIG. 46) requesting a VNC Server IP Address. This is the IP Address not the IP of the Master bu t of the target touch pane l.
Configuring Communication 62 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom.
Upgrading Modero F irmware 63 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Upgrading Modero Firmware Overview Before beginning the Upgrade process: Setup and conf igure your NetLinx Master . Refer to the your particular NetL inx Master Instruction Manual for detailed setup procedures.
Upgradin g Modero Fi rmware 64 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 5. Press the Back button on the touch panel to retu rn to the Protected Setup page. 6. Press the on-screen Reboot button to both sa ve any changes and r estart the panel.
Upgrading Modero F irmware 65 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 6. Click the Edit Settings button ( on the Communications Settings dialo g ) to open the V irtual NetLinx Master Settings dialog (FIG. 47). 7. From within this dialog enter the System number (default is 1 ).
Upgradin g Modero Fi rmware 66 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 5. If the panel firmware being used is not current, do wnload the latest Kit file by f irst logging in to www .
Upgrading Modero F irmware 67 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Upgrading the Modero Firmware via Ethernet (IP Address) Before beginning with this section, v erify that your panel is powered an d connected to the NetLinx Master through an Ethernet connection (direct or wireless).
Upgradin g Modero Fi rmware 68 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 9. Place a checkmark within the Automatically Ping the Maste r Cont r oller to ensure availability radio box to make sure the Master is initially respond ing online before establ ishing full communication.
Upgrading Modero F irmware 69 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 4. If the panel firmware bein g used is not current, do wnload t he latest Kit file by f irst logging in to www .
Upgradin g Modero Fi rmware 70 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom.
Firmware Pages and Desc riptions 71 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Firmware Pages and Descriptions This section describes each firmware page and their sp ecif ic functional elements. Setup Navigation Buttons These Setup Navigation Buttons (FIG.
Firmware Pages and Descripti ons 72 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Setup Page This page (FIG. 53) centers around basic Modero panel properties such as: Connecti on Status of the pan el, Display T imeout, Inacti vity Page Flip T ime, Inacti vity page fi le, and the Pa nel Brightness.
Firmware Pages and Desc riptions 73 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Information The Informatio n button provides a menu to select either the Pr oject Information P age section on page 74 or the P anel Information P age section on page 75.
Firmware Pages and Descripti ons 74 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Project Informati on Page The Project Information page displays the TPDesign4 (TPD4) project f ile properties current ly loaded on the selected Modero panel (FIG.
Firmware Pages and Desc riptions 75 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Panel Information Page The Panel Information page (FIG. 56) centers around Modero panel prope rties such as: resolution used, on- board memory , firmw are, address/channel info rmation, and st ring info rmation.
Firmware Pages and Descripti ons 76 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Panel Information Page Elements (Cont.) Firmware V ersion: Displays the G4 firmware version being used by the panel. • V erify you have t he latest version from www.
Firmware Pages and Desc riptions 77 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Time & Date Settings Page The options on the T ime & Da te Settings page (FIG. 57) allow you to set and adjust time and date information on the NetLinx Master .
Firmware Pages and Descripti ons 78 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Audio Settings Page The Audio Settings page (accessed by pressing the Au d i o button on the Setup page) allo ws you to adjust the master volume parameters and defa ult panel sounds on the panel.
Firmware Pages and Desc riptions 79 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom En vironmental acoustics, personal v oic e level and ambient noise are all deciding f actors when setting your mic, intercom and panel sound le vels.
Firmware Pages and Descripti ons 80 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Panel Soun ds Information P opup Window Clicking the Inf ormation bu tton in the Default P anel Sounds section opens the P anel Sounds Information popup windo w (FIG.
Firmware Pages and Desc riptions 81 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Video Settings Page The V ideo Settings page (FIG. 61) (accessed by pressing the Vi d e o button on the Setup page) sets the V ideo properties of the incoming video signal from an NXA-A VB/ ETHERNET Breakout Box.
Firmware Pages and Descripti ons 82 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Video Settings Page Elements (Cont.) Hue: Use the UP/DN buttons to alter the hue level of the incoming signal. • Range = 0 - 255, default = 128.
Firmware Pages and Desc riptions 83 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Protected Setup Navigation Buttons The Protected Setup Naviga tion Buttons (FIG. 62) appear on the le ft of the panel screen when the Pr otected Setup page is currently acti ve.
Firmware Pages and Descripti ons 84 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Protected Setup Page The Protected Setup page (FIG. 63) centers around the properties used by the pane l to properly communicate with the NetLinx Master .
Firmware Pages and Desc riptions 85 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Protected Setup Page Elements (Cont.) System Recovery: Allows you to either reset the touch pa.
Firmware Pages and Descripti ons 86 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom System Settings Page The System Settings page (FIG.
Firmware Pages and Desc riptions 87 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom System Settings Page Elements (Cont.) IP Settings: Sets the IP communication val ues for the panel and contains: DHCP/S tatic Sets the panel to either DHCP or S tatic communication modes.
Firmware Pages and Descripti ons 88 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Refer to the Step 3: Choose a Master Connection Mode section on page 52 for more detaile d in formation on using the System Settings page. Wireless Settings Page Use the options on the W ireless Settings page (FIG.
Firmware Pages and Desc riptions 89 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Wireless Settings Page (Cont.) IP Settings: Sets the IP communication values for the panel: DHCP/ST A TIC Sets the panel to either DHCP or S tatic communication modes.
Firmware Pages and Descripti ons 90 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Wireless Settings Page (Cont.) Wireless Security (Cont.): WP A-PSK This button opens the WP A-PSK Settings page (FIG . 71 on page 95). “WP A-PSK” security is designed for environments where is it desirable to use WP A or WP A2, but an 802.
Firmware Pages and Desc riptions 91 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Secondary Connectio n Page The Secondary Connection page sets the communication information for an installe d wireless interf ace card.
Firmware Pages and Descripti ons 92 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Open (Clear Text ) Settings Press the Open (Clear T ext) button to open the Op en (Clear T ext) Settings page (FIG. 69). Wireless Security pages (each Wi Fi card supports diffe rent security features) FIG.
Firmware Pages and Desc riptions 93 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Open security does not utilize any encryption methodology , but requires an SSID (alpha-numer ic) entry .
Firmware Pages and Descripti ons 94 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Static WEP security requires that bot h a target W AP be identified and an encryption method be implemented prior to establishing communication.
Firmware Pages and Desc riptions 95 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Refer to the Conf iguring a W ir eless Network Access section on page 43 for fu rther details on these security options . Refer to the Using the Site Surve y tool section on page 44 for more information on using this feature.
Firmware Pages and Descripti ons 96 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom WP A-PSK security is designed for env ironments where is it desirable to use WP A or WP A2, but an 802.1x authentication server is not a v ailable.
Firmware Pages and Desc riptions 97 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom EAP-LEAP Setting s Press the EAP-LEAP b utton to open the EAP-LEAP Se ttings page (FIG. 72). EAP (Extensible Authentication Protocol) is an Enterprise authentication protocol th at can be used in both wired and wireless network en vironm ents.
Firmware Pages and Descripti ons 98 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Refer to the EAP A uthentication section on page 201 for further deta ils on these security options. Refer to FIG. 73 for an ex ample of what a typi cal EAP-LEAP sy stem c onf iguration page would like.
Firmware Pages and Desc riptions 99 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom FIG. 74 Wireless Settings page - EAP-F AST Settings EAP-FAST Settings SSID (Service Set Identifier): Opens an on-screen keyboard to enter the SSID name used on the target WA P .
Firmware Pages and Descripti ons 100 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom EAP-PEAP Settings Press the EAP-PEAP b utton to open the EAP-PEAP Settings page (FIG.
Firmware Pages and Desc riptions 101 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom There are two main v e rsions of the PEAP protocol su pported by panel’ s DeviceScape W ire.
Firmware Pages and Descripti ons 102 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Refer to the EAP A uthentication section on page 201 for further deta ils on these security options. Refer to the Using the Site Surve y tool section on page 44 for more information on using this feature.
Firmware Pages and Desc riptions 103 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom EAP-TTLS Settings SSID (Service Set Identifier): Opens an on-screen keyboard to enter the SSID name used on the target WA P . The SSID is a unique name used by the W AP , and is assigned to all panels on that network.
Firmware Pages and Descripti ons 104 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Refer to the EAP A uthentication section on page 201 for further deta ils on these security options. Refer to the Using the Site Surve y tool section on page 44 for more information on using this feature.
Firmware Pages and Desc riptions 105 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Refer to the EAP A uthentication section on page 201 for further deta ils on these security options. Refer to the Using the Site Surve y tool section on page 44 for more information on using this feature.
Firmware Pages and Descripti ons 106 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Client certif icate configu ration There are se ve ral ways in which a clie nt certif icate can be configured by an IT dep artment.
Firmware Pages and Desc riptions 107 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Calibration Page This page (FIG. 78) allows you to calibrate the touch panel using a pre-selected touch dri ver . Press and hold the grey Front Setu p Access button (b elo w the Modero LCD) for 6 seconds to access the Calibration page.
Firmware Pages and Descripti ons 108 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom G4 Web Control Page An on-board VNC (V irtual Network Computing) serv er al lo ws the panel to connect to any remote PC running a VNC client. Once connected, the clie nt can vie w and control the panel re motely .
Firmware Pages and Desc riptions 109 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Refer to the Using G4 W eb Contr ol to Interact with a G4 P anel section on page 58 for more detailed instructions on how to use the G4 W eb Control page with the new web-based NetL inx Security application.
Firmware Pages and Descripti ons 110 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Sensor Setup The Sensor Setup page (FIG. 81) allows you to adjust the Light and Motion Sensor parameters on a Modero touch panel. The elements of the Sensor Setup page ar e described in the table be low: FIG.
Firmware Pages and Desc riptions 111 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Sensor Setup Page Elements (Cont.) Light Senso r: Allows you to monitor and alter the sensit .
Firmware Pages and Descripti ons 112 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Making the Most of the Automated Br ightn ess Control Feature (DIM Mode) Please follow the steps below to set up Automated Brightness Control: 1.
Firmware Pages and Desc riptions 113 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Other Settings The Other Settings button pro vides a menu to select the Image Caching page, Passw ord Setup page, or SIP Settings page. Select any opt ion to access its page.
Firmware Pages and Descripti ons 114 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Image Caching Page The Image Caching page (FIG. 83) configures the alloca tion of memo ry for image caching. The G4 graphics engine caches ima ges to decrea se load time of previously viewed images.
Firmware Pages and Desc riptions 115 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Image Caching Page Elements Image Cache Settings: Allocates Flash memory for image caching. Flash Cache Size Press the Up and Down arrows to add and remove memory .
Firmware Pages and Descripti ons 116 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Setting the image cache In the Pr otected Setup page: 1. Press the Cache but ton in the Pr otected Setup Navigation Buttons section. This opens t he Imag e Cache page.
Firmware Pages and Desc riptions 117 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom The elements of the P asswor d Setup page are described in the table belo w: SIP Settings Page The options on the SIP Settings page (F IG. 85) enable you to establish ne twork settings for using your touch panel as an IP phone.
Firmware Pages and Descripti ons 118 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Features on this page include: SIP Settings Page Back: Saves all changes and returns to the previous page. Connection Status icon: The icon in the upper-right corner of each Setup page shows online/offline state of the panel to the master .
Firmware Pages and Desc riptions 119 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Tools The T ools button provides a menu to select either the Pa n e l L o g s Pa g e section on page 119, the P anel Statistics Pa g e section on page 120, or the Connection Utility P age section on page 122.
Firmware Pages and Descripti ons 120 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Features on this page include: Checking the Panel Connection Logs 1. Press the T ools button in the Pr otected Setup Navigation Buttons section.
Firmware Pages and Desc riptions 121 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Features on this page include: FIG. 88 Panel Statistics page Panel Statistics Page Back: Saves all changes and returns to the previous page.
Firmware Pages and Descripti ons 122 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Checking the Pa nel Statistics 1. Press the T ools button in the Pr otected Setup Navigation Buttons section. This opens the T ools menu. 2. W ithin the T ools menu, press the Panel Statistics button.
Firmware Pages and Desc riptions 123 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Features on this page include: Connection Utility Page Close: Closes the Connection Utility popup.
Firmware Pages and Descripti ons 124 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Using the Connection Utility 1. Press the T ools button in the Pr otected Setup Navigation Buttons section. This opens the T ools menu. 2. W ithin the T ools menu, press the Connection Utility b utton.
EAP Security & Server Certifica tes 125 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom EAP Security & Server Certificates Overview The follo wing EAP types all support a.
EAP Security & Server Certificates 126 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom.
Full Duplex Intercom 127 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Full Duplex Intercom Overview V oIP technology gi ves users the ability to instantly crea te a high-quality , di gital home/off ice intercom network with no additional equipmen t required.
Full Duplex Intercom 128 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Setting the Intercom Session Timeout 1. Select th e Setup button on your intercom page. 2. Press the up or down arro ws to increment the timeo ut up by 1 second in each direction.
Full Duplex Intercom 129 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Allowing a panel to be monitored 1. Select th e Setup button on your intercom page. 2. On the intercom setup page, press A dvanc ed Setup . This launches the password numeric ke ypad.
Full Duplex Intercom 130 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom 7. Press Exit when you are finished. Sample Intercom Page The module for duplex intercom capabl e panels includes user pages.
Full Duplex Intercom 131 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Sample Intercom Page ( Cont.) No. Name Description Channel Port:Code Ad dress Port:Code Lev el P or t:Code 7 Panel Directory Room Name The name of a panel in the intercom directory .
Full Duplex Intercom 132 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Answering an incoming cal l The provided in tercom pages include an answering popup windo w . The popup page indicates the name of the panel calling and two options: Answer - Pressing this b utton opens the in tercom session with the other panel.
Full Duplex Intercom 133 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Creating Intercom Pages The easiest method of creating your ow n intercom pages is to start with the pages pro vided by AMX in the module download .ZIP f ile.
Full Duplex Intercom 134 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom.
Programming 135 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Programming Overview Y ou can program the touch panel, using the commands in this secti on, to perform a wide vari ety of operations using Send_Commands and v ariable text commands.
Programming 136 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Page Commands (Cont. ) @DPG Delete a specific popup page from specified popup group if it exists. Syntax: "'@DPG-<popup page name>;<popup group name>'" Va r i a b l e : popup page name = 1 - 50 ASCII characters.
Programming 137 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Page Commands (Cont.) @PP A Close all popups on a specified page. If the page name is empty , the current page is used. Same as the ’Clear Page’ command in TPDesign4.
Programming 138 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Page Commands (Cont. ) @PPM Set the modality of a specific popup page to Modal or NonModal. A Modal popup page, when active, only allows you to use the buttons and featur es on that popup page.
Programming 139 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Page Commands (Cont.) @PSE Set the show effect for the specified popup page to the named show effect. Syntax: "'@PSE-<popup page name>;<show effect name>'" Va r i a b l e : popup page name = 1 - 50 ASCII characters.
Programming 140 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Page Commands (Cont. ) PPOF Deactivate a specific popup page on either a specified page or the current page. If the page name is empty , the cu rr ent page is used (see example 2).
Programming 141 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Programming Numbers The following information provides the progra mming numbers for colors, fonts, and borders. Colors can be used to set the colors on buttons, slider s, and pages.
Programming 142 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom RGB Values for all 88 Basic Colors (Cont.) Index No . Name Red Green B lue 48 V ery Light Blue 0 0 255 49 Light Bl.
Programming 143 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Font Styles and ID Numbers Font styles can be used to program the text fonts on b uttons, sliders, and pages. The following chart shows the default font type and th eir respecti ve ID numbers generated by TPDesign4.
Programming 144 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom TPD4 Border Styles by Name No. Border styles No. Border styles 8 Circle 15 29 Cursor T op 9 Circle 25 30 Cursor T .
Programming 145 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom TPD4 Border Styles by Name No. Border styles No. Border styles 76 Quad Line 1 18 Menu Right Rounded 15 77 Single L.
Programming 146 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands These Button Commands are used in Ne tLinx Studio and are case insensitive. All commands that begin with " ^ " hav e the capability of assigning a variable te xt address range and button state range.
Programming 147 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont.) ^B A U Append unicode text. Same format as ^UNI. Syntax: "'^BAU-<vt addr range>,<button states range>,<unicode text>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 148 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont .) ^BCT Set the text color to the specified color .
Programming 149 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont.) ^BIM Set the input mask for the specified address. Syntax: "'^BIM-<vt addr range>,<input mask>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 150 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont .) ^BMC (Cont.) Example: SEND_COMMAND Panel,"'^BMC-425,1,1,500,1,BR&.
Programming 151 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont.) ^BMF (Cont.) For some of these commands and values, refer to theRGB V alues for all 88 Basic Colors table on page 14 1. ’%CF<on fill color >’ = Set Fill Color.
Programming 152 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont .) ^BMI Set the button mask image. Mask image is used to crop a borderless button to a non-square shap e. This is typically used with a bitmap.
Programming 153 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont.) ^BNP Set the T akeNote network password for the specified Addresses. Syntax: "'^BNP-<vt addr range>,<network password>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 154 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont .) ^BOR Set a border to a specific border style associated with a border value for those buttons with a defined address range. Refer to theBorder Styles and Programming Numbers table on page 143 for more information.
Programming 155 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont.) ^BSF Set the focus to the text area. Note : Select one button at a time (single vari able text address). Do not assign a variable text address range to set focus to multiple buttons.
Programming 156 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont .) ^BVL Log-On/Log-Off the computer control connection. Syntax: "'^BVL-<vt addr range>,<connection>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 157 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont.) ^CPF Clear all page flips from a button. Syntax: "'^CPF-<vt addr range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 158 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont .) ^GDI Change the bargraph drag increment. Syntax: "'^GDI-<vt addr range>,<bargraph drag increment>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 159 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont.) ^GRU Change the bargraph ramp-up time in 1/10th of a second. Syntax: "'^GRU-<vt addr range>,<bargraph ramp up time>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 160 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont .) ^ICO Set the icon to a button. Syntax: "'^ICO-<vt addr range>,<button states range>,<icon index>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 161 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont.) ^JST Set text alignment using a numeric keypad layout for those buttons with a defined address range. The alignment of 0 is followed by ',<left>,<top> '.
Programming 162 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom "^" Button Commands (Cont .) ^SKT Receive touch information on specified socket. Syntax: '^SKT-<0=disable socket, greater than 1023=enable socket on specified port> Only socket values equal to or greater t han 1024 are valid.
Programming 163 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Text Effects Names The follo w ing is a listing of text ef fects names (associated with the ^TEF command on page 162). "^" Button Commands (Cont.) ^UNI Set Unicode text.
Programming 164 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Button Query Commands Button Query commands reply back with a custom ev ent. There will be one custom event for each button/state combination. Each query is assi gned a unique custom ev ent type.
Programming 165 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Button Query Commands ?BCB Get the current border color . Syntax: "'?BCB-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 166 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Button Query Commands (Cont.) ?BCT Get the current text color . Syntax: "'?BCT-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 167 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Button Query Commands (Cont.) ?BOP Get the overall button opacity . Syntax: "'?BOP-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 168 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Button Query Commands (Cont.) ?BWW Get the current word wrap flag status. Syntax: "'?BWW-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 169 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Button Query Commands (Cont.) ?ICO Get the current icon index. Syntax: "'?ICO-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 170 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Button Query Commands (Cont.) ?JSI Get the current icon justification. Syntax: "'?JSI-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 171 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Button Query Commands (Cont.) ?TEC Get the current text effect color . Syntax: "'?TEC-<vt addr range>,<button states range>'" Va r i a b l e : variable text address range = 1 - 4000.
Programming 172 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Panel Runtime Operations Serial Commands are use d in the AxcessX T erminal Emul ator mode. These commands are case insensiti ve. Button Query Commands (Cont.) ?TXT Get the current text information.
Programming 173 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Panel Runtime Operatio n Commands (Cont.) @AKB Pop up the keyboard icon and initialize the tex t string to that specified. Keyboard string is set to null on power up and is stored until power is lost.
Programming 174 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Panel Runtime Operatio n Commands (Cont.) @AKR Remove the Keyboard/ Keypad. Remove keyboard or keypad that was displayed using ' AKEYB', 'AKEYP', 'PKEYP', @AKB, @AKP , @ PKP , @EKP , or @ TKP commands.
Programming 175 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Panel Runtime Operatio n Commands (Cont.) PKEYP Present a private keypad. Pops up the keypad icon and initializes the text string to that specified. Keypad displays a '*' instead of the numbers typed.
Programming 176 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Panel Runtime Operatio n Commands (Cont.) @SSL Change Sleep string. Syntax: "'@SSL-<string>'" Va r i a b l e s : string = name of sleep string.
Programming 177 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Input Commands These Send Commands are case insensitiv e. Panel Runtime Operatio n Commands (Cont.) TP A GEOFF T urn Off p age tracking. Syntax: "'TPAGEOFF'" Example: SEND COMMAND Panel,"'TPAGEOFF'" T urns Off page tracking.
Programming 178 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Input Comm ands (Cont .) ^MBT Set the mouse button mode for the virtual PC. Syntax: "'^MBT-<0-3>'" Va r i a b l e : 0 = None. 1 = Left. 2 = Middle.
Programming 179 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Embedded Codes The following is a list of G4 compatible embedded codes: Embedded Codes Decimal number s Hexidecima.
Programming 180 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Panel Setup Commands These commands a re case insensi tiv e. Panel Setup Commands CLOCK Sets the time and date on the panel.
Programming 181 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Panel Setup Commands (Cont.) ^CFSM Sets the Flash cache to the maximum available size allowed for backup Flash cache. (determined by taking 75% of free Flash space) Syntax: “’^CFSM’” Va r i a b l e : There is no parameter for this command.
Programming 182 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Dynamic Image Commands The following table describe s Dynamic Image Commands. Panel Setup Commands (Cont.) @RPP Reset the protected pas sw ord . @RPP resets the protected password to its default (1988).
Programming 183 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom ^RAF, ^RMF - Embedded Codes The ^RAF and ^RMF commands add and modify any and all resource pa rameters by sending .
Programming 184 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Escape Sequences The ^RAF and ^RMF commands support the replacement of any special escape se quences in the filena.
Programming 185 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Intercom Commands The follo wing is a listing and descri ptions of panel intercom commands. Intercom Co mmands ^ICE Ends an intercom call. Syntax: "'^ICE'" Example: SEND_COMMAND Panel,"'^ICE'" Ends a call.
Programming 186 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom SIP Commands The follo wing table list s and describes SIP commands that are generated from the touch panel. Intercom Co mmands (C ont.) ^ICS S tarts an intercom call to the specified IP address and ports.
Programming 187 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom SIP Commands (Cont.) ^PHN-INCOMING Provides incoming call notification. Provides incoming call notification and the con nection id used for all future commands related to this call.
Programming 188 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom The follo wing table lists an d describes SIP commands that are sent to the touch panel to manage calls. SIP Commands (Cont.) ^PHN- TRANSFERRED Indicates a call has been transferred.
Programming 189 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom SIP Commands (Cont.) ^PHN-HANGUP Hangs up the call. Syntax: "’^PHN-HANGUP, <connection id>’" V.
Programming 190 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom The follo wing table lists and describes SIP setup comma nds. Using any of these co mm ands causes the current user to go of fline. SIP Setup Commands ^PHN-SETUP- DOMAIN Sets the realm for authentication.
Appendix A: Text Formatti ng 191 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Appendix A: Text Formatting Text Formatting Codes for Bargraphs/Joysticks T ext formatting codes .
Appendix A: Text Formatting 192 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Text Area Input Masking T ext Area Input Masking can be used to limi t the allowed/correct characters that are ent ered into a text area.
Appendix A: Text Formatti ng 193 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Refer to the follo wing Send Commands for more detailed information: Input mask ranges These ranges allo w a user to specify the minim um and maximum numeric v alue for a field.
Appendix A: Text Formatting 194 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom When operating with a mask, the mask should be disp layed with placeholders. The "-" character should display where you should enter a charac ter .
Appendix A: Text Formatti ng 195 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Special es cape sequence s The system has only a limited kno wledge of URL formats in that it transparently passes the URL information onto the server for translation.
Appendix A: Text Formatting 196 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom.
Appendix B - Wireless Technology 197 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Appendix B - Wireless Technology Overview of Wireless Technology 802.11b/2.4 GHz and 802.11a/5 GHz are the tw o major WLAN sta ndards and both operate using radio frequency (RF) technology .
Appendix B - Wireless Technology 198 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Terminology 802.1x IEEE 802.1x is an IEEE standard that is b uilt on the Intern et standard EAP (Extensible Authentication Protoc ol).
Appendix B - Wireless Technology 199 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom WP A W i-Fi Protected Access (WP A and WP A2) is a cla ss of system used to secure wireless (W i-Fi) computer networks. It w as created in response to se veral serious weaknesses researchers had found in the pre vious WEP system.
Appendix B - Wireless Technology 200 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom WP A2 Also know as IEEE 802.11i, is an amendment to the 802.11 st andard specifying security mechanisms for wireless networks. The 802.
Appendix B - Wireless Technology 201 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom EAP Authentication EAP (Extensible Authentication Protocol) is an En terprise authenticat ion prot ocol that can be used in both a wired and wireless network en vironm ent.
Appendix B - Wireless Technology 202 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom EAP communication overview EAP Authentication goes a step beyond just encrypting data tr ansfers, but also requires that a set of credentials be va lidated before the client (panel ) is allo wed to connect to the rest of the network (FIG.
Appendix B - Wireless Technology 203 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom AMX Certificate Upload Utility The Certificate Upload utility gi ves you the ability to compi.
Appendix B - Wireless Technology 204 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Step 2: Confirm t he Installation of the USB Driver on the PC The f irst time eac h AMX touch panel i s connected to the PC it is detected as a ne w hardware de vice and the USBLAN dri ver becomes associat ed with it (panel specific).
Appendix B - Wireless Technology 205 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom How to Upload a Certificate File 1. Install the latest AMX USB LAN LINK driv er onto your computer by installing th e latest versions of either TPDesign4 or NetLinx Studio2.
Appendix B - Wireless Technology 206 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom.
Appendix C: Troubleshooting 207 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Appendix C: Troubleshooting This section describes the solutions to possible hardware/firmware issues that could arise during the common operation of a Modero touch panel.
Appendix C: Troubleshooting 208 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Troubleshooting Information (Cont.) Symptom Solution My Modero panel can’t obt ain a DHCP Address In requesting a DHCP Address, the DHCP Server can take up to a few minutes to provide the address.
Appendix C: Troubleshooting 209 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Troubleshooting Information (Cont.) Symptom Solution There is a crawling, dashed line on the left border of the graphics. • On some units at some resolutions, there are wavy lines across the entire screen.
Appendix C: Troubleshooting 210 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with Intercom Troubleshooting Information (Cont.) Symptom Solution I have more that one Mo dero panel connected to my System Maste r and only one shows up.
Appendix C: Troubleshooting 211 NXD-700Vi 7" Modero® Wall/Flush Mount Touch Panel with In tercom.
4/11 © 2011 AMX. All rights reserved. AMX a nd the AMX logo are regist ered trademarks of AM X. AMX reserves the right to alter specific ations without notice at any time. It’s Your World - Take Con trol™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.
Een belangrijk punt na aankoop van elk apparaat AMX nxd-700vi (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen AMX nxd-700vi heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens AMX nxd-700vi vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding AMX nxd-700vi leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over AMX nxd-700vi krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van AMX nxd-700vi bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de AMX nxd-700vi kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met AMX nxd-700vi . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
