Gebruiksaanwijzing /service van het product MX-J900 van de fabrikant JVC
Ga naar pagina of 30
For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference. Model No. Serial No. GVT0037-001A [J] INSTRUCTIONS MX-J900 — Consists of CA-MXJ900 and SP-MXJ900.
– G-1 – W arnings, Cautions and Others CAUTION T o reduce the risk of electrical shocks , fire, etc.: 1. Do not remove scre ws, cov ers or cabinet. 2. Do not expose this appliance to r ain or moisture. 1. CLASS 1 LASER PRODUCT 2. D ANGER : Invisible laser r adiation when open and interlock f ailed or defeated.
– G-2 – GROUND CLAMP ELECTRIC SERVICE EQUIPMENT NEC — NA TIONAL ELECTRICAL CODE POWER SER VICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. P ART H) GROUND CLAMPS GROUNDING CONDUCTORS (NEC SECTION 8.
– 1 – Introduction About This Manual This manual is org anized as follows: • The manual mainly explains operations using the b uttons and controls on the unit. Y ou can also use the b uttons on the remote control if they ha ve the same or similar names (or marks) as those on the unit.
– 2 – Contents Location of the Buttons and Controls ....................... 3 Front Panel ................................................................. 3 Remote Control .......................................................... 5 Getting Started .
– 3 – 1 2 3 6 7 8 9 p q w r t u i 4 5 e y o j l k / z x c v b ; a s d f g h Location of the Buttons and Controls Become familiar with the b uttons and controls on your unit. Front Panel Powered Rolling Panel Press P ANEL OPEN/ CLOSE to open the panel.
– 4 – See pages in the parentheses for details. Front Panel 1 Disc trays 2 PO WER button and ST ANDBY lamp (9) 3 Display windo w 4 SUBWOOFER V OLUME control (10) 5 Remote sensor 6 T APE 2 3 button and lamp (9, 16) Pr essing this button also turns on the unit.
– 5 – When using the remote control, point it at the remote sensor on the front panel. Remote Control Remote Control 1 Disc number buttons (CD1, CD2, and CD3) (13) Pr essing one of these buttons also turns on the unit.
– 6 – Getting Started Unpacking After unpacking, check to be sure that you ha ve all the follo wing items. The number in the parentheses indicates the quantity of the pieces supplied. • AM loop antenna (1) • FM antenna (1) • Remote control (1) • Batteries (2) If any is missing, consult your dealer immediately .
– 7 – 1 Connect the AM loop antenna to the AM LOOP terminals as illustrated. 2 T urn the AM loop antenna until you ha ve the best r ece ption. T o connect an outdoor AM antenna When reception is poor , connect a single vinyl-covered wir e to the AM EXT terminal and extend it horizontally .
– 8 – T o start the display demonstration manually Press and hold DEMO f or more than 2 seconds. T o stop the demonstration, press any button. T o connect audio equipment with an optical digital input terminal Y ou can record CD sound onto the connected digital equipment.
– 9 – Common Operations T urning On or Off the Power T o turn on the unit, press PO WER so that the ST ANDBY lamp goes off. The Po wered Rolling Panel opens automatically . T o turn off the unit (on standby), press PO WER again so that the ST ANDBY lamp lights up.
– 10 – Reinforcing the Bass Sound The SUBWOOFER VOLUME control pro vided for this unit can enhance the subwoofer sound if subwoofers are connected to the rear of this unit (see page 7). This function only af fects the playback sound , b ut does not affect y our recording.
– 11 – Surround modes * : D.CLUB : Increases resonance and bass. HALL : Adds depth and brilliance to the sound. ST ADIUM : Adds clarity and spreads the sound, like in an outdoor stadium. SEA (Sound Effect Amplifier) modes: R OCK : Boosts lo w and high frequency .
– 12 – Listening to FM and AM Broadcasts T uning in a Station 1 Pr ess FM/AM. The unit automatically turns on and tunes in the previously tuned sta tion (either FM or AM). The P owered Rolling Panel automatically opens. • Each time you press the button, the band alternates between FM and AM.
– 13 – Playing Back CDs Loading CDs On the unit ONL Y : 1 Pr ess 0 f or the disc tray (CD1 to 3) y ou want to load a CD onto. The unit automatically turns on and the disc tray comes out. T he Powered Rolling Panel also opens automatically . 2 Place a disc correctl y on the circle of the disc tray , with its label side up.
– 14 – T o locate a particular point in a track During play , press and hold 1 or ¡ . • 1 : Fast re verses the disc. • ¡ : Fast forw ards the disc. When using the remote control, press and hold 1 / 4 or ¢ / ¡ . T o go to another track Press 4 or ¢ repeatedly before or during playback.
– 15 – T o stop during play , press 7 . • Random play also stops when one of the disc trays is opened. T o e xit fr om Random play mode, press PROGRAM/ RANDOM repeatedly again before or after play so that the unit enters another play mode.
– 16 – Playing Back T apes Y ou can play back type I, type II, and type IV tapes without changing any settings. Playing Back a T ape 1 Pr ess EJECT ( 0 ) for the deck y ou want to use. 2 Put a cassette in, with the exposed part of the tape down. 3 Close the cassette holder gently .
– 17 – Recording Recording a T ape on Deck B 1 Press EJECT 0 f or the deck B. 2 Put in a recordab le cassette, with the exposed part of the tape down. 3 Close the cassette holder gently . 4 Check the tape direction of deck B. • If the tape direction is not correct, press T APE 2 3 twice then 7 to change the tape direction.
– 18 – CD Direct Recording Everything on the CD goes onto the tape in the order it is on the CD, or according to the order you hav e made for Program play . 1 Put a recordable cassette into deck B. 2 Place a disc correctl y on the circle of the disc tray , with its label side up.
– 19 – Auto Edit Recording By using Auto Edit Recording, you can record the CD tracks to f it the tape. Auto Edit Recording makes a program by selecting the CD tracks in numerical order . Howe ver , to prev ent the end of the last track on the front side from being cut off , the last track is selected so as to fit on the remaining tape length.
– 20 – Using the T imers There are three timers av ailable — Recording T imer, Daily T imer , and Sleep T imer . Before using the timers, you need to set the clock built in the unit. (See page 9.) Using Daily Timer W ith Daily T imer , you can wake to your fa vorite music or radio program.
– 21 – DAILY Canceled ON TIME ON TIME Clock setting (See page 9.) REC 6 When selecting “– CD – –” 1) Press 4 or ¢ to select the disc number , then press SET . 2) Press 4 or ¢ to set the track number , then press SET . The unit enters volume setting mode.
– 22 – Recording Timer 7:00 6:30 Sleep Timer 7:30 does not work. Recording Timer AM 6:00 7:30 7:00 6:30 Daily Timer AM 6:00 Using Sleep T imer W ith Sleep T imer , you can fall asleep to music. Y ou can set Sleep T imer when the unit is turned on.
– 23 – Maintenance T o get the best performance of the unit, keep your discs, tapes, and mechanism clean. Handling cassette tapes • If the tape is loose in its cassette, take up the slack by inserting a pencil in one of the reels and rotating. • If the tape is loose, it may get stretched, cut, or caught in the cassette.
– 24 – Specifications Amplifier section — CA-MXJ900 Output P ower SUBWOOFERS: 150 W per channel, min. RMS, driven into 6 Ω at 63 Hz with no more than 10% total harmonic distortion. MAIN SPEAKERS:50 W per channel, min. RMS, driv en into 6 Ω at 1 kHz with no more than 10% total harmonic distortion.
Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production of the wide array of JVC products, service is the key to maintaining the high level of performance for which JVC is world famous.
LIMITED W ARRANTY A UDIO-1 JVC COMP ANY OF AMERICA warrants this product and all parts thereof, e xcept as set for th below ONL Y TO THE ORIGINAL PURCHASER A T RET AIL to be FREE FR OM DEFECTIVE MA TERIAL AND WORKMANSHIP from the date of original retail purchase f or the per iod as shown belo w .
VICTOR COMP ANY OF JAP AN , LIMITED 0100MWMMDWJEM EN J V C MX-J900[J].COVER/f 00.1.13, 3:05 PM 2.
Een belangrijk punt na aankoop van elk apparaat JVC MX-J900 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen JVC MX-J900 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens JVC MX-J900 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding JVC MX-J900 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over JVC MX-J900 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van JVC MX-J900 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de JVC MX-J900 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met JVC MX-J900 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
