Gebruiksaanwijzing /service van het product RX-D401S van de fabrikant JVC
Ga naar pagina of 52
LVT1436-001A [J] RX-D401S / RX-D402B A UDIO / VIDEO CONTR OL RECEIVER INSTR UCTIONS For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear , bottom or side of the cabinet. Retain this information for future reference.
W arnings, Cautions, and Others Mises en gar de , précautions et indications diver ses Caution–– STANDBY/ON button! Disconnect the mains plug to shut the power off completely. The STANDBY/ON button in any position does not disconnect the mains line.
1 Intr oduction We would like to thank y ou for purchasing one of our JVC products . Before operating this unit, read this man ual carefully and thoroughly to obtain the best possible perf or mance from y our unit, and retain this manual for future ref erence.
2 Ta b le of Contents Pa r ts identification ................................................ 3 Getting started ...................................................... 6 Before Installation ..............................................................
3 A/V CONTROL RECEIVER REMOTE CONTROL RM -SRXD401J TV/VIDEO A UDIO TV DBS/CA TV DVR/D VD FM USB VCR TV DBS D VR/DVD AM VCR TV VOL CHANNEL VOLUME MUTING TUNING/REW FF/TUNING SETTING D VD MENU ADJUST EXIT AUDIO INPUT VIDEO INPUT DECODE MODE D .EQ FREQ D .
4 Front panel 1 ST ANDBY/ON button and standby lamp (16) 2 DIMMER button (18) 3 SETTING button (20, 22) 4 ADJUST button (27) 5 SURROUND b utton (37) 6 HDMI lamp (9) 7 Source lamps D VR/D VD , VCR, DBS.
5 1 Po wer cord (14) 2 HDMI terminals (9) VCR (DBS) IN, D VR/D VD IN, MONITOR OUT 3 AV COMPU LINK- III terminals (38) 4 DIGIT AL IN ter minals (14) • Coaxial: 1(D VR/D VD) • Optical: 2(DBS) • Op.
6 Putting batteries in the remote control Before using the remote control, put tw o supplied batter ies first. 1 Press and slide the battery cover on the bac k of the remote control. 2 Insert batteries. Make sure to match the polarity: (+) to (+) and (–) to (–).
7 ANTENNA COAXIAL FM 75 AM EXT AM LOOP ANTENNA Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna. Connecting the FM and AM antennas Do not connect the A C power plug to the wall outlet until all connections are completed.
8 FL FR SL SR SBL C SW SBR (*SB) LEFT RIGHT LEFT RIGHT LEFT RIGHT SUBWOOFER OUT SURROUND SPEAKERS CAUTION:SPEAKER IMPEDANCE 6 - 16 SURROUND BACK SPEAKERS CENTER SPEAKER FRONT SPEAKERS Connecting the speakers Do not connect the A C power plug to the wall outlet until all connections are completed.
9 VCR(DBS) IN DVR/DVD IN MONITOR OUT HDMI Connecting video components Do not connect the A C power plug to the wall outlet until all connections are completed. HDMI connection IMPORT ANT : The HDMI video signals from the HDMI terminal are transmitted onl y through the HDMI MONIT OR OUT terminal.
10 ı Ή Ï Ì Ç Å DVR OUT(REC) DVR/DVD IN(PLAY) Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN DVR OUT(REC) DVR/DVD IN(PLAY) FRONT Audio/video connection In addition to the HDMI te.
11 Å Ï Ó ı Ç Î ‰ Ì Ô DVR OUT(REC) DVR/DVD IN(PLAY) DVR OUT(REC) DVR/DVD IN(PLAY) FRONT COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN DVD MULTI IN CENTER SUBWOOFER SURR-L SURR-R È Y P B.
12 VCR OUT(REC) IN(PLAY) AUDIO OUT(REC) IN(PLAY) VCR Å ı Ή Ï Ì Ç Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN Å 7 Connecting a VCR T urn off all components bef ore making connections. • When you connect other components , refer also to their manuals.
13 Å ı Î Ç Y P B P R COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN TV IN D B I N L R MONITOR OUT / DVD P LAY) COMPONENT VIDEO MONITOR OUT DVR/DVD IN VCR(DBS) IN Y P B P R VIDEO VC OUT(REC) DB.
14 DIGITAL OUT PCM/STREAM DIGITAL IN 2(DBS) 1(DVR/ DVD) 3(VCR) NO TES • When shipped from the f actor y , the DIGIT AL IN terminals have been set for use with the f ollowing components: – 1(D VR/D.
15 USB connection This receiver is equipped with a USB terminal on the front panel. Y ou can connect your PC to this terminal and enjoy sound reproduced through your PC . When you connect y our PC for the first time , follow the procedure below . • Remember you cannot send any signal or data to y our PC from this receiv er.
16 Basic operations 2 Select the source to play On the front panel: T urn SOURCE SELECTOR until the sour ce name y ou want appears on the display . The source lamp corresponding to the selected source lights in red. • As you turn SOURCE SELECTOR, the source changes as f ollo ws: D VR/D VD: Select this for the D VD recorder or D VD play er .
17 3 Adjust the volume To increase the v olume , turn MASTER V OLUME control c lockwise (or press V OLUME + on the remote control). To decrease the v olume , turn MASTER V OLUME control counter cloc kwise (or press V OLUME – on the remote control). • When you adjust the v olume, the volume le vel indication appears on the displa y for a while.
18 Selecting the digital decode mode This receiver automatically detects the incoming digital signal for mat when “HDMI” or “DIGIT AL ” is selected in “A UDIO INPUT” setting (see page 17). When “HDMI” or “DIGIT AL ” is selected, the digital decode mode is set to “DGTL (digital) AUT O .
19 Basic adjustment of auto memory This receiv er memor izes sound settings for each source: • when you turn off the power , and • when you change the source . When you change the source , the memorized settings for the newly selected source are automatically recalled.
20 To obtain the best possible sound eff ect from Surround/DSP modes (see pages 33 to 37), you need to set up the speak er and subwoof er information after all the connections are completed. F rom pages 20 to 26, how to set speakers and other basic items of the receiv er are explained.
21 Speakers (channels) number and the size Y ou can find how each of the speak er size is defined according to the number of connected speakers (speak er channel “ch” number) y ou select. • Subwoof er is counted as 0.1 channel. The size of connected speak ers CH FL/FR C SL/SR SB SUBWFR 2.
22 Operating procedure Menu operation buttons On the front panel: From the remote control: Before y ou star t, remember ... There is a time limit in doing the f ollowing steps. If the setting is canceled before y ou finish, star t from step 1 again. In this section, the operation of the remote control is used f or e xplaining.
23 In this case, set the distance as f ollows: Left front speaker (FL): “FRONT L <3.0m> (10ft)” Right front speaker (FR): “FRONT R <3.0m> (10ft)” Center speaker (C): “CENTER <3.0m> (10ft)” Left surround speaker (SL): “SURR L <2.
24 NO TES • This function is not available when “SURR OUND SPK” is set to “NO” (see page 22). • When “S BA CK SPK” is set to “NO” (see page 22), the Vir tual Surround Back (see page 36) is applied f or EX/ES/PLIIx (6.1- channel) reproduction.
25 Using the Midnight mode —MIDNIGHT MODE Y ou can enjoy a po werful sound at night using the Midnight mode. When the Midnight mode is activ ated, the MIDNIGHT indicator lights up on the display . MIDNIGHT < OFF > Select when you w ant to enjoy surround with its full dynamic range .
26 Setting the Audio delay level —AUDIO DELA Y Synchronization between audio and video reproduction can be possibly disturbed because video signal decoding is time- consuming compared to the audio signal decoding. On this setting, you can correct synchronization between video and audio signals by dela ying the audio signal timing.
27 Sound adjustments Y ou can make sound adjustment to y our preference after completing basic setting. Basic adjustment items Y ou can adjust the follo wing items. See pages in parentheses f or details. •Y ou cannot select the items which is not av ailable with the current setting.
28 4 Press 2 / 3 button repeatedl y to adjust the selected item. • On the front panel, turn MUL TI JOG. Y our adjustment is stored. 5 Press SET . 6 Repeat steps 2 to 5 to adjust other items if necessary . 7 Press EXIT . • On the front panel, press ADJUST .
29 Adjusting the bass sounds Reinforcing the bass—BASS BOOST Y ou can boost the bass lev el—Bass Boost. • Once you hav e made an adjustment, it is memorized for each source. B BOOST < ON > Select to boost the bass lev el. The B.BOOST indicator lights up on the displa y .
30 Adjusting the panorama control for Pro Logic IIx Music and Pro Logic II Music—P ANORAMA This setting is av ailable when Pro Logic IIx Music or Pro Logic II Music is activated f or the analog or digital 2-channel sound signal. To activate Pro Logic IIx Music or Pro Logic II Music , see page 37.
31 T uner operations T uning in to stations manually From the remote control ONL Y : 1 Press FM or AM to select the band. The last receiv ed station of the selected band is tuned in. 2 Press repeatedly or hold TUNING 9 or ( TUNING until the station y ou want is tuned in.
32 3 Press the numeric b uttons (1 – 10, +10) to select a channel number while the c hannel n umber position is flashing. •F or channel number 5, press 5. •F or channel number 15, press +10, then 5. •F or channel number 30, press +10, +10, then 10.
33 Creating realistic sound fields Reproducing theater ambience In a movie theater , many speakers are located on the walls to reproduce impressiv e multi-channel sound, reaching you from all directions. With these many speakers , sound localization and sound mov ement can be expressed.
34 DTS Neo:6 DTS Neo:6 is another conv ersion method to create 6-channel (plus subwoof er) from analog/digital 2-channel software by using the high precision digital matrix decoder used for DTS-ES Matrix 6.1ch. • This receiver provides the f ollowing DTS Neo:6 modes— Neo:6 Cinema (NEO:6 CINEMA) and Neo:6 Music (NEO:6 MUSIC).
35 Introducing the DSP modes The sound heard in a concer t hall, club , etc. consists of direct sound and indirect sound—early reflections and reflections from behind. Direct sounds reach the listener directly without any reflection. On the other hand, indirect sounds are dela yed by the distances of the ceiling and walls.
36 Using the Surround/DSP modes Av ailable Surround/DSP modes v ar y depending on the speaker settings and the incoming signals. See the table below . • The numbers inside the parentheses follo wing the incoming signal type indicate the number of the front channels and that of the surround channels.
37 On the front panel: Before y ou star t, remember ... There is a time limit in doing the f ollowing steps. If the setting is canceled before y ou finish, star t from step 2 again. 1 Select and play an y source. • Surround/DSP modes are not av ailable when multi channel PCM (see page 34) signals recorded in D VD-Audio are coming.
38 AV COMPU LINK EX AV COMPU LINK- III AV COMPU LINK AV COMPU LINK AV COMPU LINK- III AV COMPU LINK remote contr ol system The A V COMPU LINK remote control system allows y ou to operate JVC’ s video components (TV , D VD play er*, and VCR) through this receiver .
39 One-touch DVD play Simply by starting playbac k on the D VD play er, y ou can enjoy the D VD playback without setting other s witches manually . The follo wing is set automatically: •T ur ning on the receiver . • Changing the source to “D VR/D VD .
40 Y ou can use the supplied remote control to operate not onl y this receiver but also other JVC pr oducts. • Refer also to the man uals supplied with the other products. – Some JVC VCRs can accept two types of the control signals—remote codes “A” and “B.
41 123 456 789 10 0 10 Y ou can alwa ys perform the follo wing operation: D VR/DVD : Tu rn on or off the D VD recorder or D VD play er . After pressing D VR/D VD , you can perf or m the follo wing operations on the D VD recorder and D VD play er. 3 : Star t playbac k.
42 By changing the transmittable signals, you can use the supplied remote control to operate other man ufacturers’ products. • Refer also to the man uals supplied with the other products.
43 ❏ Changing the transmittable signals for operating a VCR 1 Press and hold VCR . 2 Press VCR. 3 Enter the manufacturer’ s code using buttons 1 – 9, and 0. See “Manufacturers’ codes for VCR” on the r ight. 4 Release VCR . Now , you can perform the f ollowing operation on the VCR.
44 Manufacturer Codes G.I. 01 Gemini 02 Hamlin 03, 04, 05, 06 Jerrold 07, 08, 09, 10, 11, 12, 13, 14, 15 Macom 16, 17, 18 Magnavox 19 Oak 20, 21, 22 Panasonic 23, 24 Philips 25, 26, 27, 28, 29, 30 Pioneer 31, 32 S.
45 Tr oubleshooting Use this chart to help you solve daily operational prob lems. If there are any prob lems you cannot solv e, contact your JVC’ s service center. PROBLEM The power does not come on. The receiv er tur ns off (enters standby mode). “O VER HEA T” flashes on the displa y , then the receiv er tur ns off.
46 Remote control does not operate as y ou intend. Remote control does not work. Continuous hiss or buzzing during FM reception. Occasional crac king noise dur ing FM reception. The remote control is not ready f or your intended operation. There is an obstruction hiding the remote sensor on the receiv er.
47 Designs and specifications are subject to change without notice. Amplifier Output Power At stereo operation: F ront channels: 110 W per channel, min. RMS, driven into 6 Ω at 20 Hz to 20 kHz with no more than 0.8% total harmonic distortion. At surround operation: F ront channels: 110 W per channel, min.
warranty.p65 05.7.1, 7:59 PM 1.
warranty.p65 05.7.1, 7:59 PM 2.
0705RYMMDWJEIN EN © 2005 Victor Company of Japan, Limited AUDIO / VIDEO CONTROL RECEIVER RX-D401S / RX-D402B cover_RX-D401S[J]_f.p65 05.7.1, 7:58 PM 2.
Een belangrijk punt na aankoop van elk apparaat JVC RX-D401S (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen JVC RX-D401S heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens JVC RX-D401S vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding JVC RX-D401S leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over JVC RX-D401S krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van JVC RX-D401S bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de JVC RX-D401S kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met JVC RX-D401S . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
