Gebruiksaanwijzing /service van het product SP-UXP400 van de fabrikant JVC
Ga naar pagina of 32
MICRO COMPONENT SYSTEM UX-P400 —Consists of CA-UXP400 and SP-UXP400 INSTRUCTIONS GVT0128-003A [B] Cover[B].fm Page 1 Sunday, January 18, 2004 6:58 PM.
G-1 Warnings, Cautions and Others CAUTION—STANDBY/ON button! Disconnect the mains plug to shut the power off completely (all lamps and indications go off). The STANDBY/ON button in any position does not disconnect the mains line. • When the unit is on standby, the STANDBY/ON lamp lights in red.
1 Contents Introduction ........................................................ 2 Precautions .......................................................................... 2 How to Read This Manual .................................................. 2 Getting Started .
2 Introduction Precautions Installation • Install in a place which is level, dry and neither too hot nor too cold—between 5°C and 35°C. • Install the System in a location with adequate ventilation to prevent internal heat buildup inside the System.
3 Getting Started Step 1 : Unpack After unpacking, check to be sure that you have all the following items. The number in parentheses indicates the quantity of each piece supplied. • FM antenna (1) • AM loop antenna (1) • Remote control (1) • Batteries (2) If any item is missing, consult your dealer immediately.
4 Step 3 : Hook Up If you need more detailed information, see page 6. AUX LEFT RIGHT AUDIO OUT Illustrations of the input/output terminals below are typical examples. When you connect other components, refer also to their manuals since the terminal names actually printed on the rear may vary.
5 PUSH OPEN AU TO R EV ER S E FM antenna (supplied) Extend it so that you can obtain the best reception. AM loop antenna (supplied) Turn it until the best reception is obtained.
6 To assemble and connect the AM loop antenna To assemble the AM loop antenna To connect the AM loop antenna • If the AM loop antenna wire or speaker cords are covered with vinyl, remove the vinyl to expose the tip of the antenna by twisting the vinyl.
7 Before Operating the System The indications on the display teach you a lot of things while you are operating the System. Before operating the System, be familiar with when and how the indicator illuminates on the display. 1 Rhythm Ax indicator • Lights when Rhythm Ax is activated.
8 Daily Operations —Playback 1 Turn on the power. The STANDBY/ON lamp on the main unit lights in green. • Without pressing STANDBY/ON , the System turns on by pressing one of the source selecting buttons in the next step. 2 Select the source. Playback automatically starts if the selected source is ready to start.
9 To tune in to a station While FM or AM is selected... Frequency starts changing on the display. When a station (frequency) with sufficient signal strength is tuned in, the frequency stops changing. • When you repeatedly press the button, the frequency changes step by step.
10 To select a track To select a group (MP3 only) Before starting playback... Group number and group name appear. To locate a particular portion While playing a disc, press and hold until the portion you want is reached. To locate a track directly and start play Playing Back a Tape To insert a tape You can play back tapes of types I, II, and IV.
11 Daily Operations —Sound&Other Adjustments Adjusting the Volume You can adjust the volume level from level 0 (VOL MIN) to level 40 (VOL MAX). To drop the volume in a moment Adjusting the Sound To emphasize rhythm feeling—RHYTHM AX This function emphasizes bass attack feeling, and also changes the subwoofer level.
12 Changing the Display Brightness You can dim the display window. Setting the Clock Without setting the built-in clock, you cannot use Daily/ Recording Timers (see page 21) and Sleep Timer. • To exit from the clock setting, press CLOCK/TIMER as required.
13 Advanced Radio Operations Receiving FM Stations with RDS Radio Data System (RDS) allows FM stations to send an additional signal along with their regular program signals. • When tuned to an FM station which provides the RDS service, the RDS indicator lights on the display.
14 3 Start searching. The receiver searches 30 preset FM stations, stops when it finds the one you have selected, and tunes in to that station. • If no program is found, “NOTFOUND” appears on the display. • To stop searching any time during search, press PTY SEARCH.
15 Description of the PTY codes NEWS News. AFFAIRS Topical program expanding or enlarging upon the news—debate, or analysis. INFO Programs the purpose of which is to impart advice in the widest sense. SPORT Programs concerned with any aspect of sports.
16 Advanced Disc Operations Programming the Playing Order— Program Play You can arrange the playing order of the tracks (up to 50) before you start playback. 1 Before starting playback, activate Program Play. 2 Select tracks you want for Program Play.
17 To check the programmed contents Before or after playback... To modify the program Before or after playback... To exit from Program Play Before or after playback... • Exiting from Program Play erases the stored program. Playing at Random—Random Play You can play all tracks at random.
18 Playing Repeatedly—Repeat Play You can repeat playback. Before starting playback... While playing... To repeat a particular portion—A-B Repeat You can repeat a particular portion while playing back a CD. 1 During playback, activate A-B Repeat. 2 Select the start point (A).
19 Advanced Tape Operations Recording on a Tape You can use type I tapes for recording. • To play a tape, see page 10. 1 Insert a recordable cassette. 2 Check the tape running direction and Reverse Mode settings on the display. To change the direction To change the Reverse mode if necessary REV.
20 3 Select and start playing the source—“FM,” “AM,” “CD,” or “AUX.” • When recording a disc, you can also use “Synchronized Disc Recording” (see below). 4 Start recording. Synchronized Disc Recording You can start and stop both disc play and tape recording at the same time.
21 Timer Operations Setting the Timer Using Daily Timer, you can wake up with your favorite song. On the other hand, with Recording Timer, you can make a tape of a radio broadcast automatically.
22 3 Select the volume level. • You can select the volume level ( “ VOLUME 0 ” to “ VOLUME 40 ” and “ VOLUME – –” ). If you select “ VOLUME – – , ” the volume is set to the last level when the unit has been turned off. For Recording Timer: 1 Set the hour then the minute for on-time.
23 To turn off the Timer after its setting is done Since Daily Timer is activated at the same time everyday, you may need to cancel it on some particular days. • Recording Timer can also be canceled temporarily. 1 Select the Timer you want to cancel.
24 Additional Information Learning More about This System Daily Operations—Playback (see pages 8 to 10) Listening to the Radio: • If you store a new station into an occupied preset number, the previously stored station in that number will be erased.
25 Troubleshooting If you are having a problem with your System, check this list for a possible solution before calling for service. General: Adjustments or settings are suddenly canceled before you finish. ] There is a time limit. Repeat the procedure again.
26 Specifications Amplifier section Output Power: 40 W (20 W + 20 W) at 4 Ω (10% THD) Speakers/Impedance: 4 Ω – 16 Ω Audio Input AUX: 400 mV/50 k Ω Tuner section FM tuning range: 87.
SAFETY INSTRUCTIONS “SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT” This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
MEMO ME MO . f m Pag e 1 W e d n e sd ay , J an u ar y 21, 2004 6: 03 PM.
MEMO ME MO . f m Pag e 2 W e d n e sd ay , J an u ar y 21, 2004 6: 03 PM.
VICTOR COMPANY OF JAPAN, LIMITED 0104AIMMDWJEM EN © 2004 VICTOR COMPANY OF JAPAN, LIMITED UX-P400 MICRO COMPONENT SYSTEM Cover[B].fm Page 2 Sunday, January 18, 2004 6:58 PM.
Een belangrijk punt na aankoop van elk apparaat JVC SP-UXP400 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen JVC SP-UXP400 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens JVC SP-UXP400 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding JVC SP-UXP400 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over JVC SP-UXP400 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van JVC SP-UXP400 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de JVC SP-UXP400 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met JVC SP-UXP400 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
