Gebruiksaanwijzing /service van het product EZ-EXTENDER 82-000218-01 van de fabrikant Analog Devices
Ga naar pagina of 42
Bluetooth EZ-Extender ® Manual Revision 1.0, October 2009 Part Number 82-000218-01 Analog Devices, Inc. One T echnology W ay N orwood, Mass. 02062-9106 a.
Copyright Information © 2009 Analog Devices, Inc., ALL RIGHTS RESERVED. This docu- ment may not be reproduced in an y form without prior , express written consent from Analog Devices, Inc. Printed in the USA. Disclaime r Analog Devices, Inc. reserves the right to change this product without prior notice.
Regulatory Compliance The Bluetooth EZ-Extender is designed to be used solely in a laboratory environment. The board is not intended for use as a consumer end prod- uct or as a portion of a consumer end product.
.
Bluetooth EZ-Extender Manual v CONTENTS PR E F A C E P roduct Over view ............................................................................ x P urpose of This Manual .................................................................. xi Intended A udience .
CONTENTS vi Bluetooth EZ-Extender Manual UAR T Interface ............................................................................ 1-4 Bluetooth M odule ........................................................................ 1-5 USB Interface ....
Bluetooth EZ-Extender Manual vii CONTENTS BLUETOOTH EZ-EXTENDER B ILL OF MATERIALS BLUETOOTH EZ-EXTENDER SCHEMATIC T itle P age .................................................................................... B-1 M odule ..........................
CONTENTS viii Bluetooth EZ-Extender Manual.
Bluetooth EZ-Extender Manual ix PREFACE Thank you for purchasing the Bluetooth EZ-Extender ® , Analog Devices, Inc. daughter board to a Blackf in evaluation syst em with the new expansion interface II (such as th e ADSP-BF518F EZ-Board™) or the older STAMP interface (such as the ADSP-BF537 EZ-KIT Lite ® ).
Product Overview x Bluetooth EZ-Extender Manual Product Overview The Bluetooth EZ-Extender is a separate ly sold daughter board that plugs onto an EZ-KIT Lite supporting the STAMP interf ace or an EZ-Board/EZ-Kit Lite supporting the expansion interface II connec- tor.
Bluetooth EZ-Extender Manual xi Preface All of the power necessary to operate the extender is de rived from the mat- ing EZ-KIT Lite/EZ-Board. Before using any of the interfaces, follow the setup procedure in “Bluetooth EZ-Extender Setup” on page 1-4 .
What’s New in This Manual xii Bluetooth EZ-Extender Manual • Appendix A, “Bluetooth EZ-Extender Bill Of Materials” on page A-1 Provides a list of components used to manufacture the board. • Appendix B, “Bluetooth EZ-Extender Schematic” on page B-1 Provides the resources to allow bo ard-level debugging or to use as a reference guide.
Bluetooth EZ-Extender Manual xiii Preface • Contact your Analog Devices, I nc. local sales office or authorized distributor • Send questions by mail to: Analog Devices, Inc.
Product Information xiv Bluetooth EZ-Extender Manual Analog Devices Web Site The Analog Devices Web site, www.analog.com , provides information about a broad range of products—analog integrated circ uits, amplifiers, converters, and digital signal processors.
Bluetooth EZ-Extender Manual xv Preface Data sheets, which can be downloaded from the Analog De vices Web site, change rapidly, and therefore are not included on the technical library CD. Technical manuals change periodica lly. Check the Web site for the latest manual revisions and associated documentation errata.
Notation Conventions xvi Bluetooth EZ-Extender Manual Notation Conventions Text conventions used in this manual are identified and described as fol- lows. Additional conventions, which appl y only to specific chapters, may appear throughout this document.
Bluetooth EZ-Extender Manual 1-1 1 USING BLUETOOTH EZ-EXTENDER This chapter describes the Bluetoot h EZ-Extender’s package contents, configuration, installation procedure, and interfaces. The information is presente d in the following order. • “Package Contents” on page 1-2 Describes the product’s package contents.
1-2 Bluetooth EZ-Extender Manual • “Expansion Interface” on page 1-6 Describes the board’s expansion interface. • “Example Programs” on page 1-6 Describes the example programs installed with the board’s software. For more information about the mating Blackfin processor, see documents referred to as “Related Documents” .
Bluetooth EZ-Extender Manual 1-3 Bluetooth EZ-Extender Default Configuration When removing the Bluetooth EZ-Extender from the package, handle the board carefully to avoid the discharge of static electricity, which can dam- age some components (see Figure 1-1 ).
1-4 Bluetooth EZ-Extender Manual Figure 1-1 shows the default jumper and sw itch settings, connector loca- tions, and LED used in installation. Confirm that your board is in the default configuration be fore using the board.
Bluetooth EZ-Extender Manual 1-5 Bluetooth Module The Bluegiga WT12 module is a ne xt-generation, clas s 2, Bluetooth 2.0 plus EDR module. The WT12 is a highly integrated and sophisticated Bluetooth module, containing all of the necessary elements from Blue- tooth radio antenna to a fully impleme nted protocol stack.
1-6 Bluetooth EZ-Extender Manual Expansion Interface Expansion interface connectors on top of the Bluetooth EZ-Extender allow other EZ-Extenders to be mounted on top of the Bluetooth EZ-Extender. The UART interface is not brought up to the expansion interface because the interface is us ed by the WT12 Blue tooth module.
Bluetooth EZ-Extender Manual 2-1 2 BLUETOOTH EZ-EXTENDER HARDWARE REFERENCE This chapter describes the hardware de sign of the Bluetooth EZ-Extender. The following topics are covered.
System Architecture 2-2 Bluetooth EZ-Extender Manual System Architecture A block diagram of the Blueto oth EZ-Extender is shown in Figure 2-1 . The block diagram illustrates how the UART, SPORT, and USB ports are interfaced the Bluetooth module and processor on a mating EZ-KIT Lite/EZ-Board.
Bluetooth EZ-Extender Manual 2-3 Bluetooth EZ-Extender Hardware Reference The board contains a Bluegiga WT12 class 2, a Bluetooth 2.0, and EDR module, described in “Bluetooth Module” on page 1-5 . The EZ-Extender is equipped with an I 2 C serial flash memory chip for data storage and configuration.
Configuration Switch 2-4 Bluetooth EZ-Extender Manual Positions 7 and 8 of the configuration switch enable or disable UART flow control. Other switch positions are intended for internal Analog Devices test purposes only and not supported. By default, SW1 is all OFF .
Bluetooth EZ-Extender Manual 2-5 Bluetooth EZ-Extender Hardware Reference Jumpers This section describes functionality of the configuration jumpers. Figure 2-3 shows the jumper locations.
Jumpers 2-6 Bluetooth EZ-Extender Manual TWI Flash Address Configuration Jumper (JP1) The TWI flash address configuration jumper ( JP1 ) controls the base address of the configuration flas h memory.
Bluetooth EZ-Extender Manual 2-7 Bluetooth EZ-Extender Hardware Reference Power LED This section describes the power LED ( LED1 ). When LED1 is lit up, it indi- cates that the board is powered.
Connectors 2-8 Bluetooth EZ-Extender Manual Connectors This section describes connector fu nctionality and provides information about mating connectors. The connector locations are shown in Figure 2-5 . Dashed lines indicate connect ors on the bottom side of the board.
Bluetooth EZ-Extender Manual 2-9 Bluetooth EZ-Extender Hardware Reference STAMP UART Connector (J1) The STAMP UART connector ( J1 ) allows the Bluetooth EZ-Extender to be plugged onto an EZ-KIT Lite development board supporting a STAMP interface. The J1 connector is located on the bottom side of the board.
Connectors 2-10 Bluetooth EZ-Extender Manual Expansion Interface II Connector (J5) The board-to-board connector ( J5 ) provides signals for the PPI, TWI interfaces and GPIO signals of the mating EZ-Board. The connector is located on the bottom side of the boar d.
Bluetooth EZ-Extender Manual 2-11 Bluetooth EZ-Extender Hardware Reference Expansion Interface II Connector (P4) The board-to-board connector ( P4 ) provides signals for the PPI, TWI interfaces and GPIO signals of the mating EZ-Board. The connector is located on the top side of the board.
Connectors 2-12 Bluetooth EZ-Extender Manual.
Bluetooth EZ-Extender Manual A-1 A BLUETOOTH EZ-EXTENDER BILL OF MATERIALS The bill of materials corresponds to “Bluetooth EZ-Extender Schematic” on page B-1 .
A-2 Bluetooth EZ-Extender Manual 13 1 IDC 4X2 IDC4X2 JP3 SULLINS GEC04DAAN 14 1 IDC 25x2 IDC25x2_SMT A P2 SAMTEC TS SH-125-01-L-D V -A 15 1 IDC 35x2 IDC35x2_SMT A P4 SAMTEC TS SH-135-01-L-D V -A 16 1 .
D 4 3 2 1 A B C 20 Cotton Road Nashua, NH 03063 A B C D 4 3 2 1 PH: 1-800-ANALOGD C Title Size Board No. Date Sheet of DEVICES ANALOG Rev A0218-2008 BLUETOOTH EZ-EXTENDER 1.
V_SELECT 3.3V 3.3V V_SELECT WC GND VCC E0 E1 E2 SCL SDA V_SELECT V_SELECT VCCY Y A VCCA GND 3.3V VCCY Y8 Y7 Y6 Y5 A8 A7 A6 A5 Y1 Y2 Y3 Y4 A1 A2 A3 A4 VCCA EN GND 3.
3.3V 3.3V V_SELECT 3.3V1 3.3V2 DRPRI DRSEC GND1 GND2 GND3 GND4 GND5 GND6 GPIO2 GPIO4 NC RFS RSCLK RSVD2 RSVD4 RSVD6 RSVD8 SDA SPISEL1 SPISEL3 SPISS TFS TIMER UARTCTS UARTRX PWR_IN1 PWR_IN2 VDDIO1 VDDIO2 RSVD10 RSVD9 SPISEL2 SPICLK DTPRI TSCLK DTSEC SPIMOSI SPIMISO SCL UARTTX UARTRTS RESET GPIO1 GPIO3 WAKE RSVD3 RSVD5 RSVD7 3.
V_SELECT RSVD7 RSVD2 SDA RSVD1 RSVD4 RSVD5 RSVD3 RSVD6 GND6 TIMER2/GPIO TIMER1/GPIO GND1 GND2 GND3 GND4 PWR_IN2 VDDIO1 PPI0D0 PPI0CLK PPI0D1 PPI0D10 PPI0D11 PPI0D12 PPI0D13 PPI0D14 PPI0D15 PPI0D16 PPI.
Bluetooth EZ-Extender Manual I-1 II N D E X A architecture, of this EZ-Extender, 2-2 B bill of materials, A-1 Bluetooth module, 1-5 , 2-2 Bluetooth module default config jumper (JP5), 2-6 board schema.
INDEX I-2 Bluetooth EZ-Extender Manual S schematic, of Bluetooth EZ-E xtender, B- 1 setup, of this EZ-Extender, 1- 3 , 1-4 soft reset config jumpers (JP3-4), 2-6 STAMP UART connector (J1), 2-9 support.
Een belangrijk punt na aankoop van elk apparaat Analog Devices EZ-EXTENDER 82-000218-01 (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Analog Devices EZ-EXTENDER 82-000218-01 heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Analog Devices EZ-EXTENDER 82-000218-01 vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Analog Devices EZ-EXTENDER 82-000218-01 leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Analog Devices EZ-EXTENDER 82-000218-01 krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Analog Devices EZ-EXTENDER 82-000218-01 bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Analog Devices EZ-EXTENDER 82-000218-01 kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Analog Devices EZ-EXTENDER 82-000218-01 . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
