Gebruiksaanwijzing /service van het product 300 Series, 300 Series van de fabrikant Kenmore
Ga naar pagina of 48
• W arranty • Installation • S t art Up / Setting T imer • How It W orks • Care Of • S pecifications • Repair Part s W ater Sof teners With Deluxe V alve Sears, Roebuck and Co., 3333 Beverly Road, Hoffman Est ates, IL 60179 USA www .KenmoreW ater .
2 Questions? Call The Kenmore W ater Line 1-800-426-9345 W ARRANTY ON W A TER SOFTENER ONE YEAR LIMITED W ARRANTY ON W A TER SOFTENER When installed, operated and maint ained according to all instruct.
3 T ABLE OF CONTENTS Safety Guides ................................................................................................................. ................................ 4 Unpack and Check Shipment .........................................
Saf ety Guides 4 Y Read all steps, guides and rules carefully before inst alling and using your new water softener . Follow all steps exactly to correctly inst all. Failure to follow them could cause personal injury or property damage. Reading this book will also help you to get all of the benefits from your water softener .
5 Unpac k and Check Y our Car ton FIG . 1 Questions? Call The Kenmore W ater Line 1-800-426-9345 Packing List INSPECT SHIPMENT Y our water softener is shipped complete in one carton. Use care when handling the softener . DO NOT turn upside down. DO NOT drop, or set on sharp objects that could make a hole in the bottom.
6 Plan Y our Installation PLAN YOUR INST ALLA TION It is recomended to read through the entire manual before beginning your installation. Follow all step s exactly .
7 Plan Y our Installation FIG . 3 T ypical Inst allation 1. Place as close as possible but always after , the pressure tank (well water) or water meter (city water). See Fig. 3. 2. Place as close as possible to a water drain such as a floor drain, laundry tub, sump or stand pipe.
8 Plan Y our Installation Suggested Slab Foundation Inst allation Plug the softener transformer into an inside, 120 volt 60Hz electrical outlet. If an outside outlet is used, be sure it has approved weather protection. Run drain tubing to laundry tub or p-trap inside home, if possible.
9 PIPE, FITTINGS, OTHER MA TERIALS NEEDED Y ou must first decide how to run “in” and “out” pipes to the softener . Look at your house main water pipe at the point you will connect the softener .
10 R ead Bef or e Be ginning Installa tion BEFORE INST ALLING CHECKS & TESTS Y our water supply needs to be checked for chemical analysis, water pressure and water flow rate.
11 FIG . 9 INST ALLING BYP ASS V AL VE, AND/OR INLET AND OUTLET THREADED ADAPTORS Clip (2) V alve Outlet Included with Softener Included with Softener V alve Inlet ASSEMBLE INLET OUTLET ADAPTORS, OR PLASTIC BYP ASS V AL VE Complete the following steps to assemble the adaptors or bypass valve.
12 Install 3-V alv e Bypass INST ALLING 3 V AL VE BYP ASS AND PIPES Complete the following steps to inst all the three (3) valve bypass: • Cut the house main water pipe where you will con- nect the softener . • Loosely put together pipe, fittings, and the three (3) valves.
13 Loca te Wa ter Softener and Connect Pipes MOVE SOFTENER INTO PLACE Grip under ridge to move softener . Plywood Shims TYPICAL SOLDERING CONNECTIONS Main W ater Pipe Hard W ater 1. Cut pipe to correct length. 2. Solder (WHEN COOL, do S tep 3). 3. Put threaded adaptor into bypass valve port.
14 Connect V alv e and Salt T ank Dr ains CONNECT THE V AL VE DRAIN HOSE T ake a length of 3/8” inside diameter drain tubing and attach one end to the drain fitting. See Fig. 16. Use a tube clamp to hold it in place. Put the other end of the tubing over a floor drain, into a laundry tub, stand pipe, or other suitable drain.
15 Leak T est LEAK TEST T o check for leaks, complete the following steps: CAUTION: T o avoid water or air pressure dam- age to softener inner parts, and to flush pipe chips or other residue from the water pipes, be sure to do the following steps exactly as instructed.
16 Electrical R equir ements INST ALL GROUNDING CLAMP BETWEEN THE SOFTENER IN AND OUT PIPES The house cold water pipe (iron or copper) is often used to ground all electrical outlets in the home. Outlets are grounded to protect you from shock when you touch any electric appliance plugged into the out- let.
17 Install Co v er s and R estar t Wa ter Hea ter FIG . 23 INST ALL COVERS After inst alling your water softener , replace the covers. Angle the covers so the main cover clips onto the back first, then bring down in front and clip on the two (2) tabs inside the rim of the salt hole and lower the salt cover closed.
18 Pr og r am T he Timer Large Capacity Display DOWN Button UP Button REGENERA TION Button SELECT Button Model 38306 Model 39306 PROGRAM THE TIMER 1. When the transformer is plugged in, a model code and a test number (example: J1.1) show in the face plate.
19 Pr og r am T he Timer SET W A TER HARDNESS NUMBER T o set the water hardness number , complete the follow- ing steps: 1. Press the SELECT button once to display the words SET HARDNESS and a flashing 25 . The grains per gallon (gpg) hardness of your water supply is on your water analysis report.
20 Sanitize T he W ater Softener SANITIZE THE W A TER SOFTENER Care is taken at the factory to keep your water sof tener clean and sanitary . Materials used to make the softener will not infect or contaminate your water supply , or cause bacteria to form or grow .
21 Adding Salt T o T he Stor a ge T ank ADDING SAL T TO THE ST ORAGE T ANK Brine (salt dissolved in water) is needed for each and every regeneration. The water for making brine is metered into the salt storage tank by the sof tener .
22 Chec k List CHECK LIST OF STEP-BY -STEP GUIDES T O INST ALL Review the following list to ensure you have completed all the installation procedures. ____1. Check the incoming water . Has incoming water been tested? ____2. Remove cardboard packaging from salt t ank.
23 FIG . 33 F acepla te Timer F ea tur es FIG . 31 FIG . 32 EXTRA RECHARGE Sometimes, a manually started regeneration (recharge) may be desired, or needed. T wo examples are: • Y ou have used more water than usual (guests visiting) and you may run out of soft water before the next timer started regeneration.
24 F acepla te Timer F ea tur es FIG . 34 Questions? Call The Kenmore W ater Line 1-800-426-9345 California Efficiency Requirement Y our Kenmore W ater Softener has a “High Efficiency” feature with an “ON” or “OFF” setting.
25 Ho w Y our W ater Softener W or ks FIG . 37 SOFT W A TER SERVICE AND REGENERA TION SERVICE When the softener is giving you sof t water , it is called “Service”. See Fig. 36. During service, hard water comes from the house main water pipe into the soften- er .
26 Ho w Y our W ater Softener W or ks SOFT W A TER SERVICE AND REGENERA TION BRINING: During brining, the brine is moved from the salt storage area, into the resin tank. See Fig. 38. Inside the resin tank, brine cleans hardness minerals from the resin beads and they are discharged out the drain.
27 Ho w Y our W ater Softener W or ks F AST RINSE: Backwash is followed by a fast flow of water down through the resin tank. The fast flow packs the resin bed and gets it ready for return to service. See Fig. 40. After fast rinse, the sof tener returns to service.
28 Car e Of Y our Wa ter Softener FIG . 41 SAL T BRIDGE Sometimes, a hard crust or salt bridge forms in the salt storage tank. It is usually caused by high humidity or the wrong kind of salt. When the salt bridges, an empty space forms between the water and salt.
29 Car e Of Y our Wa ter Softener FIG . 42 KEEPING THE W A TER SOFTENER CLEAN NOZZLE & VENTURI A clean nozzle and venturi (see Fig. 42) is a must for the softener to work right. This small unit moves brine from the salt storage tank to the resin t ank during regeneration.
30 Car e Of Y our Wa ter Softener PROTECT THE W A TER SOFTENER FROM FREEZING If the softener is inst alled where it could freeze (sum- mer cabin, lake home, etc.), you must drain all water from it to stop possible freeze damage. T o drain the sof- tener: 1.
31 Car e Of Y our Wa ter Softener CHECKLIST TO HELP YOU SA VE MONEY If your water softener fails to work, make the following easy checks. Of ten, you will find what is wrong yourself and you won’t have to call and wait for service.
32 Specifica tions FIG . 44 Questions? Call The Kenmore W ater Line 1-800-426-9345 A B F C D E E Inches CM A Salt T ank Height 40-1/4 102.2 B Resin T ank Diameter (nominal) 8 20.3 C Resin T ank Height (nominal) 40 101.6 D Inlet-Outlet Height 41-1/2 105.
33 Specifica tions FIG . 45 Questions? Call The Kenmore W ater Line 1-800-426-9345 Intermittent flow rate does not represent the maximum service flow rate used for determining the soften- ers rated capacity and ef ficiency . Continuous operation at flow rates greater than the service flow rate may affect cap acity and efficiency performance.
34 Ser vice T ec h Infor mation FIG . 46 Keep this manual with your water softener . If repairs are needed, the service technician must have the informa- tion on the following pages. AL W A YS MAKE THESE INITIAL CHECKS FIRST 1. Does the time display show the correct time of day? • If display is blank, check power source to the sof- tener .
35 Ser vice T ec h Infor mation FIG . 47 The faceplate timer (PW A) computer has a self-diag- nostic function for the electrical system, except put power and water meter . The computer monitors elec- tronic components and circuit s for correct operation.
36 Ser vice T ec h Infor mation TROUBLESHOOTING V AL VE POSITION INDICA TORS: Depending on the valve position, the following indica- tors show in the display: Indicator V alve Position Serv ..................................... Service Fill...........
37 Ser vice T ec h Infor mation MANUAL ADV ANCE REGENERA TION CHECK This check verifies proper operation of the valve motor , brine tank fill, brine draw , regeneration flow rates, and other controller functions. Always make the initial checks, and the manual initiated diagnos- tics.
38 Ser vice T ec h Infor mation ROT AR Y V AL VE SERVICE IMPORT ANT : Before working on the valve, turn off the water supply and disconnect from electrical power . TO RELIEVE PRESSURE: • 3 V AL VE BYP ASS: Close the inlet valve and open a soft water faucet.
39 FIG . 56 Drain from valve inlet (Hard W ater) Bypass Hard W ater T o V alve Outlet Position Switch BRINING AND BRINE RINSE CYCLE Brine from Salt S torage T ank Nozzle V enturi Ser vice T ec h Infor mation SERVICE CYCLE Hard water enters the valve inlet port.
40 Ser vice T ec h Infor mation Drain Bypass Hard W ater T o V alve Outlet Position Switch BACKW ASH CYCLE Flow Plug FIG . 57 Questions? Call The Kenmore W ater Line 1-800-426-9345 BACKW ASH CYCLE T imer/switch action again allows the motor to turn the rotor & disc to place the valve in BACKW ASH, stopping water flow to the nozzle.
41 Notes Questions? Call The Kenmore W ater Line 1-800-426-9345.
42 4 3 1 2 5 6 28 27 7 Rating Decal Location 8 26 25 24 23 22 21 20 9 10 11 12 13 14 18 17 16 19 15 Kenmore MODEL Nos. 625.383060 and 625.393060 Exploded V iew Questions? Call The Kenmore W ater Line .
43 P ar ts List Kenmore MODEL Nos. 625.383060 and 625.393060 A. W A TER SOFTENER COMPLETE Key No. Part Number Part Description 1 ---- Cover Lock (Required for shipping only) 1 ---- Rim Insert (Require.
44 Exploded V iew 19 18 17 1 2 3 4 5 6 7 8 9 16 15 14 13 12 10 20 11 INLET - OUTLET GROUNDING CLAMPS Kenmore MODEL Nos. 625.383060 and 625.393060 Questions? Call The Kenmore W ater Line 1-800-426-9345.
45 P ar ts List Kenmore MODEL Nos. 625.383060 and 625.393060 B. BRINE V AL VE ASSEMBL Y Key No. Part Number Part Description 1 7168647 Ceramic Weight 2 0513860 Float S top 3 7097202 Float (includes Key No.
46 Exploded V iew 1 3 47 46 2 3 4 5 6 7 45 8 9 10 11 44 12 13 14 15 16 42 43 41 40 39 38 37 36 35 34 33 32 31 28 29 27 26 22 23 24 25 Seal Wear-S trip 17 18 19 20 21 Cross-Section View 30 Questions? C.
47 P ar ts List Key Part No. Number Part Description 1 7224087 Screw , #8-32 x 1" (2 req.) 2 7286039 Motor (incl. 2 ea. of Key No. 1) 3 0900857 Screw , #6-20 x 3/8" (2 req.
® Registered Trademark / TM Tradema rk / SM Ser vice Mark of Sears Brands, LLC ® Mar ca Regi strada / TM Marca d e Fábr ica / SM Marca de Servicio de Se ars Brands, LLC MC Marque de commerce / MD M.
Een belangrijk punt na aankoop van elk apparaat Kenmore 300 Series, 300 Series (of zelfs voordat je het koopt) is om de handleiding te lezen. Dit moeten wij doen vanwege een paar simpele redenen:
Als u nog geen Kenmore 300 Series, 300 Series heb gekocht dan nu is een goed moment om kennis te maken met de basisgegevens van het product. Eerst kijk dan naar de eerste pagina\'s van de handleiding, die je hierboven vindt. Je moet daar de belangrijkste technische gegevens Kenmore 300 Series, 300 Series vinden. Op dit manier kan je controleren of het apparaat aan jouw behoeften voldoet. Op de volgende pagina's van de handleiding Kenmore 300 Series, 300 Series leer je over alle kenmerken van het product en krijg je informatie over de werking. De informatie die je over Kenmore 300 Series, 300 Series krijgt, zal je zeker helpen om een besluit over de aankoop te nemen.
In een situatie waarin je al een beziter van Kenmore 300 Series, 300 Series bent, maar toch heb je de instructies niet gelezen, moet je het doen voor de hierboven beschreven redenen. Je zult dan weten of je goed de alle beschikbare functies heb gebruikt, en of je fouten heb gemaakt die het leven van de Kenmore 300 Series, 300 Series kunnen verkorten.
Maar de belangrijkste taak van de handleiding is om de gebruiker bij het oplossen van problemen te helpen met Kenmore 300 Series, 300 Series . Bijna altijd, zal je daar het vinden Troubleshooting met de meest voorkomende storingen en defecten #MANUAl# samen met de instructies over hun opplosinge. Zelfs als je zelf niet kan om het probleem op te lossen, zal de instructie je de weg wijzen naar verdere andere procedure, bijv. door contact met de klantenservice of het dichtstbijzijnde servicecentrum.
